TDTendai O. Dembaremba

Tendai O. Dembaremba

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tendai O. Dembaremba has a total of 22 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Understanding and Managing Phase Instability and Aging Reactions of Coalgae Pyrolysis Oils

    by Olwethu Poswayo, Tendai Dembaremba, Adeniyi Ogunlaja, Gary Dugmore, Zenixole Tshentu

    South Africa greatly suffers from the accumulation of waste coal fines due to its heavy reliance on coal mining. The processing of pyrolysis oil ensures the beneficiation of waste coal fines to provide alternative sustainable fuels. However, phase separation and aging reactions affect the stability of the pyrolysis oils negatively, affecting their processing and the product yields and quality. Understanding and managing the stability of Coalgae pyrolysis oil remain gaps to resolving this issue, and as such, systematic time-course monitoring of Coalgae pyrolysis oils was considered. Phase separation by decanting, nitrogen purging to eliminate the oxidative environment, hydrogen purging to investigate a reducing protic environment, and adsorptive treatment to eliminate coordinating species were used to distinguish possible reactions. The rate and extent of aging reactions were reduced by bubbling the separated phases of pyrolysis oil with nitrogen gas, thereby limiting the interphase and autoxidation reactions. Furthermore, a 22.7% reduction in water content and over 9 MPa·s in P2 viscosity were observed. The use of hydrogen in pyrolysis oils resulted in gum formation and increased viscosity via promotion of condensation reactions. FT-IR, GC-MS, and NMR analyses hinted that oxygenates (phenols and carbonyls) play a major role in phase separation and aging of pyrolysis oil. The use of the in-house adsorbent prevented phase separation by removing oxygenates and resulted in a 62.4% decrease in the water content. The study revealed that removing reactive compounds, such as oxygenates, has a greater effect on managing phase separation and aging in coal-based pyrolysis oil, allowing better handling for further processing.

  • Open Access

    Towards improvement of hydroprocessing catalysts - understanding the role of advanced mineral materials in hydroprocessing catalysts

    by Siphumelele Majodina, Olwethu Poswayo, Tendai O. Dembaremba, Zenixole R. Tshentu

    Mineral materials play a pivotal in heterogeneous catalysts as active, support, or promoter components, with the oil refinery industry being one of the biggest beneficiaries. While conventional hydroprocessing catalysts have historically met the industry’s needs, the growing need to accommodate unique feedstocks, meet the increasing demand for environmentally acceptable products, obtain better product specifications, enhance selectivity for reactions to increase ratios for certain product cuts, and use more cost-effective and abundant mineral materials, has recently motivated for fresh considerations in the development of hydroprocessing catalysts. Based on periodic trends, noble metals possess the most desirable qualities, but their relative abundance in the Earth’s crust is too low to meet industry needs. They are costly and highly sensitive to sulfur poisoning. Mo and W lie in the sweet spot, but it is anticipated that they cannot meet the increasing demand. Investigations of electronic interactions of more economical and abundant metals, such as Nb, V, and Fe, with other elements and support materials have yielded a better understanding of synergistic effects that help to access noble metal-like qualities. This work contrasts conventional hydroprocessing catalysts and recently improved catalysts, detailing the chemistry considerations behind the selection of mineral materials used in the catalysts. It also explores how further manipulation of these mineral materials and synthesis approaches is driving toward more desirable properties. The work brings to the attention of the readers the challenges and opportunities for the further improvement of hydroprocessing catalysts to ensure environmental sustainability while meeting the industry’s growing needs.


  • Synthesis, crystal structures and DFT studies of Co(ii) and Zn(ii) coordination polymers of terephthalate and 4,4′-trimethylenedipyridyl ligands for removal of dibenzothiophene from a model fuel oil

    by Adedibu C. Tella, Samson O. Owalude, Olanrewaju A. Ameen, Hadley S. Clayton, Quadrat Yusuph, Tendai O. Dembaremba, Eric C. Hosten, Adeniyi S. Ogunlaja

    The negative environmental and human health challenges posed by sulfur oxides that are released upon combustion of fuel oils containing sulfur necessitate the development of methods for its removal, and hydroprocessing is the conventional technique. However, dibenzothiophene and its substituted derivatives are refractory. As such, the coordination polymers (CPs): [Co(tmdp)4Cl2]n1 and [Zn(tpa)2(tmdp)2·(H2O)2]n2, where tmdp is trimethylenedipyridine and tpa is terephthalic acid, were synthesized for application in adsorptive separation to selectively remove the refractory compounds. Spectroscopy techniques (UV-vis and FT-IR), single crystal XRD, micro-elemental analysis, TGA and SEM were used for characterization. Heat activation of both CPs was carried out to remove lattice solvent molecules before applying them in adsorption. Both CPs, showed good adsorption of dibenzothiophene (DBT) with maximum adsorption capacities of 49 mg g−1 and 44 mg g−1, respectively. The adsorption studies and theoretical studies carried out pointed to physisorption as the mechanism for adsorption of DBT in both CPs with interactions being predominantly dispersion forces between the ligands and DBT.


  • Coordination Polymers and Polymer Nanofibers for Effective Adsorptive Desulfurization

    by Tendai O. Dembaremba, Adeniyi S. Ogunlaja, Zenixole R. Tshentu

    Desulfurization of fuel oils is an essential process employed in petroleum refineries to reduce the sulfur content to levels mandated for environmental protection. Hydrodesulfurization (HDS), which is currently being employed, is limited in treating refractory organosulfur compounds and only reduces the sulfur content in fuels to a range of 200-500 ppmS. In this chapter, several scientific and technological advances reported in the literature for the desulfurization of fuels are reviewed and discussed. Amongst these techniques, oxidative desulfurization (ODS) and adsorptive desulfurization (ADS) are proposed as additional steps to complement HDS in meeting the mandated ultra-low sulfur levels (10 ppmS). In the ODS technique, refractory organosulfur compounds are oxidized to organosulfones, followed by solvent extraction or adsorption of the organosulfones. The chemistry involved in the development and fabrication of sulfur/sulfone responsive adsorbents is also discussed. The use of molecular imprinted polymers (MIPs) and coordination polymers (CPs) for the selective adsorption of organosulfone compounds (in ODS) and/or organosulfur (in ADS) offers various properties such as imprinting effect, hydrogen bonding, π-π interactions, van der Waals forces, π-complexation, and electrostatic interactions. CPs, in particular metal organic frameworks (MOFs), have been reported to possess suitable features to overcome most of these challenges associated with adsorptive ultra-deep desulfurization when design strategies to achieve good selectivity are strictly followed. Matching the sizes of the cavities to the critical dimensions of the sulfur containing compounds (SCCs), using suitable metal centres which allow for coordinative interaction with the SCCs and using linkers with suitable functionality as to enhance specific interaction (dispersion forces) with the SCCs were considered to be pivotal features to prioritize. The prospects for the use of MIPs and CPs for future industrial applications in desulfurization are envisaged.

  • Trimesic acid–Theophylline and Isopthalic acid–Caffeine Cocrystals: Synthesis, Characterization, Solubility, Molecular Docking, and Antimicrobial Activity

    by Olufunso O. Abosede, Allen T. Gordon, Tendai O. Dembaremba, Carolline M.A. Lorentino, Heloísa F. Frota, André L.S. Santos, Eric C. Hosten, Adeniyi S. Ogunlaja


  • Coordination Polymers and Polymer Nanofibers for Effective Adsorptive Desulfurization

    by Tendai O. Dembaremba, Adeniyi S. Ogunlaja, Zenixole R. Tshentu

    Desulfurization of fuel oils is an essential process employed in petroleum refineries to reduce the sulfur content to levels mandated for environmental protection. Hydrodesulfurization (HDS), which is currently being employed, is limited in treating refractory organosulfur compounds and only reduces the sulfur content in fuels to a range of 200-500 ppmS. In this chapter, several scientific and technological advances reported in the literature for the desulfurization of fuels are reviewed and discussed. Amongst these techniques, oxidative desulfurization (ODS) and adsorptive desulfurization (ADS) are proposed as additional steps to complement HDS in meeting the mandated ultra-low sulfur levels (10 ppmS). In the ODS technique, refractory organosulfur compounds are oxidized to organosulfones, followed by solvent extraction or adsorption of the organosulfones. The chemistry involved in the development and fabrication of sulfur/sulfone responsive adsorbents is also discussed. The use of molecular imprinted polymers (MIPs) and coordination polymers (CPs) for the selective adsorption of organosulfone compounds (in ODS) and/or organosulfur (in ADS) offers various properties such as imprinting effect, hydrogen bonding, π-π interactions, van der Waals forces, π-complexation, and electrostatic interactions. CPs, in particular metal organic frameworks (MOFs), have been reported to possess suitable features to overcome most of these challenges associated with adsorptive ultra-deep desulfurization when design strategies to achieve good selectivity are strictly followed. Matching the sizes of the cavities to the critical dimensions of the sulfur containing compounds (SCCs), using suitable metal centres which allow for coordinative interaction with the SCCs and using linkers with suitable functionality as to enhance specific interaction (dispersion forces) with the SCCs were considered to be pivotal features to prioritize. The prospects for the use of MIPs and CPs for future industrial applications in desulfurization are envisaged.