Metin Ozturk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Metin Ozturk has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Emre Tokuç
Bahcesehir University
5 shared publications - Nihan Altintas
Department of Electrical Engineering, Yildiz Technical University, Esenler, Istanbul 34220, Turkey
5 shared publications - Emrah Özsoy
Department of Urology, Ünye Çakırtepe Hospital, Ordu, Türkiye
4 shared publications M.I. Karaman
4 shared publications- Ridvan Kayar
Department of Urology, Haydarpasa Numune Training and Research Hospital, University of Health Sciences, ISTANBUL, Turkey
4 shared publications F. Ercan
3 shared publications
Latest Publications
- 16 August 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
A Novel Calculation Method for Half‐Bridge Series Resonant Inverter Circuits in Induction Cooker Designs
Induction heating (IH) technology is widely used in domestic cooking applications due to its speed, efficiency, and reliability. In IH cooktops, resonant inverter circuits are commonly preferred because of their soft‐switching capability. Among these topologies, the half‐bridge series resonant (HBSR) inverter is particularly suitable for applications requiring high performance and high power. This study proposes a new design methodology for HBSR inverters used in domestic IH cooktops. The method starts with user‐defined input parameters, including input power, input voltage, quality factor, and operating frequency. Unlike conventional approaches, the proposed model provides a simplified, verifiable, and practical calculation method for AC‐fed systems. Using the predefined input parameters, the method calculates the maximum power drawn from the source, the maximum and RMS coil currents, and the maximum current and voltage stresses of the semiconductor switch. Based on these values, the key resonant tank parameters, namely, equivalent resistance , equivalent inductance , and resonant capacitance , are determined. The calculated resonant circuit values were verified through both simulation and experimental implementation, confirming the accuracy and applicability of the proposed design methodology.
- 16 August 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
A Novel Calculation Method for Half‐Bridge Series Resonant Inverter Circuits in Induction Cooker Designs
Induction heating (IH) technology is widely used in domestic cooking applications due to its speed, efficiency, and reliability. In IH cooktops, resonant inverter circuits are commonly preferred because of their soft‐switching capability. Among these topologies, the half‐bridge series resonant (HBSR) inverter is particularly suitable for applications requiring high performance and high power. This study proposes a new design methodology for HBSR inverters used in domestic IH cooktops. The method starts with user‐defined input parameters, including input power, input voltage, quality factor, and operating frequency. Unlike conventional approaches, the proposed model provides a simplified, verifiable, and practical calculation method for AC‐fed systems. Using the predefined input parameters, the method calculates the maximum power drawn from the source, the maximum and RMS coil currents, and the maximum current and voltage stresses of the semiconductor switch. Based on these values, the key resonant tank parameters, namely, equivalent resistance , equivalent inductance , and resonant capacitance , are determined. The calculated resonant circuit values were verified through both simulation and experimental implementation, confirming the accuracy and applicability of the proposed design methodology.
- Open Access
- 19 May 2026
- Published by MDPI AG in Electronics
- Vol. 15 (10) , 2192
Generalized Positive/Negative Floating Impedance Multiplier Circuit and Its Application
Passive components in integrated circuits occupy significant areas and increase production costs, driving the demand for compact alternatives. This study presents a generalized, electronically controllable positive/negative floating impedance multiplier implemented in TSMC 180 nm CMOS technology. To achieve a compact layout, the architecture utilizes custom-designed operational transconductance amplifiers (OTAs). The circuit operates on a lossless principle, scaling resistance, capacitance, and inductance values within a wide multiplication range of −100 to +100 using only a single base element. Comprehensive LTspice simulations including PVT, Monte Carlo, THD, and noise analyses verify the design’s stable operation, low distortion, and favorable noise characteristics across various filter configurations. Furthermore, practical feasibility is validated through SPICE simulations using commercial LM13700 OTA, confirming consistent behavior for real-world applications. The proposed active topology occupies a compact core area of only 5831 μm2. By scaling down large passive components, this design decreases the overall system-level footprint, providing a versatile and area-efficient solution for tunable analog IC applications. It should be noted that the reported 5831 μm2 corresponds to the active core only, while the effective system-level area benefit depends on the selected base impedance and the target application.
- 19 May 2026
- Published by MDPI AG in Electronics
- Vol. 15 (10) , 2192
Open AccessGeneralized Positive/Negative Floating Impedance Multiplier Circuit and Its Application
Passive components in integrated circuits occupy significant areas and increase production costs, driving the demand for compact alternatives. This study presents a generalized, electronically controllable positive/negative floating impedance multiplier implemented in TSMC 180 nm CMOS technology. To achieve a compact layout, the architecture utilizes custom-designed operational transconductance amplifiers (OTAs). The circuit operates on a lossless principle, scaling resistance, capacitance, and inductance values within a wide multiplication range of −100 to +100 using only a single base element. Comprehensive LTspice simulations including PVT, Monte Carlo, THD, and noise analyses verify the design’s stable operation, low distortion, and favorable noise characteristics across various filter configurations. Furthermore, practical feasibility is validated through SPICE simulations using commercial LM13700 OTA, confirming consistent behavior for real-world applications. The proposed active topology occupies a compact core area of only 5831 μm2. By scaling down large passive components, this design decreases the overall system-level footprint, providing a versatile and area-efficient solution for tunable analog IC applications. It should be noted that the reported 5831 μm2 corresponds to the active core only, while the effective system-level area benefit depends on the selected base impedance and the target application.
- 27 February 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
Enhanced Design of Single‐Switch Quasi‐Resonant Inverters for Induction Heating
Induction heating (IH) systems are widely adopted in household appliances thanks to their energy efficiency and inherently safe operation. To maximize performance, resonant inverter circuits are frequently employed in IH applications due to their capability for soft‐switching and high efficiency. Among the various resonant inverter topologies, the single‐switch quasi‐resonant (SSQR) inverter stands out as a cost‐effective solution, particularly in systems with lower power requirements. However, this topology has a relatively limited soft‐switching range, and its stability can be affected by variations in the electrical characteristics of the load and the resonant circuit components. For optimal design and reliable performance, it is essential to precisely determine the values of the resonant capacitor and the induction coil, which are central components of SSQR‐based IH cookers. These parameters significantly influence the interaction between load behavior, resonant circuit characteristics, and safe operation boundaries. Moreover, in systems with closed‐loop control for power regulation and safety management, careful selection of resonant elements is fundamental to achieving both efficiency and reliability. This study introduces a refined design approach for SSQR inverters used in residential IH devices. The method's effectiveness is analyzed theoretically and validated through both simulations and prototype testing.
- 27 February 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
Enhanced Design of Single‐Switch Quasi‐Resonant Inverters for Induction Heating
Induction heating (IH) systems are widely adopted in household appliances thanks to their energy efficiency and inherently safe operation. To maximize performance, resonant inverter circuits are frequently employed in IH applications due to their capability for soft‐switching and high efficiency. Among the various resonant inverter topologies, the single‐switch quasi‐resonant (SSQR) inverter stands out as a cost‐effective solution, particularly in systems with lower power requirements. However, this topology has a relatively limited soft‐switching range, and its stability can be affected by variations in the electrical characteristics of the load and the resonant circuit components. For optimal design and reliable performance, it is essential to precisely determine the values of the resonant capacitor and the induction coil, which are central components of SSQR‐based IH cookers. These parameters significantly influence the interaction between load behavior, resonant circuit characteristics, and safe operation boundaries. Moreover, in systems with closed‐loop control for power regulation and safety management, careful selection of resonant elements is fundamental to achieving both efficiency and reliability. This study introduces a refined design approach for SSQR inverters used in residential IH devices. The method's effectiveness is analyzed theoretically and validated through both simulations and prototype testing.
- 22 December 2025
- Published by Springer Nature in Urolithiasis
- Vol. 54 (1) , 15
Predictive value of renal parenchyma and pelvic urine density on preoperative non-contrast CT in systemic inflammatory response syndrome (SIRS) after semi-rigid ureteroscopy
To evaluate the predictive value of preoperative NCCT (Non-Contrast Computed Tomography) measured renal parenchyma and pelvic urine densities for the development of systemic inflammatory response syndrome (SIRS) following URS. 1262 patients underwent semi-rigid URS due to ureterolithiasis between January 2008 and August 2023 were screened and 286 patients were included. Patient demographics and NCCT findings (stone size, location, density, hydronephrosis, renal parenchymal density, pelvic urine density) were collected retrospectively. Patients were categorized into two groups based on SIRS development after URS. Pelvic urine and parenchyma densities of the obstructed kidney were compared. A multivariate logistic regression analysis was performed to identify independent predictors of SIRS. The median obstructed kidney cortex mean density was significantly lower in the SIRS (+) group compared to the SIRS (-) group (26.67 [22.33–29.50] vs. 33.33 [27.24–37.75]). Obstructed kidney medulla mean density was also significantly lower in patients with SIRS (24.00 [22.33–27.50] vs. 31.50 [26.24–36.75], p = 0.001). Pelvic urine density was significantly higher in the SIRS-positive group. Stone density (OR = 1.35, % 95 CI: 1.09–1.67, p = 0.006), proximal ureteral location (OR = 5.21, % 95 CI: 1.84–14.7, p = 0.002), cortex mean density (OR = 0.91, % 95 CI: 0.87–0.95, p = 0.001) and pelvic urine density (OR = 1.07, % 95 CI: 1.02–1.12, p = 0.010) were stated as significant predictors. Renal parenchyma and pelvic urine density on pre-operative NCCT can predict SIRS after semi-rigid URS.
- 22 December 2025
- Published by Springer Nature in Urolithiasis
- Vol. 54 (1) , 15
Predictive value of renal parenchyma and pelvic urine density on preoperative non-contrast CT in systemic inflammatory response syndrome (SIRS) after semi-rigid ureteroscopy
To evaluate the predictive value of preoperative NCCT (Non-Contrast Computed Tomography) measured renal parenchyma and pelvic urine densities for the development of systemic inflammatory response syndrome (SIRS) following URS. 1262 patients underwent semi-rigid URS due to ureterolithiasis between January 2008 and August 2023 were screened and 286 patients were included. Patient demographics and NCCT findings (stone size, location, density, hydronephrosis, renal parenchymal density, pelvic urine density) were collected retrospectively. Patients were categorized into two groups based on SIRS development after URS. Pelvic urine and parenchyma densities of the obstructed kidney were compared. A multivariate logistic regression analysis was performed to identify independent predictors of SIRS. The median obstructed kidney cortex mean density was significantly lower in the SIRS (+) group compared to the SIRS (-) group (26.67 [22.33–29.50] vs. 33.33 [27.24–37.75]). Obstructed kidney medulla mean density was also significantly lower in patients with SIRS (24.00 [22.33–27.50] vs. 31.50 [26.24–36.75], p = 0.001). Pelvic urine density was significantly higher in the SIRS-positive group. Stone density (OR = 1.35, % 95 CI: 1.09–1.67, p = 0.006), proximal ureteral location (OR = 5.21, % 95 CI: 1.84–14.7, p = 0.002), cortex mean density (OR = 0.91, % 95 CI: 0.87–0.95, p = 0.001) and pelvic urine density (OR = 1.07, % 95 CI: 1.02–1.12, p = 0.010) were stated as significant predictors. Renal parenchyma and pelvic urine density on pre-operative NCCT can predict SIRS after semi-rigid URS.
- Open Access
- 12 December 2025
- Published by The Scientific and Technological Research Council of Turkey (TUBITAK-ULAKBIM) - DIGITAL COMMONS JOURNALS in TURKISH JOURNAL OF MEDICAL SCIENCES
- Vol. 55 (6) , 1459-1465
Predictive impact of PI-RADS 3 lesion volume/total prostate volume ratio in prostate cancer diagnosis in biopsy-naïve patients
Background/aim: To assess the potential of the ratio between PI-RADS 3 lesion volume and total prostate volume as a predictive parameter for guiding the decision to perform a biopsy in patients presenting with PI-RADS 3 lesions on multiparametric prostate magnetic resonance imaging (mpMRI). Materials and methods: A total of 749 patients who underwent mpMRI due to suspected prostate cancer between January 2014 and August 2023 were scanned. Based on predefined inclusion and exclusion criteria, 308 patients were included. Age, total prostate-specific antigen (PSA) value, prostate volume measured in mpMRI, mpMRI result, PI-RADS 3 lesion volume, and biopsy results were collected. The PI-RADS 3 ratio was calculated as PI-RADS 3 lesion volume/total prostate volume. PSA density (dPSA) was calculated. The patients were categorized according to their biopsy results as benign or malignant (subclassified by Gleason group grade), and the two groups were compared. Results: The average PI-RADS 3 ratio was 0.032 ± 0.002. There were 230 (74.7%) patients in the benign group and 78 (25.3%) patients in the malignant group. There was a statistically significant difference detected in average prostate volumes (p < 0.001), dPSA values (p = 0.001), and PI-RADS 3 ratios (p < 0.001). The receiver operating curve analysis of PI-RADS 3 ratio indicated an area under the curve of 0.643 ± 0.037. The optimal cut-off point was 0.026 with a sensitivity of 58.97% and a specificity of 66.96%. A positive, albeit weak, statistically significant relationship was found between PIRADS-3 ratios and dPSA values (rs ρ = 0.261 and p < 0.001). Conclusion: PI-RADS 3 ratio may serve as an auxiliary clinical parameter alongside age, dPSA, and lesion volume alone in identifying more refined candidates for biopsy in the goal of patient care individualization.
- 12 December 2025
- Published by The Scientific and Technological Research Council of Turkey (TUBITAK-ULAKBIM) - DIGITAL COMMONS JOURNALS in TURKISH JOURNAL OF MEDICAL SCIENCES
- Vol. 55 (6) , 1459-1465
Open AccessPredictive impact of PI-RADS 3 lesion volume/total prostate volume ratio in prostate cancer diagnosis in biopsy-naïve patients
Background/aim: To assess the potential of the ratio between PI-RADS 3 lesion volume and total prostate volume as a predictive parameter for guiding the decision to perform a biopsy in patients presenting with PI-RADS 3 lesions on multiparametric prostate magnetic resonance imaging (mpMRI). Materials and methods: A total of 749 patients who underwent mpMRI due to suspected prostate cancer between January 2014 and August 2023 were scanned. Based on predefined inclusion and exclusion criteria, 308 patients were included. Age, total prostate-specific antigen (PSA) value, prostate volume measured in mpMRI, mpMRI result, PI-RADS 3 lesion volume, and biopsy results were collected. The PI-RADS 3 ratio was calculated as PI-RADS 3 lesion volume/total prostate volume. PSA density (dPSA) was calculated. The patients were categorized according to their biopsy results as benign or malignant (subclassified by Gleason group grade), and the two groups were compared. Results: The average PI-RADS 3 ratio was 0.032 ± 0.002. There were 230 (74.7%) patients in the benign group and 78 (25.3%) patients in the malignant group. There was a statistically significant difference detected in average prostate volumes (p < 0.001), dPSA values (p = 0.001), and PI-RADS 3 ratios (p < 0.001). The receiver operating curve analysis of PI-RADS 3 ratio indicated an area under the curve of 0.643 ± 0.037. The optimal cut-off point was 0.026 with a sensitivity of 58.97% and a specificity of 66.96%. A positive, albeit weak, statistically significant relationship was found between PIRADS-3 ratios and dPSA values (rs ρ = 0.261 and p < 0.001). Conclusion: PI-RADS 3 ratio may serve as an auxiliary clinical parameter alongside age, dPSA, and lesion volume alone in identifying more refined candidates for biopsy in the goal of patient care individualization.
- Open Access
- 30 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 135476-135492
Design Methodology of Series Resonant Half Bridge Inverter for Induction Cooker
Induction heating is a commonly used method of heating in household appliances due to its efficiency and high reliability reasons. In induction cookers, resonant inverter circuits are frequently chosen due to their high efficiency and the ability to facilitate soft switching. Among the resonant inverters used in induction cookers, half-bridge series resonant (HBSR) inverter topology is often preferred for applications where a balance between cost and power is required. Despite the numerous circuit designs proposed to enhance the performance of HBSR converters, a standardized design methodology suitable for circuit design dedicated to induction cookers has not yet been established. In this study, a new HBSR inverter design methodology supported by various theoretical equations is proposed for use in household induction cooktops. In the proposed design, the first step involves calculating the equivalent resistance value of the coil. Subsequently, a coil capable of achieving to match this resistance value is designed mechanically. Finally, the capacitance value for the resonance circuit is calculated. Calculating the equivalent resistance value before designing the coil, in particular, enables the practical implementation of a viable coil design. To validate the proposed design methodology, it is necessary to control the power transferred to the resonant circuit. For this purpose, closed-loop power control is achieved using the peak value of coil current through frequency modulation technique. Additionally, it needs to be also proved that the implementation circuit works with soft switching between maximum and minimum switch cut-off current. To assess the compliance of the proposed design method with standards, thermal measurements were taken from semiconductors, EMC measurements were conducted to verify compliance with the IEC 55014-1 standard, and finally, the power transferred to the resonant circuit was calculated using oscilloscope measurements. Using the proposed design method, calculations were performed for a 20cm diameter iron pot with a 2300VA power transfer at 230VAC mains voltage. Subsequently, these calculations were verified using various simulation tools, and finally, a prototype implementation circuit was realized to demonstrate the reliability of the proposed design method.
- 30 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 135476-135492
Open AccessDesign Methodology of Series Resonant Half Bridge Inverter for Induction Cooker
Induction heating is a commonly used method of heating in household appliances due to its efficiency and high reliability reasons. In induction cookers, resonant inverter circuits are frequently chosen due to their high efficiency and the ability to facilitate soft switching. Among the resonant inverters used in induction cookers, half-bridge series resonant (HBSR) inverter topology is often preferred for applications where a balance between cost and power is required. Despite the numerous circuit designs proposed to enhance the performance of HBSR converters, a standardized design methodology suitable for circuit design dedicated to induction cookers has not yet been established. In this study, a new HBSR inverter design methodology supported by various theoretical equations is proposed for use in household induction cooktops. In the proposed design, the first step involves calculating the equivalent resistance value of the coil. Subsequently, a coil capable of achieving to match this resistance value is designed mechanically. Finally, the capacitance value for the resonance circuit is calculated. Calculating the equivalent resistance value before designing the coil, in particular, enables the practical implementation of a viable coil design. To validate the proposed design methodology, it is necessary to control the power transferred to the resonant circuit. For this purpose, closed-loop power control is achieved using the peak value of coil current through frequency modulation technique. Additionally, it needs to be also proved that the implementation circuit works with soft switching between maximum and minimum switch cut-off current. To assess the compliance of the proposed design method with standards, thermal measurements were taken from semiconductors, EMC measurements were conducted to verify compliance with the IEC 55014-1 standard, and finally, the power transferred to the resonant circuit was calculated using oscilloscope measurements. Using the proposed design method, calculations were performed for a 20cm diameter iron pot with a 2300VA power transfer at 230VAC mains voltage. Subsequently, these calculations were verified using various simulation tools, and finally, a prototype implementation circuit was realized to demonstrate the reliability of the proposed design method.
- Open Access
- 5 October 2023
- Published by MDPI AG in Electronics
- Vol. 12 (19) , 4145
A Simplified Design Method for Quasi-Resonant Inverter Used in Induction Hob
Induction heating (IH) technology is widely recognized and utilized in residential applications due to its high efficiency and safe operating characteristics. Resonant inverter circuits are widely used in IH systems because of their high efficiency and ability to perform soft switching. Among the various resonant inverters used in IH systems, the single-switch quasi-resonant (SSQR) inverter topology is typically preferred for low-cost and low-output-power applications. Despite its cost advantage, the SSQR topology has a relatively narrow soft-switching range, which can be unstable depending on the electrical parameters of the load and the resonant converter circuit. Accurately determining the capacitance value of the resonant capacitor and the inductance value of the induction coil, which are the key circuit elements of the SSQR induction cooker, is crucial for designing a reliable, efficient, and durable cooking system. In other words, there exists a critical relationship between the resonant converter circuit parameters, load characteristics, and safe operating conditions. Additionally, when considering closed-loop control methods used for power control and safety, selecting appropriate resonant circuit elements becomes vital in ensuring both reliable and efficient operation. This paper focuses on a novel and simplified design method for the SSQR inverter utilized in household appliances. The proposed method and its advantages in terms of the safe operating area of the switch are theoretically investigated and verified through simulations and prototype circuits.
- 5 October 2023
- Published by MDPI AG in Electronics
- Vol. 12 (19) , 4145
Open AccessA Simplified Design Method for Quasi-Resonant Inverter Used in Induction Hob
Induction heating (IH) technology is widely recognized and utilized in residential applications due to its high efficiency and safe operating characteristics. Resonant inverter circuits are widely used in IH systems because of their high efficiency and ability to perform soft switching. Among the various resonant inverters used in IH systems, the single-switch quasi-resonant (SSQR) inverter topology is typically preferred for low-cost and low-output-power applications. Despite its cost advantage, the SSQR topology has a relatively narrow soft-switching range, which can be unstable depending on the electrical parameters of the load and the resonant converter circuit. Accurately determining the capacitance value of the resonant capacitor and the inductance value of the induction coil, which are the key circuit elements of the SSQR induction cooker, is crucial for designing a reliable, efficient, and durable cooking system. In other words, there exists a critical relationship between the resonant converter circuit parameters, load characteristics, and safe operating conditions. Additionally, when considering closed-loop control methods used for power control and safety, selecting appropriate resonant circuit elements becomes vital in ensuring both reliable and efficient operation. This paper focuses on a novel and simplified design method for the SSQR inverter utilized in household appliances. The proposed method and its advantages in terms of the safe operating area of the switch are theoretically investigated and verified through simulations and prototype circuits.
- Open Access
- 29 August 2023
- Published by MDPI AG in Preprints.org
A Simplified Design Method for Quasi Resonant Inverter Used in Induction Hob
Induction heating (IH) technology is widely recognized and utilized in residential applications due to its high efficiency and safe operating characteristics. Resonant inverter circuits are widely used in IH systems because of their high efficiency and ability to perform soft-switching. Among the various resonant inverters used in IH systems, the single-switch quasi-resonant (SSQR) inverter topology is typically preferred for low-cost and low-output-power applications. Despite its cost advantage, the SSQR topology has a relatively narrow soft-switching range, which can be unstable depending on the electrical parameters of the load and the resonant converter circuit. Accurately determining the capacitance value of the resonant capacitor and the inductance value of the induction coil, which are the key circuit elements of the SSQR induction cooker, is crucial for designing a reliable, efficient, and durable cooking system. In other words, there exists a critical relationship between the resonant converter circuit parameters, load characteristics, and safe operating conditions. Additionally, when considering closed-loop control methods used for power control and safety, selecting appropriate resonant circuit elements becomes vital in ensuring both reliable and efficient operation. This paper focuses on a novel and simplified design method for the SSQR inverter utilized in household appliances. The proposed method and its advantages in terms of the safe operating area of the switch are theoretically investigated and verified through simulations and prototype circuits.
- 29 August 2023
- Published by MDPI AG in Preprints.org
Open AccessA Simplified Design Method for Quasi Resonant Inverter Used in Induction Hob
Induction heating (IH) technology is widely recognized and utilized in residential applications due to its high efficiency and safe operating characteristics. Resonant inverter circuits are widely used in IH systems because of their high efficiency and ability to perform soft-switching. Among the various resonant inverters used in IH systems, the single-switch quasi-resonant (SSQR) inverter topology is typically preferred for low-cost and low-output-power applications. Despite its cost advantage, the SSQR topology has a relatively narrow soft-switching range, which can be unstable depending on the electrical parameters of the load and the resonant converter circuit. Accurately determining the capacitance value of the resonant capacitor and the inductance value of the induction coil, which are the key circuit elements of the SSQR induction cooker, is crucial for designing a reliable, efficient, and durable cooking system. In other words, there exists a critical relationship between the resonant converter circuit parameters, load characteristics, and safe operating conditions. Additionally, when considering closed-loop control methods used for power control and safety, selecting appropriate resonant circuit elements becomes vital in ensuring both reliable and efficient operation. This paper focuses on a novel and simplified design method for the SSQR inverter utilized in household appliances. The proposed method and its advantages in terms of the safe operating area of the switch are theoretically investigated and verified through simulations and prototype circuits.
- Open Access
A Comparative Evaluation of Wide-Bandgap Semiconductors for High-Performance Domestic Induction Heating
This paper presents a comparative evaluation of wide-bandgap power semiconductor devices for domestic induction heating application, which is currently a serious alternative to traditional heating techniques. In the induction heating system, the power transferred to the output depends on the equivalent resistance of the load, and the resistance depends on the operating frequency. Due to the switching characteristics of wide-bandgap power semiconductor devices, an induction heating system can be operated at higher operating frequencies. In this study, SiC and Si semiconductor devices are used in the comparison. These devices are compared according to different evaluation issues such as the turn-off energy losses, turn-off times, current fall time, the power losses of the internal diodes, and the conduction voltage drops issues. To perform the proposed evaluation, the series-resonant half-bridge inverter, which is frequently used in state-of-the-art induction heating systems, has been selected. The device suitability in an induction heating system is analyzed with the help of a test circuit. A comparison is made in terms of criteria determined by using the selected switches in the experimental circuit, which is operated in the 200 W to 1800 W power range and 45 kHz to 125 kHz switching frequency range. System efficiency is measured as 97.3% when Si IGBT is used. In the case of using SiC cascode JFET, the efficiency of the system is increased up to 99%.
Open AccessA Comparative Evaluation of Wide-Bandgap Semiconductors for High-Performance Domestic Induction Heating
This paper presents a comparative evaluation of wide-bandgap power semiconductor devices for domestic induction heating application, which is currently a serious alternative to traditional heating techniques. In the induction heating system, the power transferred to the output depends on the equivalent resistance of the load, and the resistance depends on the operating frequency. Due to the switching characteristics of wide-bandgap power semiconductor devices, an induction heating system can be operated at higher operating frequencies. In this study, SiC and Si semiconductor devices are used in the comparison. These devices are compared according to different evaluation issues such as the turn-off energy losses, turn-off times, current fall time, the power losses of the internal diodes, and the conduction voltage drops issues. To perform the proposed evaluation, the series-resonant half-bridge inverter, which is frequently used in state-of-the-art induction heating systems, has been selected. The device suitability in an induction heating system is analyzed with the help of a test circuit. A comparison is made in terms of criteria determined by using the selected switches in the experimental circuit, which is operated in the 200 W to 1800 W power range and 45 kHz to 125 kHz switching frequency range. System efficiency is measured as 97.3% when Si IGBT is used. In the case of using SiC cascode JFET, the efficiency of the system is increased up to 99%.