ZGZhenyu Gan

Zhenyu Gan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zhenyu Gan has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Gait transitions in load-pulling quadrupeds: insights from sled dogs and a minimal spring-loaded inverted pendulum model

    by Jiayu Ding, Benjamin Seleb, Heather J. Huson, Saad Bhamla, Zhenyu Gan

    Quadrupedal animals employ diverse galloping strategies to optimize speed, stability and energy efficiency. However, the biomechanical mechanisms that enable adaptive gait transitions during high-speed locomotion under load remain poorly understood. In this study, we present new empirical and modelling insights into the biomechanics of load-pulling quadrupeds, using sprint sled dogs as a model system. High-speed video and force recordings reveal that sled dogs often switch between rotary and transverse galloping gaits within just a few strides and with minimal changes in speed and stride duration, suggestive of locomotor multi-stability during high-speed load pulling. To investigate the mechanical basis of these transitions, a physics-based quadrupedal spring-loaded inverted pendulum (SLIP) model with hybrid dynamics and prescribed footfall sequences was used to reproduce the asymmetric galloping patterns observed in racing sled dogs. Through trajectory optimization, we replicate experimentally observed gait sequences and identify swing-leg stiffness modulation as a key control mechanism for inducing transitions. This work provides a much-needed biomechanical perspective on high-speed animal draft and establishes a modelling framework for studying locomotion in pulling quadrupeds, with implications for both biological understanding and the design of adaptive legged systems.

  • Energy-Optimal Asymmetrical Gait Selection for Quadrupedal Robots

    by Yasser G. Alqaham, Jing Cheng, Zhenyu Gan

    Symmetrical gaits, such as trotting, are commonly employed in quadrupedal robots for their simplicity and stability. However, the potential of asymmetrical gaits, such as bounding and galloping–which are prevalent in their natural counterparts at high speeds or over long distances–is less clear in the design of locomotion controllers for legged machines. This study systematically examines five distinct asymmetrical quadrupedal gaits on a legged robot, aiming to uncover the fundamental differences in footfall sequences and the consequent energetics across a broad range of speeds. Utilizing a full-body model of a quadrupedal robot (Unitree A1), we developed a hybrid system for each gait, incorporating the desired footfall sequence and rigid impacts. To identify the most energy-optimal gait, we applied optimal control methods, framing it as a trajectory optimization problem with specific constraints and a work-based cost of transport as an objective function. Our results show that, in the context of asymmetrical gaits, when minimizing cost of transport across the entire stride, the front leg pair primarily propels the system forward, while the rear leg pair acts more like an inverted pendulum, contributing significantly less to the energetic output. Additionally, while bounding–characterized by two aerial phases per cycle–is the most energy-optimal gait at higher speeds, the energy expenditure of gaits at speeds below 1 m/s depend heavily on the robot's specific design.


  • Breaking Symmetries Leads to Diverse Quadrupedal Gaits

    by Jiayu Ding, Zhenyu Gan

    Symmetry manifests itself in legged locomotion in a variety of ways: A legged system can maintain consistent gaits from any spatial starting point, exhibiting the same leg movements on either side of the torso in phase, and some even demonstrate forward and backward movements so similar they seem to reverse time. This work aims to generalize these phenomena and proposes formal definitions of symmetries in legged locomotion using terminology from group theory. In this research, we uncovered an intrinsic connection among a broad spectrum of quadrupedal gaits, which can be systematically identified via numerical continuations and distinguished by elements within a symmetry group. These gaits, within the hybrid dynamical system, are not merely isolated movements but part of a continuum, seamlessly transitioning from one to another at precise parameter bifurcation points. Altering specific symmetries at these junctures leads to the emergence of distinct gaits with unique footfall patterns, a phenomenon we've generalized through dimensional analysis in this study. Consequently, each gait manifests distinct preferred speed ranges and specific transition speeds. This work offers a comprehensive method to solve the gait generation problem for a quadruped, including pronking, two types of bounding, four variations of half-bounding, and two forms of galloping, and it also elucidates the mechanical rationale behind the necessity of gait transitions, providing high-level insight into the diversity and underlying mechanics of quadrupedal locomotion.


  • Open Access

    A Template Model Explains Jerboa Gait Transitions Across a Broad Range of Speeds

    by Jiayu Ding, Talia Y. Moore, Zhenyu Gan

    For cursorial animals that maintain high speeds for extended durations of locomotion, transitions between footfall patterns (gaits) predictably occur at distinct speed ranges. How do transitions among gaits occur for non-cursorial animals? Jerboas (Jaculus) are bipedal hopping rodents that frequently transition between gaits throughout their entire speed range. It has been hypothesized that these non-cursorial bipedal gait transitions are likely to enhance their maneuverability and predator evasion ability. However, it is difficult to use the underlying dynamics of these locomotion patterns to predict gait transitions due to the large number of degrees of freedom expressed by the animals. To this end, we used empirical jerboa kinematics and dynamics to develop a unified spring Loaded Inverted Pendulum model with defined passive swing leg motions. To find periodic solutions of this model, we formulated the gait search as a boundary value problem and described an asymmetrical running gait exhibited by the jerboas that emerged from the numerical search. To understand how jerboas change from one gait to another, we employed an optimization approach and used the proposed model to reproduce observed patterns of jerboa gait transitions. We then ran a detailed numerical study of the structure of gait patterns using a continuation approach in which transitions are represented by bifurcations. We found two primary mechanisms to increase the range of speeds at which gait transitions can occur. Coupled changes in the neutral leg swing angle alter leg dynamics. This mechanism generates changes in gait features (e.g., touchdown leg angle and timings of gait events) that have previously been shown to induce gait transitions. This mechanism slightly alters the speeds at which existing gait transitions occur. The model can also uncouple the left and right neutral leg swing angle, which generates asymmetries between left and right leg dynamics. New gait transitions emerge from uncoupled models across a broad range of speeds. In both the experimental observations and in the model, the majority of the gait transitions involve the skipping and asymmetrical running gaits generated by the uncoupled neutral leg swing angle mechanism. This simulated jerboa model is capable of systematically reproducing all biologically relevant gait transitions at a broad range of speeds.


  • All common bipedal gaits emerge from a single passive model

    by Zhenyu Gan, Yevgeniy Yesilevskiy, Petr Zaytsev, C. David Remy

    In this paper, we systematically investigate passive gaits that emerge from the natural mechanical dynamics of a bipedal system. We use an energetically conservative model of a simple spring-leg biped that exhibits well-defined swing leg dynamics. Through a targeted continuation of periodic motions of this model, we systematically identify different gaits that emerge from simple bouncing in place. We show that these gaits arise along one-dimensional manifolds that bifurcate into different branches with distinctly different motions. The branching is associated with repeated breaks in symmetry of the motion. Among others, the resulting passive dynamic gaits include walking, running, hopping, skipping and galloping. Our work establishes that the most common bipedal gaits can be obtained as different oscillatory motions (or nonlinear modes) of a single mechanical system with a single set of parameter values. For each of these gaits, the timing of swing leg motion and vertical motion is matched. This work thus supports the notion that different gaits are primarily a manifestation of the underlying natural mechanical dynamics of a legged system. Our results might explain the prevalence of certain gaits in nature, and may provide a blueprint for the design and control of energetically economical legged robots.


  • On the Dynamic Similarity Between Bipeds and Quadrupeds: A Case Study on Bounding

    by Zhenyu Gan, Ziyuan Jiao, C. David Remy

    In this paper, we identify passive dynamic bounding gaits of quadrupedal robots and investigate the dynamic similarities between these gaits and those of a bipedal model. For this purpose, we develop a passive dynamic bounding model of a quadruped with an extended main body. This model is based on the established SLIP model, yet has dynamic swing leg motions instead of a predefined angle of attack. We present a gait-identification framework that is based on a numerical continuation approach and that allows us to find all possible passive periodic motions that emerge from pronking and bounding in place. These gaits include forward pronking as well as forward bounding with gathered suspension, extended suspension, and with two suspensions. By conducting a parameter study on the body inertia, we can draw parallels between bipedal and quadrupedal gaits, and can also show how the structure of possible solutions changes with the main body inertia. In particular, we see sudden changes in the gait structure at certain critical values of the main body inertia. The work shows the connections between different types of quadrupedal gaits and may serve as a guideline in the design and control of gaits for energetically economical legged robots. It also sheds some light at the question why animals with different morphology use different gaits at the same Froude numbers.


  • Energy-Optimal Hopping in Parallel and Series Elastic One-Dimensional Monopeds

    by Yevgeniy Yesilevskiy, Zhenyu Gan, C. David Remy

    In this paper, we examine the question of whether parallel elastic actuation or series elastic actuation is better suited for hopping robots. To this end, we compare and contrast the two actuation concepts in energy optimal hopping motions. To enable a fair comparison, we employ optimal control to identify motion trajectories, actuator inputs, and system parameters that are optimally suited for each actuator concept. In other words, we compare the best possible hopper with parallel elastic actuation to the best possible hopper with series elastic actuation. The optimizations are conducted for three different cost functions: positive mechanical motor work, thermal electrical losses, and positive electrical work. Furthermore, we look at three representative cases for converting rotary motor motion to linear leg motion in a legged robot. Our model featured an electric DC-motor model, a gearbox with friction, damping in the leg spring, and contact collisions. We find that the optimal actuator choice depends both on the cost function and conversion of motor motion to leg motion. When considering only thermal electrical losses, parallel elastic actuation always performs better. In terms of positive mechanical motor work and positive electrical work, series elastic actuation is better when there is little friction in the gear-train. For higher gear-train friction parallel elastic actuation is more economical for these cost functions as well.


  • Toward Controllable Hydraulic Coupling of Joints in a Wearable Robot

    by Emma Treadway, Zhenyu Gan, C. David Remy, R. Brent Gillespie

    In this paper, we develop theoretical foundations for a new class of rehabilitation robot: body-powered devices that route power between a user's joints. By harvesting power from a healthy joint to assist an impaired joint, novel bimanual and self-assist therapies are enabled. This approach complements existing robotic therapies aimed at promoting recovery of motor function after neurological injury. We employ hydraulic transmissions for routing power, or equivalently for coupling the motions of a user's joints. Fluid power routed through flexible tubing imposes constraints within a limb or between homologous joints across the body. Variable transmissions allow constraints to be steered on the fly, and simple valve switching realizes free space and locked motion. We examine two methods for realizing variable hydraulic transmissions: using valves to switch among redundant cylinders (digital hydraulics) or using an intervening electromechanical link. For both methods, we present a rigorous mathematical framework for describing and controlling the resulting constraints. Theoretical developments are supported by experiments using a prototype fluid-power exoskeleton.


  • Optimal configuration of series and parallel elasticity in a 2D Monoped

    by Yevgeniy Yesilevskiy, Zhenyu Gan, C. David Remy

    This paper uses optimal control to simultaneously optimize the motion and morphology of a realistic model of a 2D Monoped. In particular, we compare the energetics of four different actuator configurations: a parallel elastic actuator (PEA) in the hip and a series elastic actuator in the leg (SEA), series hip and parallel leg, series hip and series leg, and parallel hip and parallel leg. We use realistic models with mass in the legs and feet, damping in the springs, and detailed DC electric motor models. The comparison is carried out for the cost of transport of three energetic measures: positive motor work, electrical losses, and positive electrical work, and evaluated as a function of velocity. In our optimization we include motor parameters, stiffness, and spring pre-compression terms as free variables, ensuring that we compare the energetically optimal version of each configuration at each velocity. We show that for the positive motor work and the electrical losses costs of transport (COT), the parallel hip and series leg configuration is energetically optimal. For the electrical work, the optimal configuration is speed dependent, with series hip and parallel leg optimal at low speeds, and both series hip series leg and parallel hip series leg optimal at high speeds.