Ting Yuan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ting Yuan has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Aibin Ma
College of Materials Science and Engineering, Hohai University, Nanjing 210098, China
2 shared publications - Jinghua Jiang
College of Materials Science and Engineering, Hohai University, Jintan, China
2 shared publications - Yuna Wu
College of Materials Science and Engineering, Hohai University, Changzhou 213000, China
2 shared publications Chengcheng Han
College of Materials Science and Engineering, Hohai University, Changzhou, China
1 shared publication- Fei Geng
Changshu Institute of Technology, Changshu, Jiangsu, China
1 shared publication Feng Fang
School of Materials Science and Engineering, Southeast University, Nanjing, China
1 shared publication
Latest Publications
- 25 September 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (8) , 7677-7690
Silicon Morphology Control and Performance of Hypereutectic Al-Si Alloys: A Study on Divorced Versus Coupled Growth
- 25 September 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (8) , 7677-7690
Silicon Morphology Control and Performance of Hypereutectic Al-Si Alloys: A Study on Divorced Versus Coupled Growth
- Open Access
- 22 August 2024
- Published by MDPI AG in Preprints.org
Severe Plastic Deformation Significantly Enhances Strengthening and Toughening Effect of T6 Treated 7046 Aluminum Alloy
7046 aluminum alloy has good fatigue property, corrosion resistance and weld property, but the moderate strength and plasticity limit its wider application and development. In the present study, severe plastic deformation (SPD) was applied prior to T6 treatment to significantly strengthen and toughen the 7046 aluminum alloy. Results indicate that the alloy processed by 4 passes of equal channel angular pressing (ECAP) at 300 ℃ prior to T6 treatment exhibits an excellent mechanical performance, with ultimate tensile strength (UTS) and elongation (EL) of 485 MPa and 19%, exhibiting an improvement of 18.6% and 375% compared to that of the T6 alloy, respectively. The mechanical properties of the alloy are further improved by the additional room temperature (RT) rolling process, with UTS of 508 MPa and EL of 23.4%. There are more precipitates of η' and Al6Mn phases in the 300℃4P-R80%-T6 and 300°C4P-T6 alloys, which contribute to the strengthening and toughening enhancement by SPD processed T6 alloy. The results of this work may shed some light on enhancing 7046 aluminum alloy.
- 22 August 2024
- Published by MDPI AG in Preprints.org
Open AccessSevere Plastic Deformation Significantly Enhances Strengthening and Toughening Effect of T6 Treated 7046 Aluminum Alloy
7046 aluminum alloy has good fatigue property, corrosion resistance and weld property, but the moderate strength and plasticity limit its wider application and development. In the present study, severe plastic deformation (SPD) was applied prior to T6 treatment to significantly strengthen and toughen the 7046 aluminum alloy. Results indicate that the alloy processed by 4 passes of equal channel angular pressing (ECAP) at 300 ℃ prior to T6 treatment exhibits an excellent mechanical performance, with ultimate tensile strength (UTS) and elongation (EL) of 485 MPa and 19%, exhibiting an improvement of 18.6% and 375% compared to that of the T6 alloy, respectively. The mechanical properties of the alloy are further improved by the additional room temperature (RT) rolling process, with UTS of 508 MPa and EL of 23.4%. There are more precipitates of η' and Al6Mn phases in the 300℃4P-R80%-T6 and 300°C4P-T6 alloys, which contribute to the strengthening and toughening enhancement by SPD processed T6 alloy. The results of this work may shed some light on enhancing 7046 aluminum alloy.
- 30 November 2020
- Published by Springer Nature in Journal of Materials Science
- Vol. 56 (8) , 5215-5232
Gradient multilayer aluminium sheets used in automotive heat exchangers
- 30 November 2020
- Published by Springer Nature in Journal of Materials Science
- Vol. 56 (8) , 5215-5232
Gradient multilayer aluminium sheets used in automotive heat exchangers
- Open Access
Cooperative Effect of Li Content and Equal-Channel Angular Pressing on Microstructure and Mechanical Properties of Al-Mg-Li Alloy
This paper investigated the cooperative effects of Li addition and warm Equal Channel Angular Pressing (ECAP) on improving the mechanical properties of an Al-Mg-Li alloy for further weight reduction. The results showed that more Li addition could obviously refine the grains of the as-cast alloy and reduce its density value to only 2.37 g/cm3 when Li content reached 2.5% (about 12.6% lighter than commercial Al alloys). It also had a pronounced influence on the precipitations in the Al-5.5Mg-xLi-0.1Zr alloy, i.e., the number density and size of Al2MgLi and δ’-Al3Li phases. The yield strength of the as-cast alloy was increased with increasing Li, but the elongation deteriorated due to primary network intergranular Al2MgLi and more δ’ particles in the high Li-containing alloy. The warm multi-pass ECAP process was found to simultaneously improve the strength and ductility of the Al-Mg-Li alloys, and greatly alleviate the detrimental effect of Li addition on the elongation, thereby making the ultrafine-grained (UFG) alloys, a good combination of lightweight and high performance, very attractive for aerospace applications for much higher specific strength than both Al matrix composites and Mg alloys.
Open AccessCooperative Effect of Li Content and Equal-Channel Angular Pressing on Microstructure and Mechanical Properties of Al-Mg-Li Alloy
This paper investigated the cooperative effects of Li addition and warm Equal Channel Angular Pressing (ECAP) on improving the mechanical properties of an Al-Mg-Li alloy for further weight reduction. The results showed that more Li addition could obviously refine the grains of the as-cast alloy and reduce its density value to only 2.37 g/cm3 when Li content reached 2.5% (about 12.6% lighter than commercial Al alloys). It also had a pronounced influence on the precipitations in the Al-5.5Mg-xLi-0.1Zr alloy, i.e., the number density and size of Al2MgLi and δ’-Al3Li phases. The yield strength of the as-cast alloy was increased with increasing Li, but the elongation deteriorated due to primary network intergranular Al2MgLi and more δ’ particles in the high Li-containing alloy. The warm multi-pass ECAP process was found to simultaneously improve the strength and ductility of the Al-Mg-Li alloys, and greatly alleviate the detrimental effect of Li addition on the elongation, thereby making the ultrafine-grained (UFG) alloys, a good combination of lightweight and high performance, very attractive for aerospace applications for much higher specific strength than both Al matrix composites and Mg alloys.
- 6 November 2017
- Published by Emerald Publishing in Anti-Corrosion Methods and Materials
- Vol. 64 (6) , 664-671
The brazing effect on the corrosion mechanism of a multilayer material with Cu
Purpose: The purpose of this paper is to compare corrosion behavior of a modified multilayer material with Cu before and after brazing process. Design/methodology/approach: Sea water acidified accelerated tests (SWAATs), potentiodynamic polarization tests and scanning electron microscopy were used to study the corrosion behavior and macro/micro structures. Results indicate that the corrosion mechanisms of the sheets before and after brazing process are completely different. Findings: The un-brazed material is uniform corrosion, while the brazed material has a high sensitivity to localized corrosion and loses cathodic protection to the core. It is found that brazing process causes copper transition from the core alloy into eutectic phases in the cladding, leading to higher Ecorr and different potential distribution compared with those of un-brazed materials. Originality/value: For the modified multilayer material after brazing, there are two stages of corrosion. First, corrosion attack takes place along eutectic phases in the cladding material, and then core alloy dissolves by forming a galvanic couple with the nobler residual cladding.
- 6 November 2017
- Published by Emerald Publishing in Anti-Corrosion Methods and Materials
- Vol. 64 (6) , 664-671
The brazing effect on the corrosion mechanism of a multilayer material with Cu
Purpose: The purpose of this paper is to compare corrosion behavior of a modified multilayer material with Cu before and after brazing process. Design/methodology/approach: Sea water acidified accelerated tests (SWAATs), potentiodynamic polarization tests and scanning electron microscopy were used to study the corrosion behavior and macro/micro structures. Results indicate that the corrosion mechanisms of the sheets before and after brazing process are completely different. Findings: The un-brazed material is uniform corrosion, while the brazed material has a high sensitivity to localized corrosion and loses cathodic protection to the core. It is found that brazing process causes copper transition from the core alloy into eutectic phases in the cladding, leading to higher Ecorr and different potential distribution compared with those of un-brazed materials. Originality/value: For the modified multilayer material after brazing, there are two stages of corrosion. First, corrosion attack takes place along eutectic phases in the cladding material, and then core alloy dissolves by forming a galvanic couple with the nobler residual cladding.