Rui Pan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Rui Pan has a total of 108 co-authors. Here are the top co-authors by number of shared publications:
Shujun Chen
11 shared publicationsPei Chen
7 shared publications- Jin Yang
School of Materials Engineering, Shanghai University of Engineering Science, ShangHai, CHINA
5 shared publications - Minlin Zhong
Tsinghua University
5 shared publications Taoshuai Zhou
5 shared publicationsFei Qin
4 shared publications
Latest Publications
- 16 January 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (1)
Influence of air gap on the sapphire/Invar36 alloy joints by ultrafast laser direct micro-welding
The effect of interfacial air gap width on ultrafast laser micro-welding of sapphire to Invar36 alloy was systematically investigated for the first time. To precisely control the air gap width (optical contact, 0.36, 0.84, 1.32, 1.60, and 2.26 μm), ultrafast laser micromachining technology was applied. Small gaps (optical contact to 1.32 μm) promoted material intermixing and mechanical interlocking, while large gaps (1.60–2.26 μm) induced defects such as microcracks and voids. Therefore, shear strength gradually decreased from 242.7 to 13.6 MPa as the gap increased to 1.32 μm, and it suddenly dropped to 0 MPa when the gap was above 1.60 μm. Joint formation was attributed to nano-/micro-particle bridging from laser-induced Invar plasma. In summary, an acceptable gap tolerance between 0.36 and 0.84 μm is recommended for industrial applications, yielding 28–48.5 MPa strength which is compatible with the brazed joints.
- 16 January 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (1)
Influence of air gap on the sapphire/Invar36 alloy joints by ultrafast laser direct micro-welding
The effect of interfacial air gap width on ultrafast laser micro-welding of sapphire to Invar36 alloy was systematically investigated for the first time. To precisely control the air gap width (optical contact, 0.36, 0.84, 1.32, 1.60, and 2.26 μm), ultrafast laser micromachining technology was applied. Small gaps (optical contact to 1.32 μm) promoted material intermixing and mechanical interlocking, while large gaps (1.60–2.26 μm) induced defects such as microcracks and voids. Therefore, shear strength gradually decreased from 242.7 to 13.6 MPa as the gap increased to 1.32 μm, and it suddenly dropped to 0 MPa when the gap was above 1.60 μm. Joint formation was attributed to nano-/micro-particle bridging from laser-induced Invar plasma. In summary, an acceptable gap tolerance between 0.36 and 0.84 μm is recommended for industrial applications, yielding 28–48.5 MPa strength which is compatible with the brazed joints.
- Top Cited PapersOpen Access
An Active Interfacial Drag- and Heat-Reduction Technique Based on a Windward Concave Cavity Design: Reverse Jetting
The airflow velocity at the solid–air interface is directly proportional to the generated drag and heat. Therefore, reducing drag and heat at such interfaces under extreme operating conditions (e.g., supersonic flight) is particularly important. In contrast to the passive drag-reduction technique, which cannot significantly reduce drag and heat, in this study, an active interface drag- and heat-reduction technique based on a windward concave cavity (reverse jet) is presented. The effect of the number of jet holes, their relative position, size, and other parameters on the drag and heat at 6.5 Mach is investigated using the FLOEFD simulation software. The results show that a five-hole cross-distributed jet achieves the best thermal protection: the total surface static pressure, drag, and surface temperature are reduced by 51.7%, 33.9%, and 31.2%, respectively, compared with the case without a reverse jet. This study provides guidance for the structural design of thermal protection and drag-reduction systems.
Top Cited PapersOpen AccessAn Active Interfacial Drag- and Heat-Reduction Technique Based on a Windward Concave Cavity Design: Reverse Jetting
The airflow velocity at the solid–air interface is directly proportional to the generated drag and heat. Therefore, reducing drag and heat at such interfaces under extreme operating conditions (e.g., supersonic flight) is particularly important. In contrast to the passive drag-reduction technique, which cannot significantly reduce drag and heat, in this study, an active interface drag- and heat-reduction technique based on a windward concave cavity (reverse jet) is presented. The effect of the number of jet holes, their relative position, size, and other parameters on the drag and heat at 6.5 Mach is investigated using the FLOEFD simulation software. The results show that a five-hole cross-distributed jet achieves the best thermal protection: the total surface static pressure, drag, and surface temperature are reduced by 51.7%, 33.9%, and 31.2%, respectively, compared with the case without a reverse jet. This study provides guidance for the structural design of thermal protection and drag-reduction systems.
- Open Access
- 17 September 2025
- Published by Elsevier in Materials & Design
- Vol. 259
Direct joining of sapphire and Invar alloy by nanosecond laser
- 17 September 2025
- Published by Elsevier in Materials & Design
- Vol. 259
Open AccessDirect joining of sapphire and Invar alloy by nanosecond laser
A Laser Synthesis Strategy to Boost Oxygen Evolution Kinetics on Stainless Steel‐Based Catalyst via Dual‐Metal Segmentally Coordinated Reaction Centers for Efficient Alkaline Water Splitting
The fabrication of efficient, stable, and noble‐metal‐free electrocatalysts for the hydrogen energy field has been of great interest, but still faces numerous challenges, especially in the development of fast and convenient strategies. This study reports a state‐of‐the‐art strategy for the ultrafast preparation of spinel‐type oxide self‐supporting catalysts on stainless steel by ultrafast two‐step laser synthesis. The self‐supporting catalytic electrode not only possesses remarkable superhydrophilic/superaerophobic properties but also the constructed (Ni, Fe, Co)(Fe, Cr) 2 O 4 ·(O x H y )@SS304 microcone array catalyst also demonstrates a superior oxygen evolution reaction (OER) performance with a low overpotential of 130 mV at 10 mA cm −2 , a Tafel slope of 34.0 mV dec −1 , and outstanding long‐term stability (a negligible overpotential decay of ≈5% at 10 mA cm −2 for over 88 h). The laser‐fabricated catalysts exhibit optimal performances, surpassing that of the best previously reported stainless steel‐based OER catalysts. First‐principles calculations also reveal that the reaction mechanism of the as‐prepared catalyst is affiliated with the oxide path mechanism dominated by the exposed (220) crystal facet, and dual‐metal segmentally coordinated reaction centers effectively reduce the oxygen evolution energy barriers, boosting the OER kinetics. This work may open up a new path to design multi‐metal‐based self‐supporting catalysts for hydrogen energy applications.
A Laser Synthesis Strategy to Boost Oxygen Evolution Kinetics on Stainless Steel‐Based Catalyst via Dual‐Metal Segmentally Coordinated Reaction Centers for Efficient Alkaline Water Splitting
The fabrication of efficient, stable, and noble‐metal‐free electrocatalysts for the hydrogen energy field has been of great interest, but still faces numerous challenges, especially in the development of fast and convenient strategies. This study reports a state‐of‐the‐art strategy for the ultrafast preparation of spinel‐type oxide self‐supporting catalysts on stainless steel by ultrafast two‐step laser synthesis. The self‐supporting catalytic electrode not only possesses remarkable superhydrophilic/superaerophobic properties but also the constructed (Ni, Fe, Co)(Fe, Cr) 2 O 4 ·(O x H y )@SS304 microcone array catalyst also demonstrates a superior oxygen evolution reaction (OER) performance with a low overpotential of 130 mV at 10 mA cm −2 , a Tafel slope of 34.0 mV dec −1 , and outstanding long‐term stability (a negligible overpotential decay of ≈5% at 10 mA cm −2 for over 88 h). The laser‐fabricated catalysts exhibit optimal performances, surpassing that of the best previously reported stainless steel‐based OER catalysts. First‐principles calculations also reveal that the reaction mechanism of the as‐prepared catalyst is affiliated with the oxide path mechanism dominated by the exposed (220) crystal facet, and dual‐metal segmentally coordinated reaction centers effectively reduce the oxygen evolution energy barriers, boosting the OER kinetics. This work may open up a new path to design multi‐metal‐based self‐supporting catalysts for hydrogen energy applications.
- 30 May 2025
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 342
Femtosecond laser-induced microjet assisted one-step fabrication of through-silicon vias
- 30 May 2025
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 342
Femtosecond laser-induced microjet assisted one-step fabrication of through-silicon vias
- Open Access
- 1 April 2025
- Published by Tsinghua University Press in Journal of Advanced Ceramics
- Vol. 14 (4)
Femtosecond laser-induced honeycomb structure on the interface for the micro-welding of YSZ/sapphire
Femtosecond laser welding, a novel technique for material joining, faces challenges such as stringent pre-welding requirements and low joint strength when directly welding ceramics. In this study, we addressed the issues associated with the direct welding of YSZ and sapphire by first depositing a nanometer-thick Ti layer on the ceramic surface, followed by femtosecond laser welding. Notably, we observed for the first time that femtosecond laser pulses induce the formation of a honeycomb structure at the interface, forming a YSZ/Sapphire micro-welding joint characterized by a continuous structure, a honeycomb structure, and Ti-rich phases. This specific joint distribution significantly enhances the interface transition and improves the joint strength. Under conditions of 8 W laser power, a scanning speed of 50 mm/s, and a pulse frequency of 200 kHz, the micro-welding joint exhibited optimal interface performance, achieving a maximum shear strength of approximately 79 MPa. Through calculations of the temperature distribution of the interface and the surface energy of the crystal, we conclude that the honeycomb structure arises from the Ti layer, the temperature gradient distribution and the tendency of sapphire to melt along directions exhibiting lower surface energy. The honeycomb structure effectively enriches the transition between the micro-welding interface and the substrate. The new findings of this study offer valuable insights and potential pathways for the reliable and efficient welding of advanced ceramics.
- 1 April 2025
- Published by Tsinghua University Press in Journal of Advanced Ceramics
- Vol. 14 (4)
Open AccessFemtosecond laser-induced honeycomb structure on the interface for the micro-welding of YSZ/sapphire
Femtosecond laser welding, a novel technique for material joining, faces challenges such as stringent pre-welding requirements and low joint strength when directly welding ceramics. In this study, we addressed the issues associated with the direct welding of YSZ and sapphire by first depositing a nanometer-thick Ti layer on the ceramic surface, followed by femtosecond laser welding. Notably, we observed for the first time that femtosecond laser pulses induce the formation of a honeycomb structure at the interface, forming a YSZ/Sapphire micro-welding joint characterized by a continuous structure, a honeycomb structure, and Ti-rich phases. This specific joint distribution significantly enhances the interface transition and improves the joint strength. Under conditions of 8 W laser power, a scanning speed of 50 mm/s, and a pulse frequency of 200 kHz, the micro-welding joint exhibited optimal interface performance, achieving a maximum shear strength of approximately 79 MPa. Through calculations of the temperature distribution of the interface and the surface energy of the crystal, we conclude that the honeycomb structure arises from the Ti layer, the temperature gradient distribution and the tendency of sapphire to melt along directions exhibiting lower surface energy. The honeycomb structure effectively enriches the transition between the micro-welding interface and the substrate. The new findings of this study offer valuable insights and potential pathways for the reliable and efficient welding of advanced ceramics.