Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ahmed Atef Bakhsh has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Chemical design and characterization of fluoropolymer-silica nanocomposite superhydrophobic coating for durable and self-cleaning photovoltaic cells

    by Ahmed A. Bakhsh

    Dust accumulation on photovoltaic (PV) solar panels significantly reduces the efficiency of energy conversion. Thus, innovative surface modifications are needed to mitigate soiling and enhance durability. This study presents the development of a robust polymer-based superhydrophobic coating designed to minimize dust adhesion while maintaining PV performance. The coating formulation integrates polyvinylidene fluoride (PVDF) as a hydrophobic matrix with superhydrophobic silica nanoparticles (SiO₂) to achieve optimal surface properties. The optimized composition, consisting of 2 wt% PVDF and 35 wt% SiO₂, exhibited a high-water contact angle of 155.8°, confirming its superior hydrophobicity. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) analyses revealed a rough hierarchical structure, which is a key factor in achieving superhydrophobicity. Mechanical durability was validated through peel tests, demonstrating strong adhesion and long-term stability. PV performance analysis of silicon solar cells coated with the developed material showed no reduction in power output, confirming its compatibility with solar energy applications. These findings highlight the potential of the proposed superhydrophobic coating to enhance the efficiency and longevity of PV panels in real-world conditions, addressing critical challenges in solar energy deployment.

  • Open Access

    Optimization of Polyolefin-Bonded Hydroxyapatite Graphite for Sustainable Industrial Applications

    by Ahmed A. Bakhsh

    As a means of introducing environmental responsibility to industrial applications, the usage of biobased composite materials has been encouraged in recent years. Polymer nanocomposites utilize polyolefins increasingly as a matrix, owing to the diversity in their features and prospective applications, even though typical polyester blend materials, such as glass and composite materials, have garnered greater attention from researchers. The mineral hydroxy-apatite, or Ca10(PO4)6(OH)2, is the primary structural component of bone and tooth enamel. Increased bone density and strength result from this procedure. As a result, nanohms are fabricated from eggshells into rods with very tiny particle sizes. Although there have been many papers written on the benefits of HA-loaded polyolefins, the reinforcing effect of HA at low loadings has not yet been taken into account. The purpose of this work was to examine the mechanical and thermal characteristics of polyolefin-HA nanocomposites. These nanocomposites were built out of HDPE and LDPE (LDPE). As an extension of this work, we investigated what would happen when HA is added to LDPE composites at concentrations as high as 40% by weight. Carbonaceous fillers, including graphene, carbon nanotubes, carbon fibers, and exfoliated graphite, all play significant roles in nanotechnology owing to the extraordinary enhancements in their thermal, electrical, mechanical, and chemical properties. The purpose of this study was to examine the effects of adding a layered filler, such as exfoliated graphite (EG), to microwave zones that might have real-world applications for their mechanical, thermal, and electrical characteristics. Mechanical and thermal properties were significantly enhanced by the incorporation of HA, notwithstanding a minor decrease in these attributes at a loading of 40% HA by weight. A higher load-bearing capability of LLDPE matrices suggests their potential usage in biological contexts.


  • Open Access

    Applications of Discrete Wavelet Transform for Feature Extraction to Increase the Accuracy of Monitoring Systems of Liquid Petroleum Products

    by Mohammed Balubaid, Mohammad Amir Sattari, Osman Taylan, Ahmed A. Bakhsh, Ehsan Nazemi

    This paper presents a methodology to monitor the liquid petroleum products which pass through transmission pipes. A simulation setup consisting of an X-ray tube, a detector, and a pipe was established using a Monte Carlo n-particle X-version transport code to investigate a two-by-two mixture of four different petroleum products, namely, ethylene glycol, crude oil, gasoline, and gasoil, in deferent volumetric ratios. After collecting the signals of each simulation, discrete wavelet transform (DWT) was applied as the feature extraction system. Then, the statistical feature, named the standard deviation, was calculated from the approximation of the fifth level, and the details of the second to fifth level provide appropriate inputs for neural network training. Three multilayer perceptron neural networks were utilized to predict the volume ratio of three types of petroleum products, and the volume ratio of the fourth product could easily be obtained from the results of the three presented networks. Finally, a root mean square error of less than 1.77 was obtained in predicting the volume ratio, which was much more accurate than in previous research. This high accuracy was due to the use of DWT for feature extraction.


  • Open Access

    Gamma-Ray Modified Polymer/Clay Composites: Synthesis, Characterization, and Formulation Optimization Using Multivariate Calculus and Graph Theory

    by Ahmed A. Bakhsh

    To enhance the oxidation strength and crosslinking yield of ultrahigh molecular weight polyethylene (UHMWPE), its composites were prepared by mixing 1%, 2%, and 3% (by wt.) of magnesium silicate hydrous (sepiolite) during this study. These composites were irradiated with 25 kGy and 50 kGy of irradiation doses in the open air. Subsequent to irradiation, the composites were characterized for updates in structure, oxidation strength, and degree of crosslinking while estimating the values of oxidation index (OI), crosslink density (Gx), and percent crystallinity (Xc), respectively. The reaction of modified sepiolite (SP) on irradiating UHMWPE/SP composites was evident from the origination of peaks at Si-O, O-Si-O, Si-O-Si, and Mg-OH and stretching vibration at 974 cm−1, 1014 cm−1, and 1080 cm−1, respectively. In addition, the moderate negative correlation of OI (−0.46) and strong positive correlation of Gx (0.87) with the absorbed dose, made obvious from correlation analysis, confirmed the effectiveness of SP in enhancing the oxidation strength and crosslink density of UHMWPE. Furthermore, cluster analysis (CA) grouped the composites as low, moderate, and best based on dissimilarities, i.e., oxidation strength and crosslink density, which was further confirmed by principal component analysis (PCA). PCA also revealed that the OI, Gx, and absorbed dose were the active variables for this best group. After confirming the effectiveness of SP (as an active filler for enhancing the oxidation strength and crosslink density of UHMWPE) and recognizing the OI, Gx, and absorbed dose as active variables, the next step was to determine the necessary minimum amount of SP concentration and radiation dose required for the composite that outperforms all others. For this, a parametric graph theory and matrix approach was employed to rank the composites of the best group, revealing that the UHMWPE/SP composite with 1% (by wt.) of Si12O30Mg8(OH)4(H2O)4·8H2O and irradiated with 50 kGy of irradiation dose was the most suitable choice of all existing alternatives tested in this study. Although this is the first attempt, to the best of our knowledge, where a smart approach using multivariate calculus and decision-making tools was utilized for figuring the best UHMWPE composite formulation along with appropriate treatment dose, the results and methodology could be extended for any polymer of industrial scale, such as those used in medical implants, defense armor, bulletproof jackets, etc.


  • The cost analysis of a leading optics business in Saudi Arabia

    by Ahmed A. Bakhsh

    This study aims to use discrete event simulation (DES) to minimise the processing cost of a leading optics business in Saudi Arabia. Data is collected from three branches to calculate the operating cost and delivery time of the products. A proposed solution is developed to replace three technical workshops inside every branch with one central workshop in the city. Numbers of replications are carried out to reach the optimal solution. Cost analysis is done to compare the process cost, delivery time and idle working hours of the two options. A significant reduction is observed in the process cost and delivery time of the products besides increasing the idle working hours of the technicians. These improvements can be utilised to enhance the productivity and profitability of the organisations.

  • Open Access

    Traffic Simulation Modeling for Major Intersection

    by Ahmed Bakhsh

    The computer simulation is a widespread in industry to support decisions and to approximate systems performance that is not easy to be analyzed. The real decisions often encounter optimization of multiple and opposing, objectives. It is common for transportation problems to be addressed by simulation modeling that use traditional analytical ways. Different kinds of models are investigated depend on the studied problem. This paper examines traffic control mean in terms of the performance measures when utilized in an urban area intersection, i.e. which design minimizes total time in system and waiting time while maximizing number of vehicles out. Simulation models for the base and alternatives are considered in comparison for the best results.


  • BIOGAS TECHNOLOGIES FOR SUSTAINABLE IMPROVEMENT OF ENERGY DIVERSITY

    by Mohammed Balubaid, Rami Al Amoudi, Ahmed A. Bakhsh, Osman Taylan, Basil Al Sasi, Fatma Çanka Kiliç, Durmus Kaya

  • Open Access

    A Financial Simulation Modeling for Major University in the Middle East

    by Ahmed Atef Bakhsh

    In the present economic environment, it is critical for organizations to precisely monitor and forecast financial issues for better decision-making. This study constructed a model for the college of Engineering's financial operation of a major University in the Middle East by looking at the numbers of its revenues and expenses. Moreover, object-oriented simulation (OOS) tools is used for the financial model that support the subject matter experts in how the model can be used to help them make decisions regarding topics such as: does it make sense to introduce a new major now or in the future, should the college try to enroll more students, or even should a specific course be offered at a specific semester. The simulation model help in financial terms only.