Hervé Kouamo Tchakouté
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hervé Kouamo Tchakouté has a total of 90 co-authors. Here are the top co-authors by number of shared publications:
Claus H. Rüscher
Institute of Mineralogy, Leibniz University Hanover, Callinstrasse 3, D-30167 Hanover, Germany
12 shared publicationsClaus Henning Rüscher
8 shared publicationsElie Kamseu
Local Materials Promotion Authority, Yaoundé, Cameroon
7 shared publications- Cristina Leonelli
Department of Engineering “Enzo Ferrari”, University of Modena and Reggio Emilia, 41125 Modena, Italy
6 shared publications Pengkun Hou
Shandong Provincial Key Laboratory for Preparation and Measurement of Building Materials, University of Jinan, Jinan, China
6 shared publicationsCharles Banenzoué
The University of Douala, Faculty of Science, Douala, Cameroon
4 shared publications
Latest Publications
- Open Access
- 1 October 2026
- Published by Springer Nature in Discover Civil Engineering
- Vol. 3 (1) , 238
Synergistic effect of silica sand particle size on the compressive strength and pore structure of geopolymers prepared from recycled fired clay brick waste
- 1 October 2026
- Published by Springer Nature in Discover Civil Engineering
- Vol. 3 (1) , 238
Open AccessSynergistic effect of silica sand particle size on the compressive strength and pore structure of geopolymers prepared from recycled fired clay brick waste
- Open Access
- 5 October 2025
- Published by Elsevier in Open Ceramics
- Vol. 24
Behavior of amorphous ferrisilicates with low weight concentration in ferric ions on the properties of metakaolin-based geopolymers
- 5 October 2025
- Published by Elsevier in Open Ceramics
- Vol. 24
Open AccessBehavior of amorphous ferrisilicates with low weight concentration in ferric ions on the properties of metakaolin-based geopolymers
- 1 October 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (9) , 8323-8346
Effects of Incorporating Ferric Ions from Hematite into Metakaolin on Microscopic Pore Structures and Compressive Strength of Geopolymers
- 1 October 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (9) , 8323-8346
Effects of Incorporating Ferric Ions from Hematite into Metakaolin on Microscopic Pore Structures and Compressive Strength of Geopolymers
- Open Access
- 10 December 2024
- Published by Springer Nature in Discover Civil Engineering
- Vol. 1 (1) , 1-17
Influence of CaO/Al2O3 molar ratio of synthetic calcium aluminate hydrates on the engineering properties of metakaolin-based alkali-activated materials
- 10 December 2024
- Published by Springer Nature in Discover Civil Engineering
- Vol. 1 (1) , 1-17
Open AccessInfluence of CaO/Al2O3 molar ratio of synthetic calcium aluminate hydrates on the engineering properties of metakaolin-based alkali-activated materials
- Open Access
- 24 May 2024
- Published by Universal Wiser Publisher Pte. Ltd in Engineering Science & Technology
- p. 405-417
Use of Commercial Starch, Starches Derived from Cassava, Potato, and Yam as Additives for Synthesising Metakaolin-Based Geopolymer Composites
The main objective of this work is to investigate the use of different starch sources (yam, sweet potato, cassava, and commercial starch) as additives for the production of metakaolin-based geopolymer composites. Geopolymer composites were prepared by replacing metakaolin with 0 and 15 wt% of each type of starch. The different powders obtained were separately mixed with a hardener containing a molar ratio of SiO2/Na2O of 1.6. X-ray diffraction and Fourier transform infrared spectroscopy analysis were used to determine the structural properties. The compressive strength and morphology of the prepared geopolymer composites were investigated. Results show that the reference geopolymer compressive strength is 36.25 MPa. These are 64.66, 48.49, 46.03, and 44.71 MPa when commercial starch, yam starch, cassava starch, and sweet potato starch, respectively have been used as additives. It can be seen that the compressive strength values of the geopolymers containing starches are higher than those of the reference geopolymer. The compressive strength of the geopolymer composite made by replacing metakaolin with commercial starch is higher than those made with yam starch, cassava starch, and sweet potato starch. The X-ray patterns of all the geopolymers show the same mineral and the infrared spectra show the same absorption bands, except for the one at 2,935 cm-1 which appears on the spectra of the geopolymers containing starch. The geopolymer composite containing commercial starch has a more compact and dense microstructure. Those containing starches from yam, cassava, sweet potato, and the reference geopolymer material have a coarser microstructure. Compressive strength is consistent with the more compact and dense microstructure of geopolymer composite containing commercial starch. The incorporation of 15 wt% of starches derived from yam, cassava, sweet potato, and commercial starch was found to increase compressive strength. It was found that starches from various crops could be used as additives in the synthesis of geopolymer composites.
- 24 May 2024
- Published by Universal Wiser Publisher Pte. Ltd in Engineering Science & Technology
- p. 405-417
Open AccessUse of Commercial Starch, Starches Derived from Cassava, Potato, and Yam as Additives for Synthesising Metakaolin-Based Geopolymer Composites
The main objective of this work is to investigate the use of different starch sources (yam, sweet potato, cassava, and commercial starch) as additives for the production of metakaolin-based geopolymer composites. Geopolymer composites were prepared by replacing metakaolin with 0 and 15 wt% of each type of starch. The different powders obtained were separately mixed with a hardener containing a molar ratio of SiO2/Na2O of 1.6. X-ray diffraction and Fourier transform infrared spectroscopy analysis were used to determine the structural properties. The compressive strength and morphology of the prepared geopolymer composites were investigated. Results show that the reference geopolymer compressive strength is 36.25 MPa. These are 64.66, 48.49, 46.03, and 44.71 MPa when commercial starch, yam starch, cassava starch, and sweet potato starch, respectively have been used as additives. It can be seen that the compressive strength values of the geopolymers containing starches are higher than those of the reference geopolymer. The compressive strength of the geopolymer composite made by replacing metakaolin with commercial starch is higher than those made with yam starch, cassava starch, and sweet potato starch. The X-ray patterns of all the geopolymers show the same mineral and the infrared spectra show the same absorption bands, except for the one at 2,935 cm-1 which appears on the spectra of the geopolymers containing starch. The geopolymer composite containing commercial starch has a more compact and dense microstructure. Those containing starches from yam, cassava, sweet potato, and the reference geopolymer material have a coarser microstructure. Compressive strength is consistent with the more compact and dense microstructure of geopolymer composite containing commercial starch. The incorporation of 15 wt% of starches derived from yam, cassava, sweet potato, and commercial starch was found to increase compressive strength. It was found that starches from various crops could be used as additives in the synthesis of geopolymer composites.
- Open Access
- 16 May 2024
- Published by Universal Wiser Publisher Pte. Ltd in Sustainable Chemical Engineering
- p. 332-351
Microstructure and Compressive Strength of Geopolymer Materials Based on Metakaolin with Hematite and Magnetite Gels as Additives
The purpose of this work is to increase the compressive strength and improve the microstructure of geopolymer materials by adding hematite and magnetite gels, as well as their powders, cured at 80 °C. Hematite and magnetite are dissolved in 10 M sodium hydroxide. Dried gels of hematite and magnetite were then ground to produce powders of dissolved hematite and magnetite. For the production of various geopolymer materials, the metakaolin was replaced by 0 and 10 wt. % of each additive and then mixed with the hardener containing the SiO2/Na2O molar ratio set at 1.6. The results show that the reference geopolymer has a compressive strength of 51.11 MPa. These values are 50.99 and 47.59 MPa for the geopolymer materials with 10 wt. % of dissolved magnetite gel and the powder of dissolved magnetite cured at 80 °C, respectively. They are 59.52 and 63.23 MPa for those prepared using 10 wt. % of dissolved hematite gel and for the powder of dissolved hematite cured at 80 °C, respectively. Si, Al, Fe, Na and Ti form a homogeneous phase in the geopolymer structures with the exception of a few magnetite particles agglomerated in the geopolymer materials. Compressive strength was found to be improved by the use of hematite gel and dissolved hematite powder cured at 80 °C as additives. A slight reduction in the compressive strength was observed when the dissolved magnetite gel and the powder of the dissolved magnetite cured at 80 °C were used as additives.
- 16 May 2024
- Published by Universal Wiser Publisher Pte. Ltd in Sustainable Chemical Engineering
- p. 332-351
Open AccessMicrostructure and Compressive Strength of Geopolymer Materials Based on Metakaolin with Hematite and Magnetite Gels as Additives
The purpose of this work is to increase the compressive strength and improve the microstructure of geopolymer materials by adding hematite and magnetite gels, as well as their powders, cured at 80 °C. Hematite and magnetite are dissolved in 10 M sodium hydroxide. Dried gels of hematite and magnetite were then ground to produce powders of dissolved hematite and magnetite. For the production of various geopolymer materials, the metakaolin was replaced by 0 and 10 wt. % of each additive and then mixed with the hardener containing the SiO2/Na2O molar ratio set at 1.6. The results show that the reference geopolymer has a compressive strength of 51.11 MPa. These values are 50.99 and 47.59 MPa for the geopolymer materials with 10 wt. % of dissolved magnetite gel and the powder of dissolved magnetite cured at 80 °C, respectively. They are 59.52 and 63.23 MPa for those prepared using 10 wt. % of dissolved hematite gel and for the powder of dissolved hematite cured at 80 °C, respectively. Si, Al, Fe, Na and Ti form a homogeneous phase in the geopolymer structures with the exception of a few magnetite particles agglomerated in the geopolymer materials. Compressive strength was found to be improved by the use of hematite gel and dissolved hematite powder cured at 80 °C as additives. A slight reduction in the compressive strength was observed when the dissolved magnetite gel and the powder of the dissolved magnetite cured at 80 °C were used as additives.
- Open Access
- 7 March 2024
- Published by Universal Wiser Publisher Pte. Ltd in Engineering Science & Technology
- p. 180-194
Influence of Starch Powder on Compressive Strength and Microstructural Properties of Geopolymer Composite Materials Based on Metakaolin
The main objective of the present study is the investigation of the behaviour of starch powder incorporated at different levels (0, 5, 10, 15, 20, 25, and 30 wt%) on the compressive strength and microstructural properties of metakaolin-based geopolymers. Sodium silicate with a molar ratio of SiO2/Na2O of 1.6 was used as the hardener and standard metakaolin was used as the aluminosilicate source. The results showed that when metakaolin was replaced by starch from 0 to 15 wt%, the compressive strength increased from 36.50 to 64.12 MPa. When metakaolin was replaced by starch above 15 wt%, the compressive strength decreased from 64.12 to 29.43 MPa. That of the reference geopolymer material is 36.50 MPa.The infrared spectra of the geopolymer composites indicate that the Si-O-C bonds are formed. The thermal behaviour of geopolymer composites containing starch shows a mass loss at around 100 and 278 °C. The geopolymer material without starch only shows a loss of mass at around 100 °C. The micrographs of the geopolymer composite with 15% by weight of starch show that the matrix is more compact, more homogeneous, and denser than the one without starch. On the contrary, possibly due to a large amount of unreacted starch in its network, the micrographs of the geopolymer composite obtained after the incorporation of 30 wt% starch show a heterogeneous microstructure. It can be concluded that suitable starch content for the synthesis of geopolymer composites would be around 15% by weight.
- 7 March 2024
- Published by Universal Wiser Publisher Pte. Ltd in Engineering Science & Technology
- p. 180-194
Open AccessInfluence of Starch Powder on Compressive Strength and Microstructural Properties of Geopolymer Composite Materials Based on Metakaolin
The main objective of the present study is the investigation of the behaviour of starch powder incorporated at different levels (0, 5, 10, 15, 20, 25, and 30 wt%) on the compressive strength and microstructural properties of metakaolin-based geopolymers. Sodium silicate with a molar ratio of SiO2/Na2O of 1.6 was used as the hardener and standard metakaolin was used as the aluminosilicate source. The results showed that when metakaolin was replaced by starch from 0 to 15 wt%, the compressive strength increased from 36.50 to 64.12 MPa. When metakaolin was replaced by starch above 15 wt%, the compressive strength decreased from 64.12 to 29.43 MPa. That of the reference geopolymer material is 36.50 MPa.The infrared spectra of the geopolymer composites indicate that the Si-O-C bonds are formed. The thermal behaviour of geopolymer composites containing starch shows a mass loss at around 100 and 278 °C. The geopolymer material without starch only shows a loss of mass at around 100 °C. The micrographs of the geopolymer composite with 15% by weight of starch show that the matrix is more compact, more homogeneous, and denser than the one without starch. On the contrary, possibly due to a large amount of unreacted starch in its network, the micrographs of the geopolymer composite obtained after the incorporation of 30 wt% starch show a heterogeneous microstructure. It can be concluded that suitable starch content for the synthesis of geopolymer composites would be around 15% by weight.
- Open Access
- 23 January 2024
- Published by Universal Wiser Publisher Pte. Ltd in Engineering Science & Technology
- p. 136-157
Investigation of the Properties of Metakaolin-Based Geopolymer Materials Using Ferrisilicates as Additives Synthesised in Sodium Hydroxide Solution or Distilled Water
The main objective of this work is to investigate the behaviour of ferrisilicates prepared from hematite and two silica sources (rice husk ash and silica fume) on the compressive strength of geopolymer materials. Some ferrisilicates were synthesised in 2M sodium hydroxide solution. Others were prepared using distilled water as a solvent. The Fe2O3/SiO2 molar ratio contained in the ferrisilicates is set to 0.2. Metakaolin and sodium silicate solution with a molar ratio of SiO2/Na2O of 1.6 were used as the aluminosilicate and hardener in this work. The control geopolymer compressive strength is 53.34 MPa. For ferrisilicates prepared in alkaline solution using rice husk ash and silica fume, their compressive strength values are 71.91 and 77.72 MPa, respectively. The compressive strengths of the geopolymer materials made from ferrisilicates prepared in distilled water using rice husk ash and silica fume are 74.13 and 44.73 MPa, respectively. In the presence of ferrisilicate obtained by dissolving silica fume and hematite in sodium hydroxide solution, the maximum compressive strength of 77.72 MPa was obtained. When ferrisilicates from the mixture of silica fume, hematite, and distilled water are used as an additive, the minimum compressive strength of 43.73 MPa is achieved. It can be concluded that additives synthesised in an alkaline medium and those obtained in distilled water with rice husk ash improve compressive strength. On the other hand, the compressive strength of the geopolymer material that uses the additive produced with silica fume in distilled water is lower (44.73 MPa).
- 23 January 2024
- Published by Universal Wiser Publisher Pte. Ltd in Engineering Science & Technology
- p. 136-157
Open AccessInvestigation of the Properties of Metakaolin-Based Geopolymer Materials Using Ferrisilicates as Additives Synthesised in Sodium Hydroxide Solution or Distilled Water
The main objective of this work is to investigate the behaviour of ferrisilicates prepared from hematite and two silica sources (rice husk ash and silica fume) on the compressive strength of geopolymer materials. Some ferrisilicates were synthesised in 2M sodium hydroxide solution. Others were prepared using distilled water as a solvent. The Fe2O3/SiO2 molar ratio contained in the ferrisilicates is set to 0.2. Metakaolin and sodium silicate solution with a molar ratio of SiO2/Na2O of 1.6 were used as the aluminosilicate and hardener in this work. The control geopolymer compressive strength is 53.34 MPa. For ferrisilicates prepared in alkaline solution using rice husk ash and silica fume, their compressive strength values are 71.91 and 77.72 MPa, respectively. The compressive strengths of the geopolymer materials made from ferrisilicates prepared in distilled water using rice husk ash and silica fume are 74.13 and 44.73 MPa, respectively. In the presence of ferrisilicate obtained by dissolving silica fume and hematite in sodium hydroxide solution, the maximum compressive strength of 77.72 MPa was obtained. When ferrisilicates from the mixture of silica fume, hematite, and distilled water are used as an additive, the minimum compressive strength of 43.73 MPa is achieved. It can be concluded that additives synthesised in an alkaline medium and those obtained in distilled water with rice husk ash improve compressive strength. On the other hand, the compressive strength of the geopolymer material that uses the additive produced with silica fume in distilled water is lower (44.73 MPa).