George A. Hazelrigg
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
George A. Hazelrigg has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Donald G. Saari
University of California, Irvine, USA
2 shared publications - Georgia-Ann Klutke
Division of Civil, Mechanical and Manufacturing Innovation, National Science Foundation, 2415 Eisenhower Avenue, Alexandria, VA 22314
2 shared publications - Joshua Roland Campbell
George Mason University Department of Mechanical Engineering Fairfax, VA 22030
1 shared publication
Latest Publications
- 29 March 2023
- Published by Wiley in Journal of Mechanical Design
- Vol. 145 (6) , 1-11
Tolerancing for an Apple Pie: A Fundamental Theory of Tolerances
Tolerancing began with the notion of limits imposed on the dimensions of realized parts both to maintain functional geometric dimensionality and to enable cost-effective part fabrication and inspection. Increasingly, however, component fabrication depends on more than part geometry as many parts are fabricated as a result of a “recipe” rather than dimensional instructions for material addition or removal. Referred to as process tolerancing, this is the case, for example, with IC chips. In the case of tolerance optimization, a typical objective is cost minimization while achieving required functionality or “quality.” This article takes a different look at tolerances, suggesting that rather than ensuring merely that parts achieve a desired functionality at minimum cost, a typical underlying goal of the product design is to make money, more is better, and tolerances comprise additional design variables amenable to optimization in a decision theoretic framework. We further recognize that tolerances introduce additional product attributes that relate to product characteristics such as consistency, quality, reliability, and durability. These important attributes complicate the computation of the expected utility of candidate designs, requiring additional computational steps for their determination. The resulting theory of tolerancing illuminates the assumptions and limitations inherent to Taguchi’s loss function. We illustrate the theory using the example of tolerancing for an apple pie, which conveniently demands consideration of tolerances on both quantities and processes, and the interaction among these tolerances.
- 29 March 2023
- Published by Wiley in Journal of Mechanical Design
- Vol. 145 (6) , 1-11
Tolerancing for an Apple Pie: A Fundamental Theory of Tolerances
Tolerancing began with the notion of limits imposed on the dimensions of realized parts both to maintain functional geometric dimensionality and to enable cost-effective part fabrication and inspection. Increasingly, however, component fabrication depends on more than part geometry as many parts are fabricated as a result of a “recipe” rather than dimensional instructions for material addition or removal. Referred to as process tolerancing, this is the case, for example, with IC chips. In the case of tolerance optimization, a typical objective is cost minimization while achieving required functionality or “quality.” This article takes a different look at tolerances, suggesting that rather than ensuring merely that parts achieve a desired functionality at minimum cost, a typical underlying goal of the product design is to make money, more is better, and tolerances comprise additional design variables amenable to optimization in a decision theoretic framework. We further recognize that tolerances introduce additional product attributes that relate to product characteristics such as consistency, quality, reliability, and durability. These important attributes complicate the computation of the expected utility of candidate designs, requiring additional computational steps for their determination. The resulting theory of tolerancing illuminates the assumptions and limitations inherent to Taguchi’s loss function. We illustrate the theory using the example of tolerancing for an apple pie, which conveniently demands consideration of tolerances on both quantities and processes, and the interaction among these tolerances.
- 22 July 2021
- Published by ASME International in Journal of Verification, Validation and Uncertainty Quantification
- Vol. 6 (3)
Response to “Closure on the Discussion of “Models, Uncertainty, and the Sandia V&V Challenge Problem” ” (Oberkampf, W. L., and Balch, M. S., ASME J. Verif. Valid. Uncert., 2020, 5(3), p. 035501-1)
This is a very short response. An abstract would be inappropriate.
- 22 July 2021
- Published by ASME International in Journal of Verification, Validation and Uncertainty Quantification
- Vol. 6 (3)
Response to “Closure on the Discussion of “Models, Uncertainty, and the Sandia V&V Challenge Problem” ” (Oberkampf, W. L., and Balch, M. S., ASME J. Verif. Valid. Uncert., 2020, 5(3), p. 035501-1)
This is a very short response. An abstract would be inappropriate.
- Open Access
- 16 July 2021
- Published by ASME International
Toward a Theory of Systems Engineering
The derivation of a theory of systems engineering has long been complicated by the fact that there is little consensus within the systems engineering community regarding precisely what systems engineering is, what systems engineers do, and what might con- stitute reasonable systems engineering practices. To date, attempts at theories fail to accommodate even a sizable
- 16 July 2021
- Published by ASME International
Open AccessToward a Theory of Systems Engineering
The derivation of a theory of systems engineering has long been complicated by the fact that there is little consensus within the systems engineering community regarding precisely what systems engineering is, what systems engineers do, and what might con- stitute reasonable systems engineering practices. To date, attempts at theories fail to accommodate even a sizable
- 1 March 2020
- Published by ASME International in Journal of Verification, Validation and Uncertainty Quantification
- Vol. 5 (1)
Models, Uncertainty, and the Sandia V&V Challenge Problem
The purpose of this paper is not to present new results; rather, it is to show that the current approach to model validation is not consistent with the accepted mathematics of probability theory. Specifically, we argue that the Sandia V&V Challenge Problem is ill-posed in that the answers sought do not, mathematically, exist. We apply our arguments to show the types of mistakes present in the papers presented in the Journal of Verification, Validation and Uncertainty Quantification, Volume 1,1 along with the challenge problem. Further, we argue that, when the problem is properly posed, both the applicable methodology and the solution techniques are easily drawn from the well-developed mathematics of probability and decision theory. The unfortunate aspect of the challenge problem as currently stated is that it leads to incorrect and inappropriate mathematical approaches that should be avoided and corrected in the current literature.
- 1 March 2020
- Published by ASME International in Journal of Verification, Validation and Uncertainty Quantification
- Vol. 5 (1)
Models, Uncertainty, and the Sandia V&V Challenge Problem
The purpose of this paper is not to present new results; rather, it is to show that the current approach to model validation is not consistent with the accepted mathematics of probability theory. Specifically, we argue that the Sandia V&V Challenge Problem is ill-posed in that the answers sought do not, mathematically, exist. We apply our arguments to show the types of mistakes present in the papers presented in the Journal of Verification, Validation and Uncertainty Quantification, Volume 1,1 along with the challenge problem. Further, we argue that, when the problem is properly posed, both the applicable methodology and the solution techniques are easily drawn from the well-developed mathematics of probability and decision theory. The unfortunate aspect of the challenge problem as currently stated is that it leads to incorrect and inappropriate mathematical approaches that should be avoided and corrected in the current literature.
- 5 September 2019
- Published by Wiley in Journal of Mechanical Design
- Vol. 141 (10) , 1-4
A Note on the Weighted Sum Method
- 5 September 2019
- Published by Wiley in Journal of Mechanical Design
- Vol. 141 (10) , 1-4
A Note on the Weighted Sum Method