Sunhyung Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sunhyung Kim has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Kyung Hyun Ahn
School of Chemical and Biological Engineering, and Institute of Chemical Processes, Seoul National University, Seoul, Republic of Korea
5 shared publications - Jeong Hoon Park
Seoul National University School of Chemical and Biological Engineering, Korea, Republic of (South Korea)
3 shared publications - Jun Dong Park
Department of Chemical and Biological Engineering, Sookmyung Women’s University, Seoul, Republic of Korea
2 shared publications - Sang Hoon Sung
School of Chemical and Biological Engineering, and Institute of Chemical Processes, Seoul National University, Seoul, 08826 Korea
2 shared publications - Byoung Soo Kim
Bio-convergence R&D Division, Korea, Institute of Ceramic Engineering and Technology (KICET), Chungbuk, Republic of Korea
1 shared publication Byung-Seok Lee
Korea Institute of Science and Technology
1 shared publication
Latest Publications
- 11 November 2026
- Published by American Chemical Society (ACS) in Langmuir
Understanding Microstructure Formation in Drying Nanoparticle–Polymer Films through Evolving Interparticle Interactions
The microstructure of nanoparticles in dried nanoparticle–polymer composite films influences their final properties and performance. However, a well-dispersed suspension does not always yield a uniform film, challenging the assumption that the initial dispersion state determines the microstructure of the dried film. We attribute this discrepancy to the evolution of interparticle interactions during drying. Brownian dynamics simulations were performed using a fixed interaction model (FIM) and an evolving interaction model (EIM). While the FIM showed limited agreement with the experimental trends, the EIM more closely reproduced the reported uniform structure at pH 3 and a heterogeneous structure at pH 10, despite the contrasting initial dispersion states. This results from interaction evolution governed by particle–polymer affinity, becoming more repulsive under good affinity (pH 3) and more attractive under poor affinity (pH 10). The drying rate, characterized by the Peclet number (Pe), further governs the influence of evolved interactions, with low Pe enabling rearrangement and high Pe increasingly preserving the initial structure. These results demonstrate that understanding microstructure formation in nanoparticle–polymer films requires consideration of the evolution of interparticle interactions beyond conventional drying kinetics.
- 11 November 2026
- Published by American Chemical Society (ACS) in Langmuir
Understanding Microstructure Formation in Drying Nanoparticle–Polymer Films through Evolving Interparticle Interactions
The microstructure of nanoparticles in dried nanoparticle–polymer composite films influences their final properties and performance. However, a well-dispersed suspension does not always yield a uniform film, challenging the assumption that the initial dispersion state determines the microstructure of the dried film. We attribute this discrepancy to the evolution of interparticle interactions during drying. Brownian dynamics simulations were performed using a fixed interaction model (FIM) and an evolving interaction model (EIM). While the FIM showed limited agreement with the experimental trends, the EIM more closely reproduced the reported uniform structure at pH 3 and a heterogeneous structure at pH 10, despite the contrasting initial dispersion states. This results from interaction evolution governed by particle–polymer affinity, becoming more repulsive under good affinity (pH 3) and more attractive under poor affinity (pH 10). The drying rate, characterized by the Peclet number (Pe), further governs the influence of evolved interactions, with low Pe enabling rearrangement and high Pe increasingly preserving the initial structure. These results demonstrate that understanding microstructure formation in nanoparticle–polymer films requires consideration of the evolution of interparticle interactions beyond conventional drying kinetics.
- 1 December 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (12)
Yielding behavior of concentrated lithium-ion battery anode slurry
The nonlinear rheology of a concentrated lithium-ion battery anode slurry was examined under large amplitude oscillatory shear and interpreted with a sequence of physical process (SPP) analysis. A complex interplay of three anode slurry components—graphite (Gr) as an active material, carbon black (CB) as a conductive additive, and carboxymethyl cellulose (CMC) as a binder—leads to a two-step yielding behavior, represented as the secondary plateau in dynamic strain and stress sweep tests. We demonstrate that a two-step yielding behavior is manifested as double deltoids in SPP analysis through the study of intra-cycle rheological transition under oscillatory shear flow. Slurries of Gr-CMC exhibit the two-step yielding behavior; slurries of CB-CMC do not, suggesting that Gr and CMC are the primary causes of two-step yielding in an anode slurry. A sedimentation test on a dilute Gr-CMC solution yielded phase separation between graphite particles, with CMC adsorbed on their surface and graphite particles aggregated via hydrophobic attraction. This indicates two possible types of interactions in a concentrated slurry: a hydrophobic interaction between graphite particles and a physicochemical interaction caused by CMC adsorbed on graphite particles. The first yielding step relates to the hydrophobic attraction between graphite particles, resulting in a network structure that is expected to be brittle and rupture at a small strain. The second yielding step is attributed to the interaction between concentrated CMC, which is corroborated by the overlap of the secondary deltoid of the anode slurry and the single deltoid of the concentrated CMC solution in SPP analysis.
- 1 December 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (12)
Yielding behavior of concentrated lithium-ion battery anode slurry
The nonlinear rheology of a concentrated lithium-ion battery anode slurry was examined under large amplitude oscillatory shear and interpreted with a sequence of physical process (SPP) analysis. A complex interplay of three anode slurry components—graphite (Gr) as an active material, carbon black (CB) as a conductive additive, and carboxymethyl cellulose (CMC) as a binder—leads to a two-step yielding behavior, represented as the secondary plateau in dynamic strain and stress sweep tests. We demonstrate that a two-step yielding behavior is manifested as double deltoids in SPP analysis through the study of intra-cycle rheological transition under oscillatory shear flow. Slurries of Gr-CMC exhibit the two-step yielding behavior; slurries of CB-CMC do not, suggesting that Gr and CMC are the primary causes of two-step yielding in an anode slurry. A sedimentation test on a dilute Gr-CMC solution yielded phase separation between graphite particles, with CMC adsorbed on their surface and graphite particles aggregated via hydrophobic attraction. This indicates two possible types of interactions in a concentrated slurry: a hydrophobic interaction between graphite particles and a physicochemical interaction caused by CMC adsorbed on graphite particles. The first yielding step relates to the hydrophobic attraction between graphite particles, resulting in a network structure that is expected to be brittle and rupture at a small strain. The second yielding step is attributed to the interaction between concentrated CMC, which is corroborated by the overlap of the secondary deltoid of the anode slurry and the single deltoid of the concentrated CMC solution in SPP analysis.
- 25 January 2022
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 61 (5) , 2100-2109
Significant Agglomeration of Conductive Materials and the Dispersion State Change of the Ni-Rich NMC-Based Cathode Slurry during Storage
- 25 January 2022
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 61 (5) , 2100-2109
Significant Agglomeration of Conductive Materials and the Dispersion State Change of the Ni-Rich NMC-Based Cathode Slurry during Storage
- 16 March 2021
- Published by Society of Rheology in Journal of Rheology
- Vol. 65 (3) , 337-354
Brownian dynamics simulation on orthogonal superposition rheology: Time–shear rate superposition of colloidal gel
The dynamics of model colloidal gels under a steady shear flow is studied by means of a Brownian dynamics (BD) simulation while applying orthogonal superposition rheometry, which superimposes a small amplitude oscillatory flow orthogonal to the main flow direction. Orthogonal dynamic frequency sweep (ODFS) curves are obtained at various magnitudes of the main flow, which shows shear thinning behavior of the colloidal gel. The viscoelastic spectra of the ODFS can be superimposed onto a master curve by the horizontal shift factor, which is equivalent to particle viscosity. That is, the shear rate controls a single master clock for all viscoelastic spectra of the ODFS in the form of a time–shear rate superposition, which bears an analogy with the time–temperature superposition of polymeric systems. In the low-frequency region of the master curve, both orthogonal moduli are well superimposed onto a single master curve, whereas the loss modulus deviates slightly from the master curve in the high-frequency region, which coincides with the experimental findings. We observe spatial and time-varying structural properties in both low- and high-frequency regions on the ODFS curves by decomposing the pair distribution function. It is verified that each flow condition shifted onto the same stress level on the master curve shows identical spatial orthogonal moduli at all radial distances despite the differences in the aggregate size and average particle connectivity.
- 16 March 2021
- Published by Society of Rheology in Journal of Rheology
- Vol. 65 (3) , 337-354
Brownian dynamics simulation on orthogonal superposition rheology: Time–shear rate superposition of colloidal gel
The dynamics of model colloidal gels under a steady shear flow is studied by means of a Brownian dynamics (BD) simulation while applying orthogonal superposition rheometry, which superimposes a small amplitude oscillatory flow orthogonal to the main flow direction. Orthogonal dynamic frequency sweep (ODFS) curves are obtained at various magnitudes of the main flow, which shows shear thinning behavior of the colloidal gel. The viscoelastic spectra of the ODFS can be superimposed onto a master curve by the horizontal shift factor, which is equivalent to particle viscosity. That is, the shear rate controls a single master clock for all viscoelastic spectra of the ODFS in the form of a time–shear rate superposition, which bears an analogy with the time–temperature superposition of polymeric systems. In the low-frequency region of the master curve, both orthogonal moduli are well superimposed onto a single master curve, whereas the loss modulus deviates slightly from the master curve in the high-frequency region, which coincides with the experimental findings. We observe spatial and time-varying structural properties in both low- and high-frequency regions on the ODFS curves by decomposing the pair distribution function. It is verified that each flow condition shifted onto the same stress level on the master curve shows identical spatial orthogonal moduli at all radial distances despite the differences in the aggregate size and average particle connectivity.
- Open Access
Role of PVDF in Rheology and Microstructure of NCM Cathode Slurries for Lithium-Ion Battery
A binder plays a critical role in dispersion of coating liquids and the quality of coating. Poly(vinylidene fluoride) (PVDF) is widely used as a binder in cathode slurries; however, its role as a binder is still under debate. In this paper, we study the role of PVDF on the rheology of cathode battery slurries consisting of Li(Ni1/3Mn1/3Co1/3)O2 (NCM), carbon black (CB) and N-methyl-2-pyrrolidone (NMP). Rheology and microstructure of cathode slurries are systemically investigated with three model suspensions: CB/PVDF/NMP, NCM/PVDF/NMP and NCM/CB/PVDF/NMP. To highlight the role of PVDF in cathode slurries, we prepare the same model suspensions by replacing PVDF with PVP, and we compare the role of PVDF to PVP in the suspension rheology. We find that PVDF adsorbs neither onto NCM nor CB surface, which can be attributed to its poor affinity to NCM and CB. Rheological measurements suggest that PVDF mainly increases matrix viscosity in the suspension without affecting the microstructure formed by CB and NCM particles. In contrast to PVDF, PVP stabilizes the structure of CB and NCM in the model suspensions, as it is adsorbed on the CB surface. This study will provide a useful insight to fundamentally understand the rheology of cathode slurries.
Open AccessRole of PVDF in Rheology and Microstructure of NCM Cathode Slurries for Lithium-Ion Battery
A binder plays a critical role in dispersion of coating liquids and the quality of coating. Poly(vinylidene fluoride) (PVDF) is widely used as a binder in cathode slurries; however, its role as a binder is still under debate. In this paper, we study the role of PVDF on the rheology of cathode battery slurries consisting of Li(Ni1/3Mn1/3Co1/3)O2 (NCM), carbon black (CB) and N-methyl-2-pyrrolidone (NMP). Rheology and microstructure of cathode slurries are systemically investigated with three model suspensions: CB/PVDF/NMP, NCM/PVDF/NMP and NCM/CB/PVDF/NMP. To highlight the role of PVDF in cathode slurries, we prepare the same model suspensions by replacing PVDF with PVP, and we compare the role of PVDF to PVP in the suspension rheology. We find that PVDF adsorbs neither onto NCM nor CB surface, which can be attributed to its poor affinity to NCM and CB. Rheological measurements suggest that PVDF mainly increases matrix viscosity in the suspension without affecting the microstructure formed by CB and NCM particles. In contrast to PVDF, PVP stabilizes the structure of CB and NCM in the model suspensions, as it is adsorbed on the CB surface. This study will provide a useful insight to fundamentally understand the rheology of cathode slurries.
- 19 July 2019
- Published by Springer Nature in Journal of Materials Science
- Vol. 54 (20) , 13208-13220
Effect of neutralization of poly(acrylic acid) binder on the dispersion heterogeneity of Li-ion battery electrodes
- 19 July 2019
- Published by Springer Nature in Journal of Materials Science
- Vol. 54 (20) , 13208-13220
Effect of neutralization of poly(acrylic acid) binder on the dispersion heterogeneity of Li-ion battery electrodes
- 1 August 2011
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2011-02 (16) , 890
Effect of Nafion Ionomer and Catalyst in Cathode Layers for the Direct Formic Acid Fuel Cell with Complex Capacitance Analysis on the Ionic Resistance
- 1 August 2011
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2011-02 (16) , 890
Effect of Nafion Ionomer and Catalyst in Cathode Layers for the Direct Formic Acid Fuel Cell with Complex Capacitance Analysis on the Ionic Resistance
- 1 December 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2 (21531447) , 86-89
Development of Home Network Gateway Supporting both Wire and Wireless Communication
A home network gateway has been developed, which supports both wire and wireless communication functions. ZigBee and PLC modules are taken as communication hardware and a conversion protocol is implemented to be able to smoothly exchange the information between the two hardware modules. The developed gateway shows good performance and can supports various home network service configurations.
- 1 December 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2 (21531447) , 86-89
Development of Home Network Gateway Supporting both Wire and Wireless Communication
A home network gateway has been developed, which supports both wire and wireless communication functions. ZigBee and PLC modules are taken as communication hardware and a conversion protocol is implemented to be able to smoothly exchange the information between the two hardware modules. The developed gateway shows good performance and can supports various home network service configurations.