Albert D. Smith
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Albert D. Smith has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
- Jack Donoghue
University of Manchester
5 shared publications M. Preuss
Department of Materials, The Henry Royce Institute, The University of Manchester, Manchester M13 9PL, UK; Department of Materials Science and Engineering, Monash University, Clayton, VIC 3800, Australia
3 shared publicationsAllan Harte
2 shared publications- David Lunt
Department of Materials, University of Manchester, Manchester, UK
2 shared publications K. Wilford
Rolls Royce Plc, London, England
2 shared publicationsA. Candeias
NewTec Scientific, 2 route de Sommières, Caveirac 30820, France
1 shared publication
Latest Publications
- Open Access
- 23 September 2025
- Published by Elsevier in Ultramicroscopy
- Vol. 280, 114244
A new approach to SEM in-situ thermomechanical experiments through automation
- 23 September 2025
- Published by Elsevier in Ultramicroscopy
- Vol. 280, 114244
Open AccessA new approach to SEM in-situ thermomechanical experiments through automation
- Open Access
- 12 August 2025
- Published by Elsevier in Materials & Design
- Vol. 258
Development and characterisation of a liquid phase assisted healable aluminium-magnesium alloy processed by Laser Powder Bed Fusion
- 12 August 2025
- Published by Elsevier in Materials & Design
- Vol. 258
Open AccessDevelopment and characterisation of a liquid phase assisted healable aluminium-magnesium alloy processed by Laser Powder Bed Fusion
- Open Access
- 1 November 2024
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 604
Microstructure and mechanical performance of cold spray Cr coatings
- 1 November 2024
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 604
Open AccessMicrostructure and mechanical performance of cold spray Cr coatings
- Open Access
- 6 December 2023
- Published by Elsevier in Scripta Materialia
- Vol. 242
In-situ heating-stage EBSD validation of algorithms for prior-austenite grain reconstruction in steel
- 6 December 2023
- Published by Elsevier in Scripta Materialia
- Vol. 242
Open AccessIn-situ heating-stage EBSD validation of algorithms for prior-austenite grain reconstruction in steel
- Open Access
- 31 March 2023
- Published by Elsevier in Acta Materialia
- Vol. 250
Mapping plastic deformation mechanisms in AZ31 magnesium alloy at the nanoscale
- 31 March 2023
- Published by Elsevier in Acta Materialia
- Vol. 250
Open AccessMapping plastic deformation mechanisms in AZ31 magnesium alloy at the nanoscale
- Open Access
- 1 August 2020
- Published by Elsevier in Acta Materialia
- Vol. 194, 257-275
The effect of solid solution and gamma prime on the deformation modes in Ni-based superalloys
- 1 August 2020
- Published by Elsevier in Acta Materialia
- Vol. 194, 257-275
Open AccessThe effect of solid solution and gamma prime on the deformation modes in Ni-based superalloys
- 1 August 2020
- Published by Elsevier in Materials Letters
- Vol. 273
Strain based electrical resistance behaviour of graphene-coated elastomeric yarns
- 1 August 2020
- Published by Elsevier in Materials Letters
- Vol. 273
Strain based electrical resistance behaviour of graphene-coated elastomeric yarns
- Open Access
- 24 March 2020
- Published by Springer Nature in Scientific Reports
- Vol. 10 (1) , 1-11
Novel Methods for Recording Stress-Strain Curves in Proton Irradiated Material
Proton irradiation is often used as a proxy for neutron irradiation but the irradiated layer is typically in-situ loading experiments are carried out using a combination of X-ray diffraction and digital image correlation on the near surface region in order to measure stress and strain, thereby eliminating the influence of the non-irradiated volume. The second approach is to manufacture small-scale tensile specimens containing only the proton irradiated volume but approaching the smallest representative volume of the material. This is achieved by high-speed focused ion beam (FIB) milling though the application of a Xe+ Plasma-FIB (PFIB). It is demonstrated that both techniques are capable of recording the early stage of uniaxial flow behaviour of the irradiated material with sufficient accuracy providing a measure of irradiation-induced shift of yield strength, strain hardening and tensile strength.
- 24 March 2020
- Published by Springer Nature in Scientific Reports
- Vol. 10 (1) , 1-11
Open AccessNovel Methods for Recording Stress-Strain Curves in Proton Irradiated Material
Proton irradiation is often used as a proxy for neutron irradiation but the irradiated layer is typically in-situ loading experiments are carried out using a combination of X-ray diffraction and digital image correlation on the near surface region in order to measure stress and strain, thereby eliminating the influence of the non-irradiated volume. The second approach is to manufacture small-scale tensile specimens containing only the proton irradiated volume but approaching the smallest representative volume of the material. This is achieved by high-speed focused ion beam (FIB) milling though the application of a Xe+ Plasma-FIB (PFIB). It is demonstrated that both techniques are capable of recording the early stage of uniaxial flow behaviour of the irradiated material with sufficient accuracy providing a measure of irradiation-induced shift of yield strength, strain hardening and tensile strength.
- 24 July 2019
- Published by Springer Nature in Experimental Mechanics
- Vol. 59 (8) , 1113-1125
On the Application of Xe+ Plasma FIB for Micro-fabrication of Small-scale Tensile Specimens
- 24 July 2019
- Published by Springer Nature in Experimental Mechanics
- Vol. 59 (8) , 1113-1125
On the Application of Xe+ Plasma FIB for Micro-fabrication of Small-scale Tensile Specimens