Cosimo Gerardi
Cosimo Gerardi has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Salvatore Lombardo
Institute for Microelectronics and Microsystems, National Research Council (CNR-IMM), Strada VIII, 5, 95121 Catania, Italy
4 shared publications - Marina Foti
Enel Green Power, Contrada Blocco Torrazze sn—Z.I., 95121 Catania, Italy
3 shared publications - Andrea Canino
Enel Green Power SpA,Rome,Italy,00198
2 shared publications - Fabio Ricco Galluzzo
Istituto per la Microelettronica e Microsistemi—Consiglio Nazionale delle Ricerche, Zona Industriale, Ottava Strada n. 5, 95121 Catania, Italy
2 shared publications - Marco Leonardi
Università degli Studi di Catania
2 shared publications - Rachela Gabriella Milazzo
Institute for Microelectronics and Microsystems, National Research Council (CNR-IMM), Strada VIII, 5, 95121 Catania, Italy
2 shared publications
Latest Publications
- 28 May 2023
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 257
Improvement of silicon heterojunction module efficiency using fast illumination post-treatments
- 28 May 2023
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 257
Improvement of silicon heterojunction module efficiency using fast illumination post-treatments
- Open Access
Evaluation of Voltage-Matched 2T Multi-Junction Modules Based on Monte Carlo Ray Tracing
As Si single-junction technology is approaching its Shockley–Queisser theoretical limit, relevant efforts are being expended towards the development of multi-junction modules. In this work, we employ an optical model based on Monte Carlo ray tracing to compare four different multi-junction modules in a voltage-matched two-terminal (VM2T) configuration. In particular, we took into consideration the VM2T coupling of crystalline silicon cells with CuInxGa1-xSe2 (CIGS), CdTe, GaAs and perovskite (PVK) solar cells. We optimized the thicknesses of each layer in the top sub-module and determined the performance of VM2T modules in the Shockley–Queisser theoretical limit. We also considered the possibility of using modules in which the top Si surface is flat to determine the performance drop due to the absence of the texturization on the top Si surface. Moreover, we determined the optimal bandgap energy of PVK in a VM2T PVK/Si module as well as the highest efficiency achievable. Lastly, we show that when using state-of-the-art cells, the highest VM2T efficiency achievable for the considered materials is 34.2% under standard test conditions.
Open AccessEvaluation of Voltage-Matched 2T Multi-Junction Modules Based on Monte Carlo Ray Tracing
As Si single-junction technology is approaching its Shockley–Queisser theoretical limit, relevant efforts are being expended towards the development of multi-junction modules. In this work, we employ an optical model based on Monte Carlo ray tracing to compare four different multi-junction modules in a voltage-matched two-terminal (VM2T) configuration. In particular, we took into consideration the VM2T coupling of crystalline silicon cells with CuInxGa1-xSe2 (CIGS), CdTe, GaAs and perovskite (PVK) solar cells. We optimized the thicknesses of each layer in the top sub-module and determined the performance of VM2T modules in the Shockley–Queisser theoretical limit. We also considered the possibility of using modules in which the top Si surface is flat to determine the performance drop due to the absence of the texturization on the top Si surface. Moreover, we determined the optimal bandgap energy of PVK in a VM2T PVK/Si module as well as the highest efficiency achievable. Lastly, we show that when using state-of-the-art cells, the highest VM2T efficiency achievable for the considered materials is 34.2% under standard test conditions.
- Open Access
The Effects of Module Temperature on the Energy Yield of Bifacial Photovoltaics: Data and Model
Bifacial photovoltaics (BPVs) are emerging with large momentum as promising solutions to improve energy yield and cost of PV systems. To reach its full potential, an accurate understanding of the physical characteristics of BPV technology is required. For this reason, we collected experimental data to refine a physical model of BPV. In particular, we simultaneously measured the module temperature, short circuit current (Isc), open-circuit voltage (Voc), power at the maximum power point (Pmpp), and the energy yield of a bifacial and a monofacial minimodule. Such minimodules, realised with the same geometry, cell technology, and module lamination, were tested under the same clear sky outdoor conditions, from morning to afternoon, for three days. The bifacial system experimentally shows higher module temperatures under operation, about 10 °C on a daily average of about 40 °C. Nevertheless, its energy yield is about 15% larger than the monofacial one. We propose a physical quantitative model that fits the experimental data of module temperature, Isc, Voc, Pmpp, and energy yield. The model was then applied to predict the annual energy yield of PV module strings. The effect of different PV module temperature coefficients on the energy yield is also discussed.
Open AccessThe Effects of Module Temperature on the Energy Yield of Bifacial Photovoltaics: Data and Model
Bifacial photovoltaics (BPVs) are emerging with large momentum as promising solutions to improve energy yield and cost of PV systems. To reach its full potential, an accurate understanding of the physical characteristics of BPV technology is required. For this reason, we collected experimental data to refine a physical model of BPV. In particular, we simultaneously measured the module temperature, short circuit current (Isc), open-circuit voltage (Voc), power at the maximum power point (Pmpp), and the energy yield of a bifacial and a monofacial minimodule. Such minimodules, realised with the same geometry, cell technology, and module lamination, were tested under the same clear sky outdoor conditions, from morning to afternoon, for three days. The bifacial system experimentally shows higher module temperatures under operation, about 10 °C on a daily average of about 40 °C. Nevertheless, its energy yield is about 15% larger than the monofacial one. We propose a physical quantitative model that fits the experimental data of module temperature, Isc, Voc, Pmpp, and energy yield. The model was then applied to predict the annual energy yield of PV module strings. The effect of different PV module temperature coefficients on the energy yield is also discussed.
- Open Access
Numerical Modeling of Bifacial PV String Performance: Perimeter Effect and Influence of Uniaxial Solar Trackers
The bifacial photovoltaic (PV) systems have recently met large interest. The performance of such systems heavily depends on the installation conditions and, in particular, on the albedo radiation collected by the module rear side. Therefore, it is of crucial importance to have an accurate performance model. To date, in the scientific literature, numerous models have been proposed and experimental data collected to study and optimize bifacial PV system performance. Currently, 3D and 2D models of bifacial PV devices exist. Though the former are more mathematically complex, they can lead to more accurate results, since they generally allow to fully consider the main aspects influencing a bifacial PV system performance. Recently, we have proposed and validated through experimental data a 3D model tested as a function of module height, tilt angle, and ground albedo. In this work, through such a model, we studied the role played by the perimeter zones surrounding the PV string, by considering PV strings of 30 or 60 modules. We considered the cases of fixed installation with optimal PV module tilt and of installation with uniaxial horizontal solar tracker. We evaluated the PV energy yield as a function of the size of the perimeter zones for the two cases, i.e., both with and without the solar tracker. In optimal perimeter conditions, we then studied the behavior of bifacial and mono-facial PV strings by varying the geographical location in a large latitude range.
Open AccessNumerical Modeling of Bifacial PV String Performance: Perimeter Effect and Influence of Uniaxial Solar Trackers
The bifacial photovoltaic (PV) systems have recently met large interest. The performance of such systems heavily depends on the installation conditions and, in particular, on the albedo radiation collected by the module rear side. Therefore, it is of crucial importance to have an accurate performance model. To date, in the scientific literature, numerous models have been proposed and experimental data collected to study and optimize bifacial PV system performance. Currently, 3D and 2D models of bifacial PV devices exist. Though the former are more mathematically complex, they can lead to more accurate results, since they generally allow to fully consider the main aspects influencing a bifacial PV system performance. Recently, we have proposed and validated through experimental data a 3D model tested as a function of module height, tilt angle, and ground albedo. In this work, through such a model, we studied the role played by the perimeter zones surrounding the PV string, by considering PV strings of 30 or 60 modules. We considered the cases of fixed installation with optimal PV module tilt and of installation with uniaxial horizontal solar tracker. We evaluated the PV energy yield as a function of the size of the perimeter zones for the two cases, i.e., both with and without the solar tracker. In optimal perimeter conditions, we then studied the behavior of bifacial and mono-facial PV strings by varying the geographical location in a large latitude range.
- Open Access
Reversible Efficiency Variation of Tandem Amorphous/Microcrystalline Si Photovoltaic Modules in Outdoor Operation
The Staebler-Wronski effect in amorphous silicon based photovoltaic devices is responsible for degradation of their power conversion efficiency, within approximately the first one thousand hours of light soaking. Several experimental studies led to highlight the performance instability phenomena for the mentioned devices, underling that recovery and improvement of such performance are observable, by subjecting such devices (both of single-junction and tandem types) to DC reverse bias stresses under illumination, or to operation in the Maximum Power Point (MPP) under variable conditions of temperature and illumination. In this work, we present and discuss the results of novel recent outdoor tests on stabilized specimens (i.e., exposed to 1000 h extended light soaking, before our tests) of tandem amorphous/microcrystalline Si (a-Si/µc-Si) photovoltaic (PV) minimodules operating in their MPP, by analyzing the causes of the performance instability effects, systematically observed on a daily scale. During the mentioned tests, we have monitored the solar cell operating temperature and the incident solar spectrum at various times in different days to verify the effect of cell temperature and solar spectrum changes on the cell performances. The experimental results show a clear correlation between performance improvements of the photovoltaic modules and their thermal history during the outdoor tests, proving the interplay between defect build-up at a lower temperature and defect annealing at a higher temperature, taking place in the solar cells operated in MPP during conventional outdoor operation.
Open AccessReversible Efficiency Variation of Tandem Amorphous/Microcrystalline Si Photovoltaic Modules in Outdoor Operation
The Staebler-Wronski effect in amorphous silicon based photovoltaic devices is responsible for degradation of their power conversion efficiency, within approximately the first one thousand hours of light soaking. Several experimental studies led to highlight the performance instability phenomena for the mentioned devices, underling that recovery and improvement of such performance are observable, by subjecting such devices (both of single-junction and tandem types) to DC reverse bias stresses under illumination, or to operation in the Maximum Power Point (MPP) under variable conditions of temperature and illumination. In this work, we present and discuss the results of novel recent outdoor tests on stabilized specimens (i.e., exposed to 1000 h extended light soaking, before our tests) of tandem amorphous/microcrystalline Si (a-Si/µc-Si) photovoltaic (PV) minimodules operating in their MPP, by analyzing the causes of the performance instability effects, systematically observed on a daily scale. During the mentioned tests, we have monitored the solar cell operating temperature and the incident solar spectrum at various times in different days to verify the effect of cell temperature and solar spectrum changes on the cell performances. The experimental results show a clear correlation between performance improvements of the photovoltaic modules and their thermal history during the outdoor tests, proving the interplay between defect build-up at a lower temperature and defect annealing at a higher temperature, taking place in the solar cells operated in MPP during conventional outdoor operation.