Cheng-Hsien Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Cheng-Hsien Wu has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Cheng-Hao Chiu
Department of Mold and Die Engineering, National Kaohsiung University of Science and Technology, Kaohsiung, Taiwan
1 shared publicationCheng‐Long Yu
Department of Mold and Die Engineering National Kaohsiung University of Science and Technology Kaohsiung Taiwan
1 shared publicationChieh Lee
1 shared publication- Chun-Liang Yeh
Department of Mold and Die Engineering, National Kaohsiung University of Science and Technology, Kaohsiung, Taiwan
1 shared publication - Chun-Yu Liu
Department of Mold and Die Engineering, National Kaohsiung University of Science and Technology, Kaohsiung, Taiwan
1 shared publication Ji‐Huan Li
Department of Mold and Die Engineering National Kaohsiung University of Science and Technology Kaohsiung Taiwan
1 shared publication
Latest Publications
- 24 July 2026
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 174, 335-354
A rapid interchangeable-insert injection mold with in-press fine alignment: Design and experimental validation
- 24 July 2026
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 174, 335-354
A rapid interchangeable-insert injection mold with in-press fine alignment: Design and experimental validation
- 17 April 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 144 (5-6) , 3633-3652
Roll-to-roll UV embossing of surface relief gratings using multi-objective optimization for AR waveguides
- 17 April 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 144 (5-6) , 3633-3652
Roll-to-roll UV embossing of surface relief gratings using multi-objective optimization for AR waveguides
- 13 March 2026
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (5) , 3626-3639
Roll‐to‐Roll UV Embossing and Pressure Thermoforming of PET Films for Spherical Fresnel Lenses in Photovoltaic Applications
Integrating Fresnel lenses into photovoltaic (PV) systems can reduce the required solar‐cell area and enhance conversion efficiency by concentrating incident sunlight onto the cell surface. In this study, planar and spherical Fresnel lenses were designed and optimized through optical simulations to develop high‐concentration lenses for PV applications. The simulations indicated that a spherical Fresnel lens with a curvature radius of 250 mm provided the highest illumination. However, conventional mass production of spherical Fresnel lenses remains cost‐prohibitive due to the complexity and expense of machining spherical molds. To overcome this limitation, we propose an innovative and cost‐effective fabrication method that reduces mold manufacturing costs and simplifies the production workflow. The process employs roll‐to‐roll UV embossing as the initial patterning step, followed by pressure‐assisted thermoforming to reshape the patterned film into a spherical form. The Taguchi method was used to optimize key process parameters, including resin temperature, film speed, film‐press pressure, and film tension. Among these, film tension had the most significant effect on the structural fidelity of the Fresnel features. In the thermoforming stage, six groups of spherical Fresnel lenses were produced under varying conditions, and their PV performance was evaluated using a solar simulator. The results showed that the PV conversion efficiency increased from 8.88% (bare solar cell) to 56.73% when using the planar Fresnel lens, corresponding to 6.39× the bare‐cell value. Furthermore, the spherical Fresnel lens provided an additional 23% improvement over the planar lens. These results demonstrate that the proposed hybrid process enables the fabrication of functional polymer‐based Fresnel lenses and effectively enhances PV performance.
- 13 March 2026
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (5) , 3626-3639
Roll‐to‐Roll UV Embossing and Pressure Thermoforming of PET Films for Spherical Fresnel Lenses in Photovoltaic Applications
Integrating Fresnel lenses into photovoltaic (PV) systems can reduce the required solar‐cell area and enhance conversion efficiency by concentrating incident sunlight onto the cell surface. In this study, planar and spherical Fresnel lenses were designed and optimized through optical simulations to develop high‐concentration lenses for PV applications. The simulations indicated that a spherical Fresnel lens with a curvature radius of 250 mm provided the highest illumination. However, conventional mass production of spherical Fresnel lenses remains cost‐prohibitive due to the complexity and expense of machining spherical molds. To overcome this limitation, we propose an innovative and cost‐effective fabrication method that reduces mold manufacturing costs and simplifies the production workflow. The process employs roll‐to‐roll UV embossing as the initial patterning step, followed by pressure‐assisted thermoforming to reshape the patterned film into a spherical form. The Taguchi method was used to optimize key process parameters, including resin temperature, film speed, film‐press pressure, and film tension. Among these, film tension had the most significant effect on the structural fidelity of the Fresnel features. In the thermoforming stage, six groups of spherical Fresnel lenses were produced under varying conditions, and their PV performance was evaluated using a solar simulator. The results showed that the PV conversion efficiency increased from 8.88% (bare solar cell) to 56.73% when using the planar Fresnel lens, corresponding to 6.39× the bare‐cell value. Furthermore, the spherical Fresnel lens provided an additional 23% improvement over the planar lens. These results demonstrate that the proposed hybrid process enables the fabrication of functional polymer‐based Fresnel lenses and effectively enhances PV performance.
- 27 November 2025
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (2) , 1170-1185
Fabrication and Optimization of Roll‐To‐Roll UV ‐Embossed Microlens Array– PDLC Films for Enhanced Light Extraction in OLED Panels
This study presents developing and optimizing a roll‐to‐roll (R2R) UV embossing process for high‐volume, low‐cost fabrication of microlens array–polymer dispersed liquid crystal (MLA‐PDLC) composite films. The relative influence of process parameters was systematically quantified by employing Taguchi experimental design. Film‐press pressure was identified as the dominant factor governing replication fidelity, followed by film tension and resin temperature, while film speed had minimal effect. Optimized conditions (resin temperature 25°C, film speed 0.6 m/min, press pressure 190 MPa, and tension 40 N) yielded replication fidelity of 96.2%, with only 1.49% deviation from prediction, confirming the robustness and reproducibility of the process optimization. A more economical approach was introduced to address the cost and scalability limitations of conventional embossing roller fabrication by combining 3D‐printed masters with a polydimethylsiloxane (PDMS) soft mold laminated onto the roller surface. This strategy significantly reduces tooling costs while maintaining high replication accuracy, demonstrating strong potential for industrial‐scale deployment. Validation on OLED lighting panels confirmed the practical benefits of the optimized MLA‐PDLC films, including enhanced luminous flux, luminance, and illuminance uniformity. These results highlight that achieving high replication fidelity is critical for optical performance and establishing a reliable, scalable, and cost‐effective manufacturing route for advanced microstructured films.
- 27 November 2025
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (2) , 1170-1185
Fabrication and Optimization of Roll‐To‐Roll UV ‐Embossed Microlens Array– PDLC Films for Enhanced Light Extraction in OLED Panels
This study presents developing and optimizing a roll‐to‐roll (R2R) UV embossing process for high‐volume, low‐cost fabrication of microlens array–polymer dispersed liquid crystal (MLA‐PDLC) composite films. The relative influence of process parameters was systematically quantified by employing Taguchi experimental design. Film‐press pressure was identified as the dominant factor governing replication fidelity, followed by film tension and resin temperature, while film speed had minimal effect. Optimized conditions (resin temperature 25°C, film speed 0.6 m/min, press pressure 190 MPa, and tension 40 N) yielded replication fidelity of 96.2%, with only 1.49% deviation from prediction, confirming the robustness and reproducibility of the process optimization. A more economical approach was introduced to address the cost and scalability limitations of conventional embossing roller fabrication by combining 3D‐printed masters with a polydimethylsiloxane (PDMS) soft mold laminated onto the roller surface. This strategy significantly reduces tooling costs while maintaining high replication accuracy, demonstrating strong potential for industrial‐scale deployment. Validation on OLED lighting panels confirmed the practical benefits of the optimized MLA‐PDLC films, including enhanced luminous flux, luminance, and illuminance uniformity. These results highlight that achieving high replication fidelity is critical for optical performance and establishing a reliable, scalable, and cost‐effective manufacturing route for advanced microstructured films.
- 16 March 2025
- Published by Wiley in Polymer Engineering & Science
- Vol. 65 (5) , 2624-2641
Multi‐objective optimization in roll‐to‐roll UV embossing for manufacturing linear Fresnel lenses
Linear Fresnel lenses are widely used in solar energy concentration, image processing, and optical imaging applications. Concentrated solar power technology offers a more efficient and economical solution by focusing sunlight onto a smaller receiver, thereby increasing energy conversion efficiency and reducing facility costs. This research aims to design and manufacture a concentrating lens that can achieve the most uniform illumination and the lowest energy loss percentage. The optical design of the linear Fresnel lens aims for maximum uniformity and minimal energy loss. The lens parameters include a lens area, a focal length, and a structure spacing. Roll‐to‐roll UV embossing was applied to produce the linear Fresnel lenses. Four embossing parameters: resin pressure, film speed, film‐press pressure, and film tension, were optimized. The design optimization uses the Taguchi method and multi‐objective response surface methodology (RSM), which are applied to the optical design and process parameter analysis. The results show that optimized parameter combinations can significantly improve the replication percentage of the lens structure and reduce surface bubble defects. In addition, the linear Fresnel lens was tested on solar cells. The highest quality lenses are manufactured under multi‐objective optimization conditions.Highlights: Multi‐objective optimization design using response surface methodology. Applying linear Fresnel lenses to solar cells increases output power. Optimized Fresnel lens design achieves uniform illumination and low energy loss. Roll‐to‐roll UV embossing makes Fresnel lenses with excellent light focus.
- 16 March 2025
- Published by Wiley in Polymer Engineering & Science
- Vol. 65 (5) , 2624-2641
Multi‐objective optimization in roll‐to‐roll UV embossing for manufacturing linear Fresnel lenses
Linear Fresnel lenses are widely used in solar energy concentration, image processing, and optical imaging applications. Concentrated solar power technology offers a more efficient and economical solution by focusing sunlight onto a smaller receiver, thereby increasing energy conversion efficiency and reducing facility costs. This research aims to design and manufacture a concentrating lens that can achieve the most uniform illumination and the lowest energy loss percentage. The optical design of the linear Fresnel lens aims for maximum uniformity and minimal energy loss. The lens parameters include a lens area, a focal length, and a structure spacing. Roll‐to‐roll UV embossing was applied to produce the linear Fresnel lenses. Four embossing parameters: resin pressure, film speed, film‐press pressure, and film tension, were optimized. The design optimization uses the Taguchi method and multi‐objective response surface methodology (RSM), which are applied to the optical design and process parameter analysis. The results show that optimized parameter combinations can significantly improve the replication percentage of the lens structure and reduce surface bubble defects. In addition, the linear Fresnel lens was tested on solar cells. The highest quality lenses are manufactured under multi‐objective optimization conditions.Highlights: Multi‐objective optimization design using response surface methodology. Applying linear Fresnel lenses to solar cells increases output power. Optimized Fresnel lens design achieves uniform illumination and low energy loss. Roll‐to‐roll UV embossing makes Fresnel lenses with excellent light focus.
- 8 November 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (9-10) , 4471-4490
Parameter analysis of multi-objective optimization for energy efficiency and multiple quality aspects in injection molding
- 8 November 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (9-10) , 4471-4490
Parameter analysis of multi-objective optimization for energy efficiency and multiple quality aspects in injection molding
- 13 February 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 125 (11-12) , 5089-5099
Optimization of compression molding for double-concave lenses
- 13 February 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 125 (11-12) , 5089-5099
Optimization of compression molding for double-concave lenses
- 4 April 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (9-10) , 5955-5967
Deep learning-based optimization using a limited number of experiments for roll-to-roll UV embossing
- 4 April 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (9-10) , 5955-5967
Deep learning-based optimization using a limited number of experiments for roll-to-roll UV embossing