Leila Sorkhi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Leila Sorkhi has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Taghi Shahrabi
Department of Materials Engineering, Faculty of Engineering, Tarbiat Modares University, P.O. Box: 14115-143, Tehran, Iran
3 shared publications M. Farrokhi-Rad
1 shared publication- Morteza Farrokhi-Rad
Azarbaijan Shahid Madani University, Tabriz, Iran (the Islamic Republic of)
1 shared publication - Morteza Farrokhi-Rad
Tarbiat Modares University
1 shared publication S. Mahmoodi
1 shared publication
Latest Publications
- Open Access
Electrophoretic Deposition of Hydroxyapatite–Chitosan–Titania on Stainless Steel 316 L
In this research, hydroxyapatite (HA)–chitosan–titania nanocomposite coatings were formed on 316 L stainless steel using electrophoretic deposition (EPD) from alcoholic (methanol and ethanol) suspensions containing 0.5 g/L chitosan and 2 and 5 g/L HA and 2 and 5 g/L Titania. The effect of different parameters on the deposition rate, morphology, and corrosion resistance of the coatings in simulated body fluid (SBF) at 37 °C has been studied. The coatings’ properties were investigated using Fourier-transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM). Based on the results of this work, it was found that the deposition rate in ethanolic suspensions is lower than methanolic ones. Moreover, the coating surface was smoother when the ethanol was used as a solvent in suspensions in comparison to the ones where methanol was the solvent. The coating deposited from a suspension containing 0.5 g/L chitosan, 2 g/L HA, and 5 g/L titania with ethanol as solvent had the highest corrosion resistance in SBF at 37 °C.
Open AccessElectrophoretic Deposition of Hydroxyapatite–Chitosan–Titania on Stainless Steel 316 L
In this research, hydroxyapatite (HA)–chitosan–titania nanocomposite coatings were formed on 316 L stainless steel using electrophoretic deposition (EPD) from alcoholic (methanol and ethanol) suspensions containing 0.5 g/L chitosan and 2 and 5 g/L HA and 2 and 5 g/L Titania. The effect of different parameters on the deposition rate, morphology, and corrosion resistance of the coatings in simulated body fluid (SBF) at 37 °C has been studied. The coatings’ properties were investigated using Fourier-transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM). Based on the results of this work, it was found that the deposition rate in ethanolic suspensions is lower than methanolic ones. Moreover, the coating surface was smoother when the ethanol was used as a solvent in suspensions in comparison to the ones where methanol was the solvent. The coating deposited from a suspension containing 0.5 g/L chitosan, 2 g/L HA, and 5 g/L titania with ethanol as solvent had the highest corrosion resistance in SBF at 37 °C.
- 23 April 2014
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 11 (5) , 739-746
Electrophoretic deposition of chitosan in different alcohols
- 23 April 2014
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 11 (5) , 739-746
Electrophoretic deposition of chitosan in different alcohols
- 1 February 2013
- Published by Elsevier in Surface and Coatings Technology
- Vol. 216, 106-114
Electrophoretic deposition of hydroxyapatite–chitosan nanocomposite coatings in different alcohols
- 1 February 2013
- Published by Elsevier in Surface and Coatings Technology
- Vol. 216, 106-114
Electrophoretic deposition of hydroxyapatite–chitosan nanocomposite coatings in different alcohols