Sangjun Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sangjun Lee has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Sungho Kang
Yonsei University
6 shared publications - Jongho Park
Department of Electrical and Electronic Engineering, Yonsei University, Seoul, South Korea
3 shared publications - Jihye Kim
Department of Electrical and Electronic Engineering, Yonsei University, Seoul, South Korea
2 shared publications Sungwhan Park
Department of Electrical and Electronic Engineering, Yonsei University, Seoul, South Korea
2 shared publicationsDonghyun Bae
Department of Materials Science and Engineering Yonsei University Seoul 03722 Korea
1 shared publicationGijoon Bae
Department of Materials Science and Engineering Yonsei University Seoul 03722 Korea
1 shared publication
Latest Publications
- 20 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (5) , 2649-2653
A New Zero-Overhead Test Method for Low-Power AI Accelerators
Artificial intelligence (AI) accelerators that support AI services consist of multiple identical cores for parallel computation to accelerate artificial neural networks. Recently, systolic array-based architectures for low-power AI accelerators have been studied to support battery-operated edge devices and reduce power consumption. In this paper, a zero-overhead method is proposed for efficient testing of systolic array-based low-power AI accelerators. By using the structural characteristics of the systolic array and a reset operation, the proposed method can test multiple identical cores based on the systolic array without any additional hardware. The proposed method is divided into MAC and comparator test methods to use the structural characteristics of systolic arrays for low-power AI accelerators. The experimental results demonstrate that the proposed method achieves 100% test coverage without any additional hardware and has reasonable test times compared to previous methods.
- 20 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (5) , 2649-2653
A New Zero-Overhead Test Method for Low-Power AI Accelerators
Artificial intelligence (AI) accelerators that support AI services consist of multiple identical cores for parallel computation to accelerate artificial neural networks. Recently, systolic array-based architectures for low-power AI accelerators have been studied to support battery-operated edge devices and reduce power consumption. In this paper, a zero-overhead method is proposed for efficient testing of systolic array-based low-power AI accelerators. By using the structural characteristics of the systolic array and a reset operation, the proposed method can test multiple identical cores based on the systolic array without any additional hardware. The proposed method is divided into MAC and comparator test methods to use the structural characteristics of systolic arrays for low-power AI accelerators. The experimental results demonstrate that the proposed method achieves 100% test coverage without any additional hardware and has reasonable test times compared to previous methods.
- 25 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 343-344
A New Flip-flop Shared Architecture of Test Point Insertion for Scan Design
Since the demand for chips with high reliability is increasing, built-in self-tests (BISTs) are widely used in these days. Test point insertion (TPI) is an efficient and intuitive method to enhance the test coverage; however, due to the extra logics, increasing area overhead is inevitable. Furthermore, as growing chip size, reducing wire overhead becomes a significant problem. In this paper, a new method of TPI involving a new architecture of flip-flop (FF) shared TPI and a optimizing the test points (TPs) with considering place to reduce the area overhead. Not only hardware overhead is reduced by the new architecture, but also wire overhead is reduced by optimizing. The experimental results show reduced area overhead without significant degradation of test coverage.
- 25 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 343-344
A New Flip-flop Shared Architecture of Test Point Insertion for Scan Design
Since the demand for chips with high reliability is increasing, built-in self-tests (BISTs) are widely used in these days. Test point insertion (TPI) is an efficient and intuitive method to enhance the test coverage; however, due to the extra logics, increasing area overhead is inevitable. Furthermore, as growing chip size, reducing wire overhead becomes a significant problem. In this paper, a new method of TPI involving a new architecture of flip-flop (FF) shared TPI and a optimizing the test points (TPs) with considering place to reduce the area overhead. Not only hardware overhead is reduced by the new architecture, but also wire overhead is reduced by optimizing. The experimental results show reduced area overhead without significant degradation of test coverage.
- Open Access
- 5 October 2021
- Published by Wiley in Advanced Materials Technologies
- Vol. 6 (10) , 2170061
Colorimetric Detection of Mechanical Deformation in Metals using Thin‐Film Mechanochromic Sensor (Adv. Mater. Technol. 10/2021)
- 5 October 2021
- Published by Wiley in Advanced Materials Technologies
- Vol. 6 (10) , 2170061
Open AccessColorimetric Detection of Mechanical Deformation in Metals using Thin‐Film Mechanochromic Sensor (Adv. Mater. Technol. 10/2021)
- Open Access
Low-Power Scan Correlation-Aware Scan Cluster Reordering for Wireless Sensor Networks
Cryptographic circuits generally are used for applications of wireless sensor networks to ensure security and must be tested in a manufacturing process to guarantee their quality. Therefore, a scan architecture is widely used for testing the circuits in the manufacturing test to improve testability. However, during scan testing, test-power consumption becomes more serious as the number of transistors and the complexity of chips increase. Hence, the scan chain reordering method is widely applied in a low-power architecture because of its ability to achieve high power reduction with a simple architecture. However, achieving a significant power reduction without excessive computational time remains challenging. In this paper, a novel scan correlation-aware scan cluster reordering is proposed to solve this problem. The proposed method uses a new scan correlation-aware clustering in order to place highly correlated scan cells adjacent to each other. The experimental results demonstrate that the proposed method achieves a significant power reduction with a relatively fast computational time compared with previous methods. Therefore, by improving the reliability of cryptography circuits in wireless sensor networks (WSNs) through significant test-power reduction, the proposed method can ensure the security and integrity of information in WSNs.
Open AccessLow-Power Scan Correlation-Aware Scan Cluster Reordering for Wireless Sensor Networks
Cryptographic circuits generally are used for applications of wireless sensor networks to ensure security and must be tested in a manufacturing process to guarantee their quality. Therefore, a scan architecture is widely used for testing the circuits in the manufacturing test to improve testability. However, during scan testing, test-power consumption becomes more serious as the number of transistors and the complexity of chips increase. Hence, the scan chain reordering method is widely applied in a low-power architecture because of its ability to achieve high power reduction with a simple architecture. However, achieving a significant power reduction without excessive computational time remains challenging. In this paper, a novel scan correlation-aware scan cluster reordering is proposed to solve this problem. The proposed method uses a new scan correlation-aware clustering in order to place highly correlated scan cells adjacent to each other. The experimental results demonstrate that the proposed method achieves a significant power reduction with a relatively fast computational time compared with previous methods. Therefore, by improving the reliability of cryptography circuits in wireless sensor networks (WSNs) through significant test-power reduction, the proposed method can ensure the security and integrity of information in WSNs.
- Open Access
- 17 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 116115-116132
A Low-Power BIST Scheme Using Weight-Aware Scan Grouping and Scheduling for Automotive ICs
Scan-based logic built-in self-test (LBIST) is widely used for supporting the in-system test in automotive systems. Although this technology has the advantage of low-cost testing, it suffers from low fault coverage and high switching activity during the test. This can lead to many undetected defects, excessive heat dissipation, and IR drop, inducing catastrophic risks to functional safety. Therefore, improving these two key factors is crucial to alleviate reliability problems in the automotive domain. Most previous works have focused on controlling the enormous toggling level of random patterns; however, one of the main disadvantages of these approaches is low fault coverage. Unfortunately, additional hardware costs associated with memory elements or test points are required for detecting the remaining faults. We propose a novel LBIST scheme based on weight-aware scan grouping and scheduling (WGS) to overcome these difficulties. Since the required test time of each automotive product is limited, the proposed scheme freezes the test time and focuses on improving both aforementioned factors significantly. Our approach divides scan cells into two categories: the coverage-efficient scan group and power-efficient scan group, and then it conducts weight-based scan cell reordering. Biased random patterns are fed to enhance fault coverage for the first category. For the second category, scheduling and disabling are performed to reduce switching activity. Finally, physical-aware reordering based on an inverter is performed to reduce routing overhead. Experimental results demonstrate the feasibility of the WGS methodology on the ITC’99 and OpenRISC benchmark circuits.
- 17 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 116115-116132
Open AccessA Low-Power BIST Scheme Using Weight-Aware Scan Grouping and Scheduling for Automotive ICs
Scan-based logic built-in self-test (LBIST) is widely used for supporting the in-system test in automotive systems. Although this technology has the advantage of low-cost testing, it suffers from low fault coverage and high switching activity during the test. This can lead to many undetected defects, excessive heat dissipation, and IR drop, inducing catastrophic risks to functional safety. Therefore, improving these two key factors is crucial to alleviate reliability problems in the automotive domain. Most previous works have focused on controlling the enormous toggling level of random patterns; however, one of the main disadvantages of these approaches is low fault coverage. Unfortunately, additional hardware costs associated with memory elements or test points are required for detecting the remaining faults. We propose a novel LBIST scheme based on weight-aware scan grouping and scheduling (WGS) to overcome these difficulties. Since the required test time of each automotive product is limited, the proposed scheme freezes the test time and focuses on improving both aforementioned factors significantly. Our approach divides scan cells into two categories: the coverage-efficient scan group and power-efficient scan group, and then it conducts weight-based scan cell reordering. Biased random patterns are fed to enhance fault coverage for the first category. For the second category, scheduling and disabling are performed to reduce switching activity. Finally, physical-aware reordering based on an inverter is performed to reduce routing overhead. Experimental results demonstrate the feasibility of the WGS methodology on the ITC’99 and OpenRISC benchmark circuits.
- 23 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 67 (12) , 3432-3436
A New Logic Topology-Based Scan Chain Stitching for Test-Power Reduction
A scan architecture is the most widely used for obtaining high test coverage in manufacturing tests. However, the recent increase in circuit size has caused the power consumption during scan testing to become higher than that in the functional mode. Thus, the reliability of scan testing has become a concern. In this brief, a new logic topology-based scan chain stitching method is proposed to reduce the test power. The proposed method uses the topology of logic circuits to analyze them without relying on specific test patterns. The proposed method is beneficial for reduction of both computation time and test power during testing with various test patterns. The method performs two processes to consider the shift-in and shift-out powers. The first process, logic topology-based scan partitioning, forms scan chains based on scan estimation value that estimates the shift-out data occurring in flip-flops. The second process, logic topology-based scan stitching, determines the order of the flip-flops by calculating the scan influence value, using which the proposed method can reduce the shift-in power by consolidating the care bit density in the test patterns. The experiments conducted on ISCAS’89 and ITC’99 benchmark circuits demonstrate that on average, the proposed method reduces the shift power by 28.36% compared with a previous logic topology-based scan chain stitching method.
- 23 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 67 (12) , 3432-3436
A New Logic Topology-Based Scan Chain Stitching for Test-Power Reduction
A scan architecture is the most widely used for obtaining high test coverage in manufacturing tests. However, the recent increase in circuit size has caused the power consumption during scan testing to become higher than that in the functional mode. Thus, the reliability of scan testing has become a concern. In this brief, a new logic topology-based scan chain stitching method is proposed to reduce the test power. The proposed method uses the topology of logic circuits to analyze them without relying on specific test patterns. The proposed method is beneficial for reduction of both computation time and test power during testing with various test patterns. The method performs two processes to consider the shift-in and shift-out powers. The first process, logic topology-based scan partitioning, forms scan chains based on scan estimation value that estimates the shift-out data occurring in flip-flops. The second process, logic topology-based scan stitching, determines the order of the flip-flops by calculating the scan influence value, using which the proposed method can reduce the shift-in power by consolidating the care bit density in the test patterns. The experiments conducted on ISCAS’89 and ITC’99 benchmark circuits demonstrate that on average, the proposed method reduces the shift power by 28.36% compared with a previous logic topology-based scan chain stitching method.
- 3 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 27 (8) , 1972-1976
Test-Friendly Data-Selectable Self-Gating (DSSG)
Low-power design is a key consideration in modern design. xor self-gating (data-driven self-gating) is used for power reduction in clock networks, which is one of the main factors of dynamic power consumption. When applying xor self-gating, dynamic power consumption is reduced, but the number of required test patterns on the testing side is inflated. In critical cases, more than three times the regular number of scan test patterns may be required for industrial designs, such as GPUs. In this brief, we propose a novel self-gating structure. Data- selectable self-gating (DSSG) is designed to use functional data and scan data selectively to eliminate the unnecessary clock toggling of flip-flops. With this structure, the self-gating function can be used in the scan test mode, as well as the function mode. When the self-gating logic is used during scan shift operations, the stuck-at faults in the self-gating logic can be tested with short test sequences; therefore, the rise in test costs can be mitigated. It is possible to test the stuck-at faults in self-gating logic using only four scan test patterns. The experimental results show that the average of the stuck-at test pattern increase ratio has been dropped from more than 90% to less than 8%. The low-power performance of the proposed method in the mission mode is the same as that of the conventional self-gating structures. When the DSSG method is used, the dynamic power of the shift operation which may increase excessively during the scan test can be reduced.
- 3 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 27 (8) , 1972-1976
Test-Friendly Data-Selectable Self-Gating (DSSG)
Low-power design is a key consideration in modern design. xor self-gating (data-driven self-gating) is used for power reduction in clock networks, which is one of the main factors of dynamic power consumption. When applying xor self-gating, dynamic power consumption is reduced, but the number of required test patterns on the testing side is inflated. In critical cases, more than three times the regular number of scan test patterns may be required for industrial designs, such as GPUs. In this brief, we propose a novel self-gating structure. Data- selectable self-gating (DSSG) is designed to use functional data and scan data selectively to eliminate the unnecessary clock toggling of flip-flops. With this structure, the self-gating function can be used in the scan test mode, as well as the function mode. When the self-gating logic is used during scan shift operations, the stuck-at faults in the self-gating logic can be tested with short test sequences; therefore, the rise in test costs can be mitigated. It is possible to test the stuck-at faults in self-gating logic using only four scan test patterns. The experimental results show that the average of the stuck-at test pattern increase ratio has been dropped from more than 90% to less than 8%. The low-power performance of the proposed method in the mission mode is the same as that of the conventional self-gating structures. When the DSSG method is used, the dynamic power of the shift operation which may increase excessively during the scan test can be reduced.