Shigeng Zhong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shigeng Zhong has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Jianqiang Liu
School of Electrical Engineering, Beijing Jiaotong University, Beijing 100044, China
2 shared publications - Jiepin Zhang
Beijing China 100044
2 shared publications - Jingxi Yang
Department of Electrical Engineering, City University of Hong Kong, Hong Kong
2 shared publications - Nan Zhao
School of Electrical Engineering, Beijing Jiaotong University, 47829 Beijing, Beijing China 100044
2 shared publications Trillion Q. Zheng
Institute of Power Electronics and Electric Traction, Beijing Jiaotong University, Beijing, China
1 shared publication- Yu Ai
Institute of Power Electronics and Electric Traction, Beijing Jiaotong University, Beijing, China
1 shared publication
Latest Publications
- 16 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (5) , 4791-4803
Auxiliary Power Supply for Medium-/High-Voltage and High-Power Solid-State Transformers
This paper proposes a new auxiliary power supply (APS), which is used to feed the controllers, drivers, and sensors of the sub-modules for medium-/high-voltage and high-power solid state transformer (SST). In medium-/high-voltage and high-power applications, the APS is usually connected to the dc bus of the sub-module to obtain electric energy. The voltage of the sub-module's dc bus is often as high as several thousand volts, so that the APS must have the ability to handle such high input voltage. An input-series capacitor structure, which makes the voltage stress of the power semiconductor devices reduced, is adopted in the proposed APS. Therefore, the high input voltage can be handled by the low voltage power semiconductor devices. Furthermore, the input voltage sharing (IVS) can be achieved without any special control strategy, which makes the control system simplified and the stability improved. Meanwhile, zero-current switching (ZCS) is guaranteed for all the switches, so that the power density and efficiency can be improved. Finally, the simulation model and prototype are built, by which the feasibility and effectiveness of the proposed APS are verified.
- 16 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (5) , 4791-4803
Auxiliary Power Supply for Medium-/High-Voltage and High-Power Solid-State Transformers
This paper proposes a new auxiliary power supply (APS), which is used to feed the controllers, drivers, and sensors of the sub-modules for medium-/high-voltage and high-power solid state transformer (SST). In medium-/high-voltage and high-power applications, the APS is usually connected to the dc bus of the sub-module to obtain electric energy. The voltage of the sub-module's dc bus is often as high as several thousand volts, so that the APS must have the ability to handle such high input voltage. An input-series capacitor structure, which makes the voltage stress of the power semiconductor devices reduced, is adopted in the proposed APS. Therefore, the high input voltage can be handled by the low voltage power semiconductor devices. Furthermore, the input voltage sharing (IVS) can be achieved without any special control strategy, which makes the control system simplified and the stability improved. Meanwhile, zero-current switching (ZCS) is guaranteed for all the switches, so that the power density and efficiency can be improved. Finally, the simulation model and prototype are built, by which the feasibility and effectiveness of the proposed APS are verified.
- 21 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 34 (9) , 8453-8467
A Power Electronic Traction Transformer Configuration With Low-Voltage IGBTs for Onboard Traction Application
Solid-State transformer for onboard traction application is also addressed as power electronic traction transformer (PETT), which is used to replace the line frequency traction transformer and four-quadrant converter to further improve efficiency, save installation space, and reduce weight of the onboard equipment. However, based on the conventional PETT configuration with the modular series-parallel structure, it is hard to guarantee the high efficiency and high power density at the same time due to the limitations caused by the switching characteristics of the semiconductor devices, transformer design, and high-voltage insulation design. To deal with the mentioned problem, a PETT configuration and the parameters' design method for onboard traction application are proposed in this paper to replace the conventional dc/dc stage with the low-voltage insulated gate bipolar translator (IGBTs). By using the proposed configuration, the high-voltage IGBTs can be replaced by the low-voltage IGBTs, which can help reduce switching loss. Meanwhile, zero-current switching or zero-voltage switching for all the IGBTs can be guaranteed, and the number of the medium-frequency transformers (MFTs) will not increase. Therefore, a multiple optimization of PETT, including switching losses, the number of MFTs and switches, and costs, can be finally achieved. Finally, an experimental prototype is built to verify the performance of the proposed PETT configuration.
- 21 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 34 (9) , 8453-8467
A Power Electronic Traction Transformer Configuration With Low-Voltage IGBTs for Onboard Traction Application
Solid-State transformer for onboard traction application is also addressed as power electronic traction transformer (PETT), which is used to replace the line frequency traction transformer and four-quadrant converter to further improve efficiency, save installation space, and reduce weight of the onboard equipment. However, based on the conventional PETT configuration with the modular series-parallel structure, it is hard to guarantee the high efficiency and high power density at the same time due to the limitations caused by the switching characteristics of the semiconductor devices, transformer design, and high-voltage insulation design. To deal with the mentioned problem, a PETT configuration and the parameters' design method for onboard traction application are proposed in this paper to replace the conventional dc/dc stage with the low-voltage insulated gate bipolar translator (IGBTs). By using the proposed configuration, the high-voltage IGBTs can be replaced by the low-voltage IGBTs, which can help reduce switching loss. Meanwhile, zero-current switching or zero-voltage switching for all the IGBTs can be guaranteed, and the number of the medium-frequency transformers (MFTs) will not increase. Therefore, a multiple optimization of PETT, including switching losses, the number of MFTs and switches, and costs, can be finally achieved. Finally, an experimental prototype is built to verify the performance of the proposed PETT configuration.