Abasi Abudulimu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Abasi Abudulimu has a total of 206 co-authors. Here are the top co-authors by number of shared publications:
- Randy Ellingson
University of Toledo
21 shared publications - Yanfa Yan
University of Toledo
19 shared publications - Michael J. Heben
University of Toledo
14 shared publications - Adam B. Phillips
Wright Center for Photovoltaics Innovation & Commercialization and Department of Physics & Astronomy, University of Toledo 1 , Toledo, Ohio 43606
13 shared publications - Zhaoning Song
University of Toledo
12 shared publications Tyler Brau
University of Toledo
10 shared publications
Latest Publications
- Open Access
- 21 September 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (19) , 17043-17051
Tuning of Aromatic Amine Polymer Side chains for Application as Hole Transport Materials in Wide-Bandgap Perovskite Solar Cells
Perovskite solar cells (PSCs) hold strong potential for efficient and cost-effective photovoltaic technology, yet their device performance and stability remain hindered by interfacial limitations. In particular, the hole transport material (HTM) that contacts both the perovskite and the front contact can often be a bottleneck for device efficiency and durability. To overcome these challenges, we design and synthesize a series of carbazole- and fluorene-based polymers via palladium-catalyzed Buchwald–Hartwig amination, incorporating tunable N,N-dimethyl aminopropyl (N) and butanoate (COOCH3) side chains. We systematically investigate how these polar side chains affect the electronic properties of the buried perovskite interface and the overall device performance. Our results show that both N and COOCH3-functionalized HTMs significantly enhance interfacial compatibility with wide-bandgap perovskites, facilitating superior perovskite film formation and more efficient charge extraction. This enhancement yields wide-bandgap PSCs with a champion power conversion efficiency (PCE) of ∼17%, comparable to devices using commercial poly-triarylamine (PTAA) HTMs. These findings highlight that targeted side-chain engineering offers a simple and effective strategy to optimize polymer HTMs for wide-bandgap PSCs, providing valuable insights for the future design of perovskite optoelectronic devices.
- 21 September 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (19) , 17043-17051
Open AccessTuning of Aromatic Amine Polymer Side chains for Application as Hole Transport Materials in Wide-Bandgap Perovskite Solar Cells
Perovskite solar cells (PSCs) hold strong potential for efficient and cost-effective photovoltaic technology, yet their device performance and stability remain hindered by interfacial limitations. In particular, the hole transport material (HTM) that contacts both the perovskite and the front contact can often be a bottleneck for device efficiency and durability. To overcome these challenges, we design and synthesize a series of carbazole- and fluorene-based polymers via palladium-catalyzed Buchwald–Hartwig amination, incorporating tunable N,N-dimethyl aminopropyl (N) and butanoate (COOCH3) side chains. We systematically investigate how these polar side chains affect the electronic properties of the buried perovskite interface and the overall device performance. Our results show that both N and COOCH3-functionalized HTMs significantly enhance interfacial compatibility with wide-bandgap perovskites, facilitating superior perovskite film formation and more efficient charge extraction. This enhancement yields wide-bandgap PSCs with a champion power conversion efficiency (PCE) of ∼17%, comparable to devices using commercial poly-triarylamine (PTAA) HTMs. These findings highlight that targeted side-chain engineering offers a simple and effective strategy to optimize polymer HTMs for wide-bandgap PSCs, providing valuable insights for the future design of perovskite optoelectronic devices.
- Open Access
- 18 August 2026
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 8 (3) , 035009
Resilience of high-efficiency CdSeTe:As and CdSeTe:Cu solar cells to proton irradiation
Power generation in space is currently dominated by expensive III–V multi-junction photovoltaic (PV) devices and cheap crystalline silicon (c-Si) PV devices. Both of these technologies degrade rapidly in proton-radiation-rich space environments, such as the Van Allen belt. The present study of cadmium selenide telluride- (CdSeTe-) based PV devices exposed to 150-to-1500 keV proton irradiation with fluences up to 9 × 10 13 cm −2 reveal a more radiation-hard alternative to III–V and c-Si PV technologies. We report on measurement and analysis of current density vs voltage (JV), external quantum efficiency (EQE), external radiative efficiency, and capacitance vs voltage (CV) characteristics. JV characteristics of As-doped CdSeTe devices show 80% remaining power conversion efficiency (PCE) relative to unexposed controls when exposed to 650 keV protons at a fluence of 10 12 cm −2 . Under these same irradiation conditions, Cu-doped CdSeTe devices demonstrate an even better 95% PCE retention compared with unirradiated control devices. Evidence of radiation-induced absorber p-type doping compensation is observed in the glass-side EQE at 0 V and CV characteristics of most of the irradiated CdSeTe:As devices, but clear compensation is evident only for the most heavily irradiated CdSeTe:Cu devices. Elevated blue-green photocurrent in the film-side 0 V EQE suggests a buried junction in the most heavily irradiated CdSeTe:As devices. Although CdSeTe:Cu devices are the more resilient of the CdSeTe structures, both CdSeTe-based technologies are radiation-hard when compared to c-Si and III–V multi-junction PV.
- 18 August 2026
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 8 (3) , 035009
Open AccessResilience of high-efficiency CdSeTe:As and CdSeTe:Cu solar cells to proton irradiation
Power generation in space is currently dominated by expensive III–V multi-junction photovoltaic (PV) devices and cheap crystalline silicon (c-Si) PV devices. Both of these technologies degrade rapidly in proton-radiation-rich space environments, such as the Van Allen belt. The present study of cadmium selenide telluride- (CdSeTe-) based PV devices exposed to 150-to-1500 keV proton irradiation with fluences up to 9 × 10 13 cm −2 reveal a more radiation-hard alternative to III–V and c-Si PV technologies. We report on measurement and analysis of current density vs voltage (JV), external quantum efficiency (EQE), external radiative efficiency, and capacitance vs voltage (CV) characteristics. JV characteristics of As-doped CdSeTe devices show 80% remaining power conversion efficiency (PCE) relative to unexposed controls when exposed to 650 keV protons at a fluence of 10 12 cm −2 . Under these same irradiation conditions, Cu-doped CdSeTe devices demonstrate an even better 95% PCE retention compared with unirradiated control devices. Evidence of radiation-induced absorber p-type doping compensation is observed in the glass-side EQE at 0 V and CV characteristics of most of the irradiated CdSeTe:As devices, but clear compensation is evident only for the most heavily irradiated CdSeTe:Cu devices. Elevated blue-green photocurrent in the film-side 0 V EQE suggests a buried junction in the most heavily irradiated CdSeTe:As devices. Although CdSeTe:Cu devices are the more resilient of the CdSeTe structures, both CdSeTe-based technologies are radiation-hard when compared to c-Si and III–V multi-junction PV.
- Open Access
- 26 January 2026
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 11 (2) , 1696-1704
Radiative Defects in Chloride-Activated CdSe Thin Films
Defect recombination limits wide-gap Se-based chalcogenide devices, yet how chloride activation reshapes radiative pathways remains unclear. Here we show that a 40 min CdCl2 anneal converts evaporated CdSe from porous nanograins into dense micrometer-scale polycrystals and sharpens the optical band edge, reducing the Urbach energy from 85 to 17 meV at 300 K. Combining temperature- and fluence-dependent photoluminescence (PL), time-resolved PL, hyperspectral mapping, and hybrid-DFT, we resolve three emissive channels and identify their mechanisms. The near-edge band is excitonic at low temperature and evolves into free-carrier emission at elevated temperature. A sub-gap band at E g −0.45 eV requires above-gap carriers and thermally quenches with a 0.16 eV activation energy. A broad ∼1.05 eV infrared band is excited by above- and below-gap photons and retains microsecond lifetimes at room temperature; patial mapping links it to edge-rich microstructure. Calculations suggest selenium-vacancy and cadmium-vacancy–chlorine complexes, pointing to routes to suppress defect-related losses in wide-gap chalcogenide devices.
- 26 January 2026
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 11 (2) , 1696-1704
Open AccessRadiative Defects in Chloride-Activated CdSe Thin Films
Defect recombination limits wide-gap Se-based chalcogenide devices, yet how chloride activation reshapes radiative pathways remains unclear. Here we show that a 40 min CdCl2 anneal converts evaporated CdSe from porous nanograins into dense micrometer-scale polycrystals and sharpens the optical band edge, reducing the Urbach energy from 85 to 17 meV at 300 K. Combining temperature- and fluence-dependent photoluminescence (PL), time-resolved PL, hyperspectral mapping, and hybrid-DFT, we resolve three emissive channels and identify their mechanisms. The near-edge band is excitonic at low temperature and evolves into free-carrier emission at elevated temperature. A sub-gap band at E g −0.45 eV requires above-gap carriers and thermally quenches with a 0.16 eV activation energy. A broad ∼1.05 eV infrared band is excited by above- and below-gap photons and retains microsecond lifetimes at room temperature; patial mapping links it to edge-rich microstructure. Calculations suggest selenium-vacancy and cadmium-vacancy–chlorine complexes, pointing to routes to suppress defect-related losses in wide-gap chalcogenide devices.
- 5 November 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (46) , 63308-63321
How the Ge Incorporation Approach Affects Non-radiative Recombination Losses in CZTSSe Thin-Film Solar Cells
Kesterite-based thin-film solar cells (TFSCs) have regained attention in the photovoltaic community in recent times. However, their device performance still lags behind CdTe and Cu(In,Ga)Se2-based TFSCs because of dominant non-radiative recombination losses. The unstable nature of Sn ionic states is the main cause of poor performance. The present study employs the strategy of Ge doping at different positions in stacked metallic precursor layers and investigates real-time external radiative efficiency (ERE) mapping to clarify the role of Ge in kesterite-based compounds. The position of the Ge within the stacked metallic precursor shows distinct alloying behavior and variations in the density of Sn-related defects and associated defect clusters. Consequently, it offers improved grain growth and a reduced density of Sn-related deep-level defects in kesterite thin films. Furthermore, spatial ERE mapping reveals that the stacking order of the Ge significantly influences the average signal and uniformity of ERE. The Ge incorporation in metallic precursors results in an increased open-circuit voltage owing to significantly reduced non-radiative recombination. This study provides valuable insights into the assessment of non-radiative losses using a powerful tool, such as ERE, which assists in the development of these devices and contributes to achieving higher power conversion efficiency in TFSCs.
- 5 November 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (46) , 63308-63321
How the Ge Incorporation Approach Affects Non-radiative Recombination Losses in CZTSSe Thin-Film Solar Cells
Kesterite-based thin-film solar cells (TFSCs) have regained attention in the photovoltaic community in recent times. However, their device performance still lags behind CdTe and Cu(In,Ga)Se2-based TFSCs because of dominant non-radiative recombination losses. The unstable nature of Sn ionic states is the main cause of poor performance. The present study employs the strategy of Ge doping at different positions in stacked metallic precursor layers and investigates real-time external radiative efficiency (ERE) mapping to clarify the role of Ge in kesterite-based compounds. The position of the Ge within the stacked metallic precursor shows distinct alloying behavior and variations in the density of Sn-related defects and associated defect clusters. Consequently, it offers improved grain growth and a reduced density of Sn-related deep-level defects in kesterite thin films. Furthermore, spatial ERE mapping reveals that the stacking order of the Ge significantly influences the average signal and uniformity of ERE. The Ge incorporation in metallic precursors results in an increased open-circuit voltage owing to significantly reduced non-radiative recombination. This study provides valuable insights into the assessment of non-radiative losses using a powerful tool, such as ERE, which assists in the development of these devices and contributes to achieving higher power conversion efficiency in TFSCs.
- Open Access
- 3 October 2025
- Published by AIP Publishing in APL Energy
- Vol. 3 (4)
Proton radiation resilience of CdSeTe photovoltaics: High predicted end-of-life performance for space applications
Two types of cadmium selenide telluride (CdSeTe) photovoltaic devices have been exposed to high-energy (150–1500 keV) protons with fluences ranging from 1 × 1011 to 9 × 1013 cm−2. Pre- and post-irradiation current density vs voltage characteristic data were collected and analyzed. Arsenic-doped CdSeTe devices retained 80% of the power conversion efficiency (PCE) relative to control devices after exposure to 1012 cm−2 650 keV protons, while copper-doped CdSeTe devices retained about 95% of the control PCE under the same irradiation condition. Displacement damage dose analysis coupled with simulations for duration-dependent performance in a medium Earth orbit space mission revealed superior PCE remaining factors, indicating greater resilience to proton bombardment than state-of-the-art multijunction III-V based space photovoltaic technologies.
- 3 October 2025
- Published by AIP Publishing in APL Energy
- Vol. 3 (4)
Open AccessProton radiation resilience of CdSeTe photovoltaics: High predicted end-of-life performance for space applications
Two types of cadmium selenide telluride (CdSeTe) photovoltaic devices have been exposed to high-energy (150–1500 keV) protons with fluences ranging from 1 × 1011 to 9 × 1013 cm−2. Pre- and post-irradiation current density vs voltage characteristic data were collected and analyzed. Arsenic-doped CdSeTe devices retained 80% of the power conversion efficiency (PCE) relative to control devices after exposure to 1012 cm−2 650 keV protons, while copper-doped CdSeTe devices retained about 95% of the control PCE under the same irradiation condition. Displacement damage dose analysis coupled with simulations for duration-dependent performance in a medium Earth orbit space mission revealed superior PCE remaining factors, indicating greater resilience to proton bombardment than state-of-the-art multijunction III-V based space photovoltaic technologies.
- Open Access
- 3 October 2025
- Published by Springer Nature in Research Square
Radiative defects in chloride-activated CdSe thin films
Sub-gap recombination—not the intrinsic band structure—limits wide-gap Se-based chalcogenide devices, yet how chloride activation rewires radiative pathways has remained unclear. Here we show that a 30 min CdCl₂ anneal transforms evaporated CdSe from porous nanograins into dense micrometer-scale polycrystals and sharpens the optical band edge, reducing the Urbach energy from 85 to 17 meV at 300 K. Combining temperature- and fluence-dependent photoluminescence (PL), time-resolved PL and hyperspectral mapping with hybrid-DFT, we resolve three emissive channels and quantify their mechanisms. A near-edge band is excitonic at low temperature and becomes free-carrier emission above ∼120 K, with linewidth set by a ∼25 meV polar phonon. A sub-gap band at Eg–0.45 eV requires above-gap carriers and quenches with 0.16 eV. A broad ∼1.05 eV band is driven by both above- and below-gap photons, blue-shifts by ∼20 meV from 100–300 K and retains microsecond lifetimes at room temperature. Mapping links infrared emission to edge-rich microstructure where band-edge PL is dimmer, blue-shifted and broadened. Calculations are consistent with chlorine donors, a selenium-vacancy pathway for the sub-gap band, and a cadmium-vacancy–chlorine complex for the infrared band, pointing to concrete routes to suppress sub-gap loss in chalcogenide wide-gap photovoltaics and detectors.
- 3 October 2025
- Published by Springer Nature in Research Square
Open AccessRadiative defects in chloride-activated CdSe thin films
Sub-gap recombination—not the intrinsic band structure—limits wide-gap Se-based chalcogenide devices, yet how chloride activation rewires radiative pathways has remained unclear. Here we show that a 30 min CdCl₂ anneal transforms evaporated CdSe from porous nanograins into dense micrometer-scale polycrystals and sharpens the optical band edge, reducing the Urbach energy from 85 to 17 meV at 300 K. Combining temperature- and fluence-dependent photoluminescence (PL), time-resolved PL and hyperspectral mapping with hybrid-DFT, we resolve three emissive channels and quantify their mechanisms. A near-edge band is excitonic at low temperature and becomes free-carrier emission above ∼120 K, with linewidth set by a ∼25 meV polar phonon. A sub-gap band at Eg–0.45 eV requires above-gap carriers and quenches with 0.16 eV. A broad ∼1.05 eV band is driven by both above- and below-gap photons, blue-shifts by ∼20 meV from 100–300 K and retains microsecond lifetimes at room temperature. Mapping links infrared emission to edge-rich microstructure where band-edge PL is dimmer, blue-shifted and broadened. Calculations are consistent with chlorine donors, a selenium-vacancy pathway for the sub-gap band, and a cadmium-vacancy–chlorine complex for the infrared band, pointing to concrete routes to suppress sub-gap loss in chalcogenide wide-gap photovoltaics and detectors.
- Open Access
- 21 July 2025
- Published by Wiley in Advanced Energy Materials
Bias‐Dependent Quantum Efficiency Reveals Recombination Pathways in Thin Film Solar Cells
Identifying where recombination predominantly occurs—whether at the front interface, back interface, or throughout the bulk—is crucial for optimizing CdSeTe solar cells and many other photovoltaic device architectures. Here, a simple and effective diagnostic is demonstrated: measuring external quantum efficiency (QE) under varying forward biases. The drift–diffusion simulations reveal that each recombination pathway leaves a distinct bias‐induced signature in the normalized QE: a progressive drop at long wavelengths for back‐limited devices, a short‐wavelength decline for front‐limited devices, and a relatively uniform decrease across all wavelengths for bulk‐limited devices. These predictions are validated with experiments on As‐doped and Cu‐doped CdSeTe devices, with and without passivation layers or different front buffers. In each case, the observed bias‐dependent QE spectral changes align with the simulated recombination map. Because this method uses standard QE instrumentation, it offers a broadly accessible and cost‐efficient means to diagnose recombination pathways—extending beyond CdSeTe to other thin‐film and emerging solar cell technologies. By pinpointing recombination bottlenecks, researchers and manufacturers can strategically refine doping profiles, passivation schemes, and interface designs to further improve device performance.
- 21 July 2025
- Published by Wiley in Advanced Energy Materials
Open AccessBias‐Dependent Quantum Efficiency Reveals Recombination Pathways in Thin Film Solar Cells
Identifying where recombination predominantly occurs—whether at the front interface, back interface, or throughout the bulk—is crucial for optimizing CdSeTe solar cells and many other photovoltaic device architectures. Here, a simple and effective diagnostic is demonstrated: measuring external quantum efficiency (QE) under varying forward biases. The drift–diffusion simulations reveal that each recombination pathway leaves a distinct bias‐induced signature in the normalized QE: a progressive drop at long wavelengths for back‐limited devices, a short‐wavelength decline for front‐limited devices, and a relatively uniform decrease across all wavelengths for bulk‐limited devices. These predictions are validated with experiments on As‐doped and Cu‐doped CdSeTe devices, with and without passivation layers or different front buffers. In each case, the observed bias‐dependent QE spectral changes align with the simulated recombination map. Because this method uses standard QE instrumentation, it offers a broadly accessible and cost‐efficient means to diagnose recombination pathways—extending beyond CdSeTe to other thin‐film and emerging solar cell technologies. By pinpointing recombination bottlenecks, researchers and manufacturers can strategically refine doping profiles, passivation schemes, and interface designs to further improve device performance.
- Top Cited Papers
- 17 April 2025
- Published by Springer Nature in Nature Nanotechnology
- Vol. 20 (6) , 772-778
On-demand formation of Lewis bases for efficient and stable perovskite solar cells
In the fabrication of FAPbI3-based perovskite solar cells, Lewis bases play a crucial role in facilitating the formation of the desired photovoltaic α-phase. However, an inherent contradiction exists in their role: they must strongly bind to stabilize the intermediate δ-phase, yet weakly bind for rapid removal to enable phase transition and grain growth. To resolve this conflict, we introduced an on-demand Lewis base molecule formation strategy. This approach utilized Lewis-acid-containing organic salts as synthesis additives, which deprotonated to generate Lewis bases precisely when needed and could be reprotonated back to salts for rapid removal once their role is fulfilled. This method promoted the optimal crystallization of α-phase FAPbI3 perovskite films, ensuring the uniform vertical distribution of A-site cations, larger grain sizes and fewer voids at buried interfaces. Perovskite solar cells incorporating semicarbazide hydrochloride achieved an efficiency of 26.1%, with a National Renewable Energy Laboratory-certified quasi-steady-state efficiency of 25.33%. These cells retained 96% of their initial efficiency after 1,000 h of operation at 85 °C under maximum power point tracking. Additionally, mini-modules with an aperture area of 11.52 cm2 reached an efficiency of 21.47%. This strategy is broadly applicable to all Lewis-acid-containing organic salts with low acid dissociation constants and offers a universal approach to enhance the performance of perovskite solar cells and modules.
- 17 April 2025
- Published by Springer Nature in Nature Nanotechnology
- Vol. 20 (6) , 772-778
Top Cited PapersOn-demand formation of Lewis bases for efficient and stable perovskite solar cells
In the fabrication of FAPbI3-based perovskite solar cells, Lewis bases play a crucial role in facilitating the formation of the desired photovoltaic α-phase. However, an inherent contradiction exists in their role: they must strongly bind to stabilize the intermediate δ-phase, yet weakly bind for rapid removal to enable phase transition and grain growth. To resolve this conflict, we introduced an on-demand Lewis base molecule formation strategy. This approach utilized Lewis-acid-containing organic salts as synthesis additives, which deprotonated to generate Lewis bases precisely when needed and could be reprotonated back to salts for rapid removal once their role is fulfilled. This method promoted the optimal crystallization of α-phase FAPbI3 perovskite films, ensuring the uniform vertical distribution of A-site cations, larger grain sizes and fewer voids at buried interfaces. Perovskite solar cells incorporating semicarbazide hydrochloride achieved an efficiency of 26.1%, with a National Renewable Energy Laboratory-certified quasi-steady-state efficiency of 25.33%. These cells retained 96% of their initial efficiency after 1,000 h of operation at 85 °C under maximum power point tracking. Additionally, mini-modules with an aperture area of 11.52 cm2 reached an efficiency of 21.47%. This strategy is broadly applicable to all Lewis-acid-containing organic salts with low acid dissociation constants and offers a universal approach to enhance the performance of perovskite solar cells and modules.
- Open Access
- 20 December 2024
- Published by Elsevier in Cell Reports Physical Science
- Vol. 6 (1)
Enhanced understanding of recombination mechanisms in high-performance tin-lead perovskite solar cells
- 20 December 2024
- Published by Elsevier in Cell Reports Physical Science
- Vol. 6 (1)
Open AccessEnhanced understanding of recombination mechanisms in high-performance tin-lead perovskite solar cells