Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Andrés Villarruel-Jaramillo has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    System-Level Assessment Methodology for PV–AEL–H2–PEMFC Power-to-Power Systems: Constant-Efficiency Versus Quasi-Dynamic Modeling

    by Andrés Villarruel-Jaramillo, Freddy Nieto, Ignacio Arias, José M. Cardemil, Kenny Escobar-Segovia, Edgar Cando, Salvatore Reina

    Hydrogen-based power-to-power (PTP) systems complement batteries for long-duration storage, but their assessment often assumes fixed electrolyzer and fuel-cell efficiencies. The main innovation of this work is developing a system-level methodology to quantify how component-model fidelity affects the annual assessment of photovoltaic-alkaline electrolyzer-hydrogen-proton exchange membrane fuel cell systems. To highlight parameter and operational differences, two approaches are compared for the Santa Cruz–Baltra case study. Case A relies on simplified parameter assumptions, using fixed AEL and PEMFC efficiencies of 0.65 and 0.52. In contrast, Case B resolves operational differences by capturing operating-point-dependent electrochemical behavior, part-load variations, and AEL thermal-state propagation. Both cases use identical system boundaries and supervisory control, allowing model-fidelity effects on hydrogen production, storage utilization, and electricity recovery to be quantified. Annual simulations show that Case A predicts higher recovered electricity than Case B. For a representative configuration, global efficiency decreases from 0.529 to 0.440 (a 17% relative difference). The largest relative difference in recovered electricity (~91%) occurs in constrained configurations. Component-level experimental validation does not constitute full system-level validation. Overall, operating-point-dependent models materially alter annual PTP performance estimates under variable renewable operation.

  • Energy and economic performance evaluation of solar thermal and photovoltaic hybrid systems for industrial process heating

    by Josué F. Rosales-Pérez, Andrés Villarruel-Jaramillo, Manuel Pérez-García, José M. Cardemil, Rodrigo Escobar


  • Open Access

    Techno-economic evaluation of hybrid solar thermal and photovoltaic cooling systems in the industrial sector implementing a dynamic load estimation method

    by Andrés Villarruel-Jaramillo, Josué F. Rosales-Pérez, Manuel Pérez-García, José M. Cardemil, Rodrigo Escobar


  • Open Access

    Advancing the Industrial Sector Energy Transition with Hybrid Solar Systems: Evaluation of Small Winemaking in Ecuador

    by Andrés Villarruel-Jaramillo, Josué F. Rosales-Pérez, Manuel Pérez-García, José M. Cardemil, Rodrigo Escobar

    Ecuador may face an accelerated energy transition in the next 15 years due to the reduction of its oil reserves, affecting industries that require oil derivatives. To achieve a transition toward renewable energy without affecting the industry, this research proposed a technoeconomic evaluation of a hybrid system with solar flat plate collectors and photovoltaic modules that drive an absorption chiller and a compression chiller. The system supplies heat, cooling, and electricity to the winemaking industry in Ecuador. The best results for the hybrid systems reached a levelized cost of energy (LCOEn) of 0.171 USD/kWh and 0.157 USD/kWh in Guayaquil and Quito, respectively. For both locations, the LCOEn for the hybrid systems represents a decrease of the LCOEn of 53% and 32% concerning the individual solar photovoltaic and solar thermal systems, respectively. Therefore, the proposed hybrid system has a significant potential to integrate solar energy into the industry sector.

  • Open Access

    Techno-economic analysis of hybrid solar thermal systems with flat plate and parabolic trough collectors in industrial applications

    by Josué F. Rosales-Pérez, Andrés Villarruel-Jaramillo, Manuel Pérez-García, José M. Cardemil, Rodrigo Escobar


  • Open Access

    Modeling and Performance Evaluation of Hybrid Solar Cooling Systems Driven by Photovoltaic and Solar Thermal Collectors—Case Study: Greenhouses of Andalusia

    by Andrés Villarruel-Jaramillo, Josué F. Rosales-Pérez, Manuel Pérez-García, José M. Cardemil, Rodrigo Escobar

    Sustainable greenhouses have gained relevance in recent years due to their potential to reduce the carbon footprint of the agricultural sector by being integrated with renewable systems, contributing to the decarbonization of energy. Although solar technologies tend to be more accessible to cover the system’s energy demands, greenhouses are subject to installation area restrictions, limiting their energy potential. This research evaluates the energy advantages of hybridizing solar thermal collector fields with photovoltaic module fields to cover a greenhouse’s cooling and heating demands. For this purpose, the solar thermal field and the photovoltaic solar system were simulated with TRNSYS and MATLAB, respectively, while a method was developed to simulate the performance of a single-effect absorption chiller that was validated using the temperature measurements of a chiller in operation. The results show that the general method maintains differences between measurements and simulation smaller than 5% with set temperatures between 5.5 and 12 degrees Celsius. The hybrid system, with an air-to-water chiller as the main machine and absorption chiller, reached a solar fraction of 0.85 and a fractional energy saving of 83%. This represents a 27% reduction in area concerning an individual solar thermal system. This research highlights that the solar hybrid configuration reduces fossil energy consumption by improving the global efficiency of energy conversion, thereby reducing the area of the solar field.


  • Open Access

    Hybrid System of Photovoltaic and Solar Thermal Technologies for Industrial Process Heat

    by Josué F. Rosales-Pérez, Andrés Villarruel-Jaramillo, José A. Romero-Ramos, Manuel Pérez-García, José M. Cardemil, Rodrigo Escobar

    Process heating is the activity with the most energy consumption in the industrial sector. Solar heating (SH) systems are a promising alternative to provide renewable thermal energy to industrial processes. However, factors such as high investment costs and area limitations in industrial facilities hinder their utilization; therefore, hybrid systems that combine two different solar thermal or photovoltaic technologies where each technology operates under conditions that allow a higher overall performance than conventional configurations have been proposed. In this review, we discuss the limitations of conventional SH systems and the potential of hybrid configurations to overcome them. First, the current literature about conventional and hybrid systems is presented. Then, the application of common performance indicators to evaluate hybrid configurations is analyzed. Finally, the limitation, advantages, and potential applications of conventional and hybrid systems are discussed. This work shows that conventional systems are the most promising alternatives in low and high-temperature industrial applications. At the same time, in medium and processes, hybrid configurations have great potential to increase the performance of SH systems and help to boost their adoption in the industrial sector. There are few studies about hybrid systems in industrial applications, and further research is required to determine their potential.


  • Open Access

    Review of Polygeneration Schemes with Solar Cooling Technologies and Potential Industrial Applications

    by Andrés Villarruel-Jaramillo, Manuel Pérez-García, José M. Cardemil, Rodrigo A. Escobar

    The trend to reduce CO2 emissions in cooling processes has made it possible to increase the alternatives for integrating solar energy with thermal equipment whose viability depends on its adaptation to polygeneration schemes. Despite the enormous potential offered by the industry for cooling and heating processes, solar cooling technologies (SCT) have been explored in a limited way in the industrial sector. This work discusses the potential applications of industrial SCTs and classifies hybrid polygeneration schemes based on supplying cold, heat, electricity, and desalination of water; summarizes the leading SCTs, and details the main indicators of polygeneration configurations in terms of reductions on primary energy consumption and payback times. To achieve an energy transition in refrigeration processes, the scenarios with the most significant potential are: the food manufacturing industry (water immersion and crystallization processes), the beverage industry (fermentation and storage processes), and the mining industry (underground air conditioning).


  • Open Access

    Modelo computacional para reemplazar el material del refuerzo inferior de parachoques en preprototipado

    by Andrés Villarruel-Jaramillo, Juan Rocha-Hoyos, Edilberto Llanes-Cedeño, Javier Martinez-Gómez

    INTRODUCCIÓN. Se desarrolla un método computacional para la simulación dinámica del sistema de protección de peatones y análisis de cambio de material, con el fin de disminuir costos en pruebas que comúnmente requieren ensayos destructivos y, que dificultan el proceso de prototipado ante la necesidad de aumentar el número de piezas fabricadas en Ecuador. OBJETIVO. Validar un modelo de simulación computacional para reemplazo del material original del refuerzo inferior de parachoques del Kia Sportage R-2014 con materiales alternos. MÉTODO. El sistema fue digitalizado en el software Unigraphics NX, en base a la norma ACEA/2003/102/CE y el protocolo del Adendum 126: Regulación-N°127 de la ONU relativo a protección de peatones, los componentes fueron simulados con ayuda de Ansys Student usando 6 materiales alternos al original. RESULTADOS: La normativa de protección se cumple para todos los materiales, con excepción del ABS que supera los 200 g, mientras que el material con menor deformación y rotura es el PLA. DISCUSIÓN Y CONCLUSIONES: Dada las propiedades en deformación estructural, masa y aceleración en el impactador de piernas, se considera al PLA como el material con las características más cercanas al material original, mientras el policarbonato en caso de usar materiales disponibles en la industria ecuatoriana es el segundo material con las mejores propiedades, sin embargo, sufre una leve rotura en su zona frontal tras el impacto.