Christopher R. McGann
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Christopher R. McGann has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
Pedro Arduino
Department of Civil and Environmental Engineering, University of Washington, 201 More Hall, Box 352700, Seattle, WA 98195
6 shared publicationsBrendon A. Bradley
Department of Civil and Natural Resources Engineering University of Canterbury Christchurch New Zealand
4 shared publications- Brendon A. Bradley
Department of Civil and Environmental Engineering University of Canterbury Christchurch New Zealand
4 shared publications Liam M. Wotherspoon
Univ Auckland, Auckland, New Zealand
4 shared publicationsPeter Mackenzie-Helnwein
4 shared publicationsMisko Cubrinovski
3 shared publications
Latest Publications
- 2 September 2026
- Published by Springer Nature
- p. 26-34
Effective Stress Analysis of Lateral Spreading at the Mataquito River Bridge
- 2 September 2026
- Published by Springer Nature
- p. 26-34
Effective Stress Analysis of Lateral Spreading at the Mataquito River Bridge
- Open Access
- 1 December 2025
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 30 (12)
Large-Scale Pseudotsunami Testing of Novel Bridge Deck-to-Pier Connections
- 1 December 2025
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 30 (12)
Open AccessLarge-Scale Pseudotsunami Testing of Novel Bridge Deck-to-Pier Connections
- 9 November 2025
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- p. 1-16
Testing and optimisation of resilient deck-to-pier connections for tsunami-prone coastal bridges
- 9 November 2025
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- p. 1-16
Testing and optimisation of resilient deck-to-pier connections for tsunami-prone coastal bridges
- Open Access
- 16 October 2025
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 200
2D site response modeling of the Treasure Island vertical array considering spatially varying input motions with non-vertical incidence
- 16 October 2025
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 200
Open Access2D site response modeling of the Treasure Island vertical array considering spatially varying input motions with non-vertical incidence
- Open Access
- 1 April 2024
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 180
Stress-density model validation: Free-field liquefaction analysis
- 1 April 2024
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 180
Open AccessStress-density model validation: Free-field liquefaction analysis
- Open Access
- 1 September 2023
- Published by New Zealand Society for Earthquake Engineering in Bulletin of the New Zealand Society for Earthquake Engineering
- Vol. 56 (3) , 169-185
The state of practice in soil-structure interaction modelling in New Zealand
The current state of practice in soil-structure interaction (SSI) modelling in New Zealand was investigated through an industry-wide questionnaire. This used a mixed methods, sequential explanatory research design involving the collection of quantitative and qualitative questionnaire data, as well as follow-up focus groups. Several statistically significant relationships were observed for SSI modelling approaches between different engineering fields, company sizes, and years of experience. The key findings from this study suggest that there is no consensus on the best SSI analysis methods, modelling strategies, or guidelines to be used. Overall, fixed base analysis remains the most popular method across all company sizes and number of years of industry experience. Engineers from large companies reported higher consideration for SSI modelling and use of performance-based design for design projects, which perhaps reflects the scale and complexity of projects carried out in those companies. However when SSI is considered, analyses are typically limited to nonlinear vertical springs under the foundation as part of a dynamic analysis. Use of SSI for buildings is typically limited to seismic assessments and complex or otherwise high importance structures. However, bridge engineers routinely used pushover analyses with linear and nonlinear springs and dynamic analyses with nonlinear springs, in contrast with the rest of the industry. There is further room to improve on the quality of communication and interaction between structural and geotechnical engineers. A lack of specific guidance on when SSI should be considered was reported, alongside broader training issues to ensure that structural and geotechnical engineers fundamentally understand the requirements and input/output needs of each role.
- 1 September 2023
- Published by New Zealand Society for Earthquake Engineering in Bulletin of the New Zealand Society for Earthquake Engineering
- Vol. 56 (3) , 169-185
Open AccessThe state of practice in soil-structure interaction modelling in New Zealand
The current state of practice in soil-structure interaction (SSI) modelling in New Zealand was investigated through an industry-wide questionnaire. This used a mixed methods, sequential explanatory research design involving the collection of quantitative and qualitative questionnaire data, as well as follow-up focus groups. Several statistically significant relationships were observed for SSI modelling approaches between different engineering fields, company sizes, and years of experience. The key findings from this study suggest that there is no consensus on the best SSI analysis methods, modelling strategies, or guidelines to be used. Overall, fixed base analysis remains the most popular method across all company sizes and number of years of industry experience. Engineers from large companies reported higher consideration for SSI modelling and use of performance-based design for design projects, which perhaps reflects the scale and complexity of projects carried out in those companies. However when SSI is considered, analyses are typically limited to nonlinear vertical springs under the foundation as part of a dynamic analysis. Use of SSI for buildings is typically limited to seismic assessments and complex or otherwise high importance structures. However, bridge engineers routinely used pushover analyses with linear and nonlinear springs and dynamic analyses with nonlinear springs, in contrast with the rest of the industry. There is further room to improve on the quality of communication and interaction between structural and geotechnical engineers. A lack of specific guidance on when SSI should be considered was reported, alongside broader training issues to ensure that structural and geotechnical engineers fundamentally understand the requirements and input/output needs of each role.
- 1 November 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 147 (11) , 04021131
Assessment of Existing SPT–CPT Correlations Using a New Zealand Database
Using a database of approximately 900 data pairs from 230 sites of co-located cone penetration test (CPT) soundings and boreholes with standard penetration tests (SPT) in the South Island of New Zealand, this paper assesses the applicability of a range of existing SPT–CPT correlations. Simple linear SPT–CPT correlations for different soil types as well as correlations based on the soil behavior type index ( ) from CPT data were assessed. The measured SPT data were poorly fit by all the correlations, with under- and over-predictions greater than 50% for between 40% and 55% of the database. The 95% confidence interval of the bias between predicted and measured SPT values was large across all variables. The bias varied significantly as a function of CPT tip resistance and sleeve friction, with underestimates at low values dominated by fine-grained soils ( ), and overestimates at high values dominated by silty sand to dense sand ( ). There was no clear effect of the different drilling methods on the bias observed across all parameters. These results highlight the significant uncertainty involved in the application of these correlations in geotechnical design and assessments.- 1 November 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 147 (11) , 04021131
Assessment of Existing SPT–CPT Correlations Using a New Zealand Database
Using a database of approximately 900 data pairs from 230 sites of co-located cone penetration test (CPT) soundings and boreholes with standard penetration tests (SPT) in the South Island of New Zealand, this paper assesses the applicability of a range of existing SPT–CPT correlations. Simple linear SPT–CPT correlations for different soil types as well as correlations based on the soil behavior type index ( ) from CPT data were assessed. The measured SPT data were poorly fit by all the correlations, with under- and over-predictions greater than 50% for between 40% and 55% of the database. The 95% confidence interval of the bias between predicted and measured SPT values was large across all variables. The bias varied significantly as a function of CPT tip resistance and sleeve friction, with underestimates at low values dominated by fine-grained soils ( ), and overestimates at high values dominated by silty sand to dense sand ( ). There was no clear effect of the different drilling methods on the bias observed across all parameters. These results highlight the significant uncertainty involved in the application of these correlations in geotechnical design and assessments.- 1 July 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 146 (7) , 04020055
Parametric Assessment of Equivalent Static Procedure Accounting for Foundation-Pinning Effects in Analysis of Piled Bridge Abutments Subject to Lateral Spreading
Foundation pinning is a critical consideration for design and analysis of bridge foundations subject to liquefaction-induced lateral spreading, particularly for bridges with a standard approach embankment of finite width. The simplified analysis procedure that has been generally adopted for this case makes consideration for foundation-pinning effects by considering the compatibility between the near-field soil and foundation displacements; however, there is a lack of guidance or evidence indicating the practical limitations of the simplified method. This paper discusses the results of a large parametric study carried out using three-dimensional (3D) finite-element models and simplified analysis models of corresponding site conditions. This study is designed to identify the range of conditions where the simplified method produces reasonable results and to determine the expected reduction in near-field displacements relative to those in the free field for different site geometries such that future applications of the simplified pile-pinning analysis procedure will have a benchmark for comparison.
- 1 July 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 146 (7) , 04020055
Parametric Assessment of Equivalent Static Procedure Accounting for Foundation-Pinning Effects in Analysis of Piled Bridge Abutments Subject to Lateral Spreading
Foundation pinning is a critical consideration for design and analysis of bridge foundations subject to liquefaction-induced lateral spreading, particularly for bridges with a standard approach embankment of finite width. The simplified analysis procedure that has been generally adopted for this case makes consideration for foundation-pinning effects by considering the compatibility between the near-field soil and foundation displacements; however, there is a lack of guidance or evidence indicating the practical limitations of the simplified method. This paper discusses the results of a large parametric study carried out using three-dimensional (3D) finite-element models and simplified analysis models of corresponding site conditions. This study is designed to identify the range of conditions where the simplified method produces reasonable results and to determine the expected reduction in near-field displacements relative to those in the free field for different site geometries such that future applications of the simplified pile-pinning analysis procedure will have a benchmark for comparison.
- 1 September 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 144 (9)
Empirical Correlation for Estimating Shear-Wave Velocity from Cone Penetration Test Data for Banks Peninsula Loess Soils in Canterbury, New Zealand
Seismic piezocone data obtained from Banks Peninsula loess soil sites in the Port Hills south of Christchurch, New Zealand, are used with multiple linear regression to develop a new Banks Peninsula loess-specific correlation for predicting shear wave velocity ( ) from cone penetration test (CPT) measurements. The need for this new correlation is demonstrated through comparisons with existing models, including a recently developed Christchurch-specific general soils model, with the loess measurements. It is shown that the existing general soil models tend to systematically underpredict the loess , and it is demonstrated that this underprediction is due to fundamental differences in how the properties of loess and general soil types affect both CPT measurements and shear-wave velocity, and that aging effects alone cannot account for the observed differences.- 1 September 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 144 (9)
Empirical Correlation for Estimating Shear-Wave Velocity from Cone Penetration Test Data for Banks Peninsula Loess Soils in Canterbury, New Zealand
Seismic piezocone data obtained from Banks Peninsula loess soil sites in the Port Hills south of Christchurch, New Zealand, are used with multiple linear regression to develop a new Banks Peninsula loess-specific correlation for predicting shear wave velocity ( ) from cone penetration test (CPT) measurements. The need for this new correlation is demonstrated through comparisons with existing models, including a recently developed Christchurch-specific general soils model, with the loess measurements. It is shown that the existing general soil models tend to systematically underpredict the loess , and it is demonstrated that this underprediction is due to fundamental differences in how the properties of loess and general soil types affect both CPT measurements and shear-wave velocity, and that aging effects alone cannot account for the observed differences.- 7 June 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 10-18
Bridge Foundation Pinning Resistance Implied by Equivalent Static Analysis Procedure for Liquefaction-Induced Lateral Spreading
Liquefaction-induced lateral soil deformation is an important design consideration for bridges in high-seismicity regions. The equivalent static analysis (ESA) procedure that has been widely adopted for this load case considers the compatibility between the soil and foundation deformation in the near-field, i.e. foundation pinning effects. However, there is not much direct guidance on the significance of the foundation pinning in the ESA relative to the free-field lateral deformations. The purpose of this study is to use a large parameter study to assess how changes in approach embankment width, soil profile, and foundation stiffness affect the compatible displacement returned by the ESA, and to characterize the foundation pinning implied by these compatible displacements through comparison to estimated free-field deformations. It is shown that the compatible displacements returned by the ESA are less than half of the free-field deformation for all cases, and that this reduction is driven primarily by the slope stability phase of the ESA.
- 7 June 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 10-18
Bridge Foundation Pinning Resistance Implied by Equivalent Static Analysis Procedure for Liquefaction-Induced Lateral Spreading
Liquefaction-induced lateral soil deformation is an important design consideration for bridges in high-seismicity regions. The equivalent static analysis (ESA) procedure that has been widely adopted for this load case considers the compatibility between the soil and foundation deformation in the near-field, i.e. foundation pinning effects. However, there is not much direct guidance on the significance of the foundation pinning in the ESA relative to the free-field lateral deformations. The purpose of this study is to use a large parameter study to assess how changes in approach embankment width, soil profile, and foundation stiffness affect the compatible displacement returned by the ESA, and to characterize the foundation pinning implied by these compatible displacements through comparison to estimated free-field deformations. It is shown that the compatible displacements returned by the ESA are less than half of the free-field deformation for all cases, and that this reduction is driven primarily by the slope stability phase of the ESA.