Xuefei Xuan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xuefei Xuan has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Zhiwei Zhang
Hangzhou Dianzi University
21 shared publications Chao Le
Hangzhou Dianzi University Hangzhou China
17 shared publications- Zhiqun Cheng
School of Electronics and Information, Hangzhou Dianzi University, Hangzhou, China
17 shared publications - Tingwei Gong
School of Electronics and Information, Hangzhou Dianzi University, Hangzhou, China
13 shared publications Zhiqun Cheng
Hangzhou Dianzi University Hangzhou China
5 shared publicationsBrendan Hayes
School of Electronic Engineering, Dublin City University, Dublin 9, Ireland
4 shared publications
Latest Publications
- 21 June 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
A High‐Efficiency Continuous Class‐F GaAs HBT Power Amplifier Enabled by Chip‐Package Co‐Designed Output Matching Network
This paper introduces a high‐efficiency GaAs HBT MMIC power amplifier (PA). A chip‐package co‐design strategy is proposed, in which high‐Q bonding wires are innovatively employed to replace lossy on‐chip inductors in the output matching network. This approach not only significantly reduces insertion loss but also leverages the favorable high‐frequency characteristics of the bonding wires to mitigate impedance deviations at the second and third harmonics, thereby satisfying the requirements of continuous Class‐F operation. The proposed theory is validated by designing a GaAs HBT PA operating from 5.9 to 7.1 GHz. The MMIC PA has a power‐added efficiency (PAE) of 46%–52% with an output power of 32.9–33.7 dBm. When driven by a 20 MHz, 256 QAM modulation signal, the measured EVM is better than 1.35%. In addition, the chip area is reduced to 1.04 mm 2 , demonstrating that low‐loss matching synthesis using bonding wires is an effective approach for realizing high‐efficiency and compact RF front‐end PAs.
- 21 June 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
A High‐Efficiency Continuous Class‐F GaAs HBT Power Amplifier Enabled by Chip‐Package Co‐Designed Output Matching Network
This paper introduces a high‐efficiency GaAs HBT MMIC power amplifier (PA). A chip‐package co‐design strategy is proposed, in which high‐Q bonding wires are innovatively employed to replace lossy on‐chip inductors in the output matching network. This approach not only significantly reduces insertion loss but also leverages the favorable high‐frequency characteristics of the bonding wires to mitigate impedance deviations at the second and third harmonics, thereby satisfying the requirements of continuous Class‐F operation. The proposed theory is validated by designing a GaAs HBT PA operating from 5.9 to 7.1 GHz. The MMIC PA has a power‐added efficiency (PAE) of 46%–52% with an output power of 32.9–33.7 dBm. When driven by a 20 MHz, 256 QAM modulation signal, the measured EVM is better than 1.35%. In addition, the chip area is reduced to 1.04 mm 2 , demonstrating that low‐loss matching synthesis using bonding wires is an effective approach for realizing high‐efficiency and compact RF front‐end PAs.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (4) , 2809-2820
Collaborative Optimization Method for Wideband Transistor-Based Rectifiers With a Large Input Power Dynamic Range
This paper presents a collaborative optimization method for the design of wideband transistor-based rectifiers with a large input power dynamic range, targeting high-power energy harvesting and wireless power transfer applications. The core of the proposed method is to establish the relationship between the rectification efficiency, the continuous mode parameter,andthe input power range at several representative frequencies ofthecontinuous class-B/J mode, from which the target load impedance range under different frequencies and power levels is obtained. With the target impedance identified, an Ivy algorithm (IVYA)-driven intelligent optimization framework is then employed to enable the automated design and optimization of subsequent circuit topologies. To verify the proposed method, a wideband transistor-based rectifier operating from 2.2 to 2.6 GHz is designed, fabricated, and measured. The prototype achieves a peak efficiency of 63.5%–76.3% within the operating band, and maintains above 50% efficiency at a 17 dB input power back-off level, demonstrating the effectiveness and applicability of the proposed collaborative optimization method in the design of high-performance rectifiers.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (4) , 2809-2820
Collaborative Optimization Method for Wideband Transistor-Based Rectifiers With a Large Input Power Dynamic Range
This paper presents a collaborative optimization method for the design of wideband transistor-based rectifiers with a large input power dynamic range, targeting high-power energy harvesting and wireless power transfer applications. The core of the proposed method is to establish the relationship between the rectification efficiency, the continuous mode parameter,andthe input power range at several representative frequencies ofthecontinuous class-B/J mode, from which the target load impedance range under different frequencies and power levels is obtained. With the target impedance identified, an Ivy algorithm (IVYA)-driven intelligent optimization framework is then employed to enable the automated design and optimization of subsequent circuit topologies. To verify the proposed method, a wideband transistor-based rectifier operating from 2.2 to 2.6 GHz is designed, fabricated, and measured. The prototype achieves a peak efficiency of 63.5%–76.3% within the operating band, and maintains above 50% efficiency at a 17 dB input power back-off level, demonstrating the effectiveness and applicability of the proposed collaborative optimization method in the design of high-performance rectifiers.
- Open Access
- 15 August 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (8) , 938
Design of a Dual-Band Low-Noise Amplifier with a Novel Matching Structure
This paper proposes a method for designing a dual-band low-noise amplifier (DB-LNA) using a new improved complex impedance dual-band transformer (IDBT). This complex IDBT is composed of parallel-coupled lines and two sections of series microstrip lines. The parallel-coupled lines are used to complete the transformation from complex impedances at two different frequencies to a pair of conjugate complex impedances, meanwhile eliminating the need for DC blocking capacitors. The transformation to real impedances is achieved by series microstrip lines at dual frequency points. A single-stage DB-LNA was designed using the BFP840ESD transistor in combination with the proposed IDBT. The fabrication and testing of the Printed Circuit Board (PCB) were then completed. The measured results of the proposed 2.4/5.5 GHz DB-LNA show an S21 parameter of 20.3/14.7 dB, an S11 of −29.8/−20.3 dB, an S22 of −15.2/−16.4 dB, and a noise figure (NF) of 1.6/1.6 dB. The whole DB-LNA has a simple structure, low cost, and excellent performance and is easy to tune.
- 15 August 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (8) , 938
Open AccessDesign of a Dual-Band Low-Noise Amplifier with a Novel Matching Structure
This paper proposes a method for designing a dual-band low-noise amplifier (DB-LNA) using a new improved complex impedance dual-band transformer (IDBT). This complex IDBT is composed of parallel-coupled lines and two sections of series microstrip lines. The parallel-coupled lines are used to complete the transformation from complex impedances at two different frequencies to a pair of conjugate complex impedances, meanwhile eliminating the need for DC blocking capacitors. The transformation to real impedances is achieved by series microstrip lines at dual frequency points. A single-stage DB-LNA was designed using the BFP840ESD transistor in combination with the proposed IDBT. The fabrication and testing of the Printed Circuit Board (PCB) were then completed. The measured results of the proposed 2.4/5.5 GHz DB-LNA show an S21 parameter of 20.3/14.7 dB, an S11 of −29.8/−20.3 dB, an S22 of −15.2/−16.4 dB, and a noise figure (NF) of 1.6/1.6 dB. The whole DB-LNA has a simple structure, low cost, and excellent performance and is easy to tune.
- 8 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Consumer Electronics
- Vol. 71 (3) , 7683-7695
Investigation of the Effect of Phase Offset on GaN Transistor-Based Rectifiers and Its Application in Broadband Designs
This paper analyzes the effect of phase offset on transistor-based class-F, class-B/J, class-F-1 self-synchronous rectifiers. The relationship between rectification efficiency and phase shift is theoretically built for the first time, and the rectification efficiency under different phase offset conditions is obtained. By choosing appropriate phase offsets and continuous mode parameters, the high rectification efficiency can be obtained. Meanwhile the available impedance space is significantly expanded. Combination of the extended impedance space and the variable phase shift provides a novel approach for the design of broadband high-efficiency rectifiers. In addition, the frequency mapping methodology is proposed to satisfy this impedance space and phase shift range. For validation, a broadband high-efficiency class-F rectifier based on a GaN transistor is designed, fabricated, and tested. Experimental results demonstrate that the rectification efficiency of between 65.4% and 87.2% is realized in the frequency range of 1.6-3.0 GHz when the dc load Rdc=80 Y and the input power Pin=40 dBm. The proposed rectifier has the widest operation bandwidth among traditional transistor-based rectifiers.
- 8 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Consumer Electronics
- Vol. 71 (3) , 7683-7695
Investigation of the Effect of Phase Offset on GaN Transistor-Based Rectifiers and Its Application in Broadband Designs
This paper analyzes the effect of phase offset on transistor-based class-F, class-B/J, class-F-1 self-synchronous rectifiers. The relationship between rectification efficiency and phase shift is theoretically built for the first time, and the rectification efficiency under different phase offset conditions is obtained. By choosing appropriate phase offsets and continuous mode parameters, the high rectification efficiency can be obtained. Meanwhile the available impedance space is significantly expanded. Combination of the extended impedance space and the variable phase shift provides a novel approach for the design of broadband high-efficiency rectifiers. In addition, the frequency mapping methodology is proposed to satisfy this impedance space and phase shift range. For validation, a broadband high-efficiency class-F rectifier based on a GaN transistor is designed, fabricated, and tested. Experimental results demonstrate that the rectification efficiency of between 65.4% and 87.2% is realized in the frequency range of 1.6-3.0 GHz when the dc load Rdc=80 Y and the input power Pin=40 dBm. The proposed rectifier has the widest operation bandwidth among traditional transistor-based rectifiers.
- 6 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (11) , 8788-8800
A Generalized Design Approach for Dual-Band Class-F GaN HEMT-Based Rectifiers
In this article, a dual-band generalized class-F GaN HEMT-based high-efficiency rectifier is presented by employing inconstant conduction angle, phase shifts, and advanced optimization methodology. By building the relationship between the rectification efficiency of generalized continuous class-F mode and the continuous mode parameter, the phase offset parameter, and the conduction angle, it is found that high rectification efficiency can be maintained within two certain interval phase-shift amounts at a defined conduction angle. This eliminates the limitation of the dual-frequency transistor-based rectifier for a fixed phase shift and a constant conduction angle. Furthermore, the phase offset and the continuous mode parameters extend the load impedance space, leading to a wider operating bandwidth at two working frequency points. Moreover, advanced optimization methodology is employed to synthesize circuit networks to satisfy the desired phase shift and impedances. In order to verify the effectiveness of the proposed method, a dual-band high-efficiency transistor-based rectifier is designed. The test results indicate that the realized rectifier has an input power capacity of at least 10 W with peak rectification efficiencies of 85.6% and 84.6% at 1.7–1.9 and 3.1–3.3 GHz, respectively, when the gate voltage is −3.5 V and the dc load is $70~\Omega $ . To the best of authors’ knowledge, this work is the first to realize a dual-band (200-MHz bandwidth at two frequency points) transistor-based rectifier at two frequency points compared to the previous related works. Meanwhile, a more compact size is obtained.
- 6 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (11) , 8788-8800
A Generalized Design Approach for Dual-Band Class-F GaN HEMT-Based Rectifiers
In this article, a dual-band generalized class-F GaN HEMT-based high-efficiency rectifier is presented by employing inconstant conduction angle, phase shifts, and advanced optimization methodology. By building the relationship between the rectification efficiency of generalized continuous class-F mode and the continuous mode parameter, the phase offset parameter, and the conduction angle, it is found that high rectification efficiency can be maintained within two certain interval phase-shift amounts at a defined conduction angle. This eliminates the limitation of the dual-frequency transistor-based rectifier for a fixed phase shift and a constant conduction angle. Furthermore, the phase offset and the continuous mode parameters extend the load impedance space, leading to a wider operating bandwidth at two working frequency points. Moreover, advanced optimization methodology is employed to synthesize circuit networks to satisfy the desired phase shift and impedances. In order to verify the effectiveness of the proposed method, a dual-band high-efficiency transistor-based rectifier is designed. The test results indicate that the realized rectifier has an input power capacity of at least 10 W with peak rectification efficiencies of 85.6% and 84.6% at 1.7–1.9 and 3.1–3.3 GHz, respectively, when the gate voltage is −3.5 V and the dc load is $70~\Omega $ . To the best of authors’ knowledge, this work is the first to realize a dual-band (200-MHz bandwidth at two frequency points) transistor-based rectifier at two frequency points compared to the previous related works. Meanwhile, a more compact size is obtained.
- 31 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (11) , 1768-1771
Dual-Frequency Power Amplifiers’ Design Based on Improved Multiobjective Particle Swarm Optimization Algorithm
This article proposes an improved differential evolution multiobjective particle swarm optimization algorithm (DEV-MOPSO) for the design of dual-band power amplifiers (PAs). This algorithm enhances the global search capability during optimization by incorporating the concept of differential evolution. In addition, a hierarchical optimization strategy is used to optimize the multiobjective frequency bands of dual-band PAs according to their optimization priorities, achieving a multiband and efficient collaborative design. Measurement results demonstrate that the designed PA achieves a drain efficiency (DE) greater than 67%, an output power exceeding 40.2 dBm, and a gain higher than 10.2dB within the dual frequency bands of 2.3–2.5 and 3.2–3.4GHz. Meanwhile, the circuit transmission in the stopband is suppressed.
- 31 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (11) , 1768-1771
Dual-Frequency Power Amplifiers’ Design Based on Improved Multiobjective Particle Swarm Optimization Algorithm
This article proposes an improved differential evolution multiobjective particle swarm optimization algorithm (DEV-MOPSO) for the design of dual-band power amplifiers (PAs). This algorithm enhances the global search capability during optimization by incorporating the concept of differential evolution. In addition, a hierarchical optimization strategy is used to optimize the multiobjective frequency bands of dual-band PAs according to their optimization priorities, achieving a multiband and efficient collaborative design. Measurement results demonstrate that the designed PA achieves a drain efficiency (DE) greater than 67%, an output power exceeding 40.2 dBm, and a gain higher than 10.2dB within the dual frequency bands of 2.3–2.5 and 3.2–3.4GHz. Meanwhile, the circuit transmission in the stopband is suppressed.
- 8 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (10) , 1570-1573
Wideband Highly Efficient Extended Continuous Class-GF Power Amplifier Design Employing Modified Bagley-Polygon Four-Port Power Divider Architecture
A design of a broadband highly efficient power amplifier (PA) is presented in this letter. The novel design method proposed is to employ a modified Bagley-polygon four-port power divider (BPFPPD) architecture to fulfill wideband impedance matching of the PA and combine it with the load impedance space and source second harmonic manipulation space provided by the extended continuous class-GF (ECCGF) mode with a more flexible range to further improve the efficiency performance of the PA in broadband operation. To validate the presented design method, a wideband highly efficient PA operating from 0.5 to 3.7 GHz is designed and implemented through the use of commercially obtainable 10-W GaN HEMT devices. The measured results of the fabricated PA present 57%–71.4% drain efficiency (DE) and 8.9–11.8-dB gain with 38.9–41.8-dBm output power from the entire design bandwidth.
- 8 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (10) , 1570-1573
Wideband Highly Efficient Extended Continuous Class-GF Power Amplifier Design Employing Modified Bagley-Polygon Four-Port Power Divider Architecture
A design of a broadband highly efficient power amplifier (PA) is presented in this letter. The novel design method proposed is to employ a modified Bagley-polygon four-port power divider (BPFPPD) architecture to fulfill wideband impedance matching of the PA and combine it with the load impedance space and source second harmonic manipulation space provided by the extended continuous class-GF (ECCGF) mode with a more flexible range to further improve the efficiency performance of the PA in broadband operation. To validate the presented design method, a wideband highly efficient PA operating from 0.5 to 3.7 GHz is designed and implemented through the use of commercially obtainable 10-W GaN HEMT devices. The measured results of the fabricated PA present 57%–71.4% drain efficiency (DE) and 8.9–11.8-dB gain with 38.9–41.8-dBm output power from the entire design bandwidth.
- 24 April 2025
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 123 (3) , 1-8
A voltage reference implemented in GaAs pHEMT for SoC application
- 24 April 2025
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 123 (3) , 1-8
A voltage reference implemented in GaAs pHEMT for SoC application
- Open Access
- 25 December 2024
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Electronics Express
- Vol. 21 (24) , 20240596
S-C band wideband GaN power amplifier MMIC for radar application
In this letter, a broadband power amplifier ( PA ) monolithic microwave integrated circuit ( MMIC ) based on the 0.25 µm gallium nitride ( GaN ) high electron mobility transistor (HEMT) technology is presented for radar communication. The proposed PA is designed based on the optimal impedance area of the fundamental and second harmonic within the design frequency band acquired by multi-harmonic bilateral pull technique. It can be observed that good efficiency performance can still be expected when the second harmonic impedance includes the resistive-reactive with complex load impedances. As a verification, a wideband PA operating in the S-C band is implemented and measured. The results of measurement indicate that from 2-6 GHz, a saturated output power of 46.2-47.1 dBm, a power added efficiency ( PAE ) of 36.3% - 47 %, and a gain of 21.2-22.1 dB can be achieved under a drain voltage of 28V.
- 25 December 2024
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Electronics Express
- Vol. 21 (24) , 20240596
Open AccessS-C band wideband GaN power amplifier MMIC for radar application
In this letter, a broadband power amplifier ( PA ) monolithic microwave integrated circuit ( MMIC ) based on the 0.25 µm gallium nitride ( GaN ) high electron mobility transistor (HEMT) technology is presented for radar communication. The proposed PA is designed based on the optimal impedance area of the fundamental and second harmonic within the design frequency band acquired by multi-harmonic bilateral pull technique. It can be observed that good efficiency performance can still be expected when the second harmonic impedance includes the resistive-reactive with complex load impedances. As a verification, a wideband PA operating in the S-C band is implemented and measured. The results of measurement indicate that from 2-6 GHz, a saturated output power of 46.2-47.1 dBm, a power added efficiency ( PAE ) of 36.3% - 47 %, and a gain of 21.2-22.1 dB can be achieved under a drain voltage of 28V.