Surya Abhishek Singaraju
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Surya Abhishek Singaraju has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
- Jasmin Aghassi-Hagmann
Institute of Nanotechnology (INT) Karlsruhe Institute of Technology (KIT) Karlsruhe Germany
14 shared publications - Horst Hahn
Institute of Nanotechnology, Karlsruhe Institute of Technology, Karlsruhe, Germany
12 shared publications - Ben Breitung
Institute of Nanotechnology Karlsruhe Institute of Technology (KIT) Kaiserstr. 12 76131 Karlsruhe Germany
10 shared publications - Gabriel Cadilha Marques
Institute of Nanotechnology (INT), Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany
6 shared publications - Leonardo Velasco
Dirección Académica, Universidad Nacional de Colombia, Sede de La Paz, La Paz 202017, Colombia
5 shared publications Jaehoon Jeong
Institute of Nanotechnology (INT) Karlsruhe Institute of Technology (KIT) Eggenstein-Leopoldshafen 76344 Germany
4 shared publications
Latest Publications
- 19 January 2023
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (2)
Synthesis and Characterization of High‐Entropy CrMoNbTaVW Thin Films Using High‐Throughput Methods
- 19 January 2023
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (2)
Synthesis and Characterization of High‐Entropy CrMoNbTaVW Thin Films Using High‐Throughput Methods
- Open Access
- 15 September 2022
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (2)
Synthesis and Characterization of High‐Entropy CrMoNbTaVW Thin Films Using High‐Throughput Methods
High‐entropy alloys (HEAs) or complex concentrated alloys (CCAs) offer a huge research area for new material compositions and potential applications. Since the combination of several elements sometimes leads to unexpected and unpredictable material properties. In addition to the element combinations, the optimization of the element proportions in CCAs and HEAs is also a decisive factor in tailoring desired material properties. However, it is almost impossible to achieve the composition and characterization of CCAs and HEAs with a sufficient number of compositions by conventional experiments. Therefore, an optimized high‐throughput magnetron sputtering synthesis to fabricate a new HEA gradient layer of six elements is presented. With this approach, the compositional space of the HEA system CrMoNbTaVW can be studied in different subsections to determine the influence of the individual elements and their combinations on the structure, morphology, and physical properties (hardness and resistivity). It is found that the Cr‐, Ta‐, and W‐rich phases, which have a grain size of 10–11 nm, exhibit the hardest mechanical properties, whereas V‐, Ta‐, and Cr‐rich compounds exhibit the highest electrical resistivity. The combination of high‐throughput synthesis, automated analysis tools, and automated data interpretation enables rapid and time‐efficient characterization of the novel CrMoNbTaVW gradient film.
- 15 September 2022
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (2)
Open AccessSynthesis and Characterization of High‐Entropy CrMoNbTaVW Thin Films Using High‐Throughput Methods
High‐entropy alloys (HEAs) or complex concentrated alloys (CCAs) offer a huge research area for new material compositions and potential applications. Since the combination of several elements sometimes leads to unexpected and unpredictable material properties. In addition to the element combinations, the optimization of the element proportions in CCAs and HEAs is also a decisive factor in tailoring desired material properties. However, it is almost impossible to achieve the composition and characterization of CCAs and HEAs with a sufficient number of compositions by conventional experiments. Therefore, an optimized high‐throughput magnetron sputtering synthesis to fabricate a new HEA gradient layer of six elements is presented. With this approach, the compositional space of the HEA system CrMoNbTaVW can be studied in different subsections to determine the influence of the individual elements and their combinations on the structure, morphology, and physical properties (hardness and resistivity). It is found that the Cr‐, Ta‐, and W‐rich phases, which have a grain size of 10–11 nm, exhibit the hardest mechanical properties, whereas V‐, Ta‐, and Cr‐rich compounds exhibit the highest electrical resistivity. The combination of high‐throughput synthesis, automated analysis tools, and automated data interpretation enables rapid and time‐efficient characterization of the novel CrMoNbTaVW gradient film.
- Open Access
Artificial Neurons on Flexible Substrates: A Fully Printed Approach for Neuromorphic Sensing
Printed electronic devices have demonstrated their applicability in complex electronic circuits. There is recent progress in the realization of neuromorphic computing systems (NCSs) to implement basic synaptic functions using solution-processed materials. However, a fully printed neuron is yet to be realised. We demonstrate a fully printed artificial neuromorphic circuit on flexible polyimide (PI) substrate. Characteristic features of individual components of the printed system were guided by the software training of the NCS. The printing process employs graphene ink for passive structures and InO as active material to print a two-input artificial neuron on PI. To ensure a small area footprint, the thickness of graphene film is tuned to target a resistance and to obtain conductors or resistors. The sheet resistance of the graphene film annealed at 300 °C can be adjusted between 200 and 500 k depending on the number of printed layers. The fully printed devices withstand a minimum of 2% tensile strain for at least 200 cycles of applied stress without any crack formation. The area usage of the printed two-input neuron is 16.25 mm, with a power consumption of 37.7 mW, a propagation delay of 1 s, and a voltage supply of 2 V, which renders the device a promising candidate for future applications in smart wearable sensors.Open AccessArtificial Neurons on Flexible Substrates: A Fully Printed Approach for Neuromorphic Sensing
Printed electronic devices have demonstrated their applicability in complex electronic circuits. There is recent progress in the realization of neuromorphic computing systems (NCSs) to implement basic synaptic functions using solution-processed materials. However, a fully printed neuron is yet to be realised. We demonstrate a fully printed artificial neuromorphic circuit on flexible polyimide (PI) substrate. Characteristic features of individual components of the printed system were guided by the software training of the NCS. The printing process employs graphene ink for passive structures and InO as active material to print a two-input artificial neuron on PI. To ensure a small area footprint, the thickness of graphene film is tuned to target a resistance and to obtain conductors or resistors. The sheet resistance of the graphene film annealed at 300 °C can be adjusted between 200 and 500 k depending on the number of printed layers. The fully printed devices withstand a minimum of 2% tensile strain for at least 200 cycles of applied stress without any crack formation. The area usage of the printed two-input neuron is 16.25 mm, with a power consumption of 37.7 mW, a propagation delay of 1 s, and a voltage supply of 2 V, which renders the device a promising candidate for future applications in smart wearable sensors. - 13 September 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (11) , 112103
Inkjet-printed bipolar resistive switching device based on Ag/ZnO/Au structure
In this Letter, we report an inkjet-printed resistive switching device based on an Ag/ZnO/Au structure. The device exhibits bipolar resistive switching behavior, a low operation voltage of about 0.7 V, a high on/off ratio of 107, a long retention time exceeding 104 s, and good endurance. The conduction mechanism of the device in low and high resistive states was studied and showed good consistency with the theory of Ohmic and space charge limited conduction mechanisms, respectively.
- 13 September 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (11) , 112103
Inkjet-printed bipolar resistive switching device based on Ag/ZnO/Au structure
In this Letter, we report an inkjet-printed resistive switching device based on an Ag/ZnO/Au structure. The device exhibits bipolar resistive switching behavior, a low operation voltage of about 0.7 V, a high on/off ratio of 107, a long retention time exceeding 104 s, and good endurance. The conduction mechanism of the device in low and high resistive states was studied and showed good consistency with the theory of Ohmic and space charge limited conduction mechanisms, respectively.
- 8 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 42 (6) , 843-846
Low-Frequency Noise Characteristics of Inkjet-Printed Electrolyte-Gated Thin-Film Transistors
Low-frequency noise is a critical characteristic of transistors, but there are only a few experimental works on the noise in printed electronics. In this work, we characterize the low-frequency noise of inkjet-printed electrolyte-gated thin-film transistors (EGTs) with indium-oxide semiconductors. We confirm that the carrier number fluctuation with correlated mobility fluctuation is the dominating noise generation mechanism. Also, we present the benchmark analysis on the noise level of various thin-film technologies. Notably, the extracted value of trap density near the insulator-channel interface is high, indicating an inferior quality of solution-processed and inkjet-printed thin-films. However, because of electrolyte-gating, the large areal gate capacitance compensates the negative effect of the high trap density, effectively reducing the flat-band voltage noise. As a result, the normalized drain current noise is considerably lower than solution-processed transistors and comparable with sputtered inorganic transistors with dielectric gating. This renders the electrolyte-gating approach useful in reducing the noise for printed/solution-based transistors, suitable for low-noise applications.
- 8 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 42 (6) , 843-846
Low-Frequency Noise Characteristics of Inkjet-Printed Electrolyte-Gated Thin-Film Transistors
Low-frequency noise is a critical characteristic of transistors, but there are only a few experimental works on the noise in printed electronics. In this work, we characterize the low-frequency noise of inkjet-printed electrolyte-gated thin-film transistors (EGTs) with indium-oxide semiconductors. We confirm that the carrier number fluctuation with correlated mobility fluctuation is the dominating noise generation mechanism. Also, we present the benchmark analysis on the noise level of various thin-film technologies. Notably, the extracted value of trap density near the insulator-channel interface is high, indicating an inferior quality of solution-processed and inkjet-printed thin-films. However, because of electrolyte-gating, the large areal gate capacitance compensates the negative effect of the high trap density, effectively reducing the flat-band voltage noise. As a result, the normalized drain current noise is considerably lower than solution-processed transistors and comparable with sputtered inorganic transistors with dielectric gating. This renders the electrolyte-gating approach useful in reducing the noise for printed/solution-based transistors, suitable for low-noise applications.
- Open Access
- 7 September 2020
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (9)
Fully Printed Inverters using Metal‐Oxide Semiconductor and Graphene Passives on Flexible Substrates
- 7 September 2020
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (9)
Open AccessFully Printed Inverters using Metal‐Oxide Semiconductor and Graphene Passives on Flexible Substrates
- 10 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (9) , 3828-3833
ALD-Derived, Low-Density Alumina as Solid Electrolyte in Printed Low-Voltage FETs
In this report, we have studied field-effect transistors (FETs) using low-density alumina for electrolytic gating. Device layers have been prepared starting from the structured ITO glasses by printing the In₂O₃ channels, low-temperature atomic layer deposition (ALD) of alumina (Al₂O₃), and printing graphene top gates. The transistor performance could be deliberately changed by alternating the ambient humidity; furthermore, ID,on/ID,off-ratios of up to seven orders of magnitude and threshold voltages between 0.66 and 0.43 V, decreasing with an increasing relative humidity between 40% and 90%, could be achieved. In contrast to the common usage of Al₂O₃ as the dielectric in the FETs, our devices show electrolyte-type gating behavior. This is a result from the formation of protons on the Al₂O₃ surfaces at higher humidities. Due to the very high local capacitances of the Helmholtz double layers at the channel surfaces, the operation voltage can be as low as 1 V. At low humidities (≤30%), the solid electrolyte dries out and the performance breaks down; however, it can fully reversibly be regained upon a humidity increase. Using ALD-derived alumina as solid electrolyte gating material, thus, allows low-voltage operation and provides a chemically stable gating material while maintaining low process temperatures. However, it has proven to be highly humidity-dependent in its performance.
- 10 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (9) , 3828-3833
ALD-Derived, Low-Density Alumina as Solid Electrolyte in Printed Low-Voltage FETs
In this report, we have studied field-effect transistors (FETs) using low-density alumina for electrolytic gating. Device layers have been prepared starting from the structured ITO glasses by printing the In₂O₃ channels, low-temperature atomic layer deposition (ALD) of alumina (Al₂O₃), and printing graphene top gates. The transistor performance could be deliberately changed by alternating the ambient humidity; furthermore, ID,on/ID,off-ratios of up to seven orders of magnitude and threshold voltages between 0.66 and 0.43 V, decreasing with an increasing relative humidity between 40% and 90%, could be achieved. In contrast to the common usage of Al₂O₃ as the dielectric in the FETs, our devices show electrolyte-type gating behavior. This is a result from the formation of protons on the Al₂O₃ surfaces at higher humidities. Due to the very high local capacitances of the Helmholtz double layers at the channel surfaces, the operation voltage can be as low as 1 V. At low humidities (≤30%), the solid electrolyte dries out and the performance breaks down; however, it can fully reversibly be regained upon a humidity increase. Using ALD-derived alumina as solid electrolyte gating material, thus, allows low-voltage operation and provides a chemically stable gating material while maintaining low process temperatures. However, it has proven to be highly humidity-dependent in its performance.
- Open Access
- 29 July 2020
- Published by Wiley in Batteries & Supercaps
- Vol. 3 (8) , 668
Cover Picture: Tailored Silicon/Carbon Compounds for Printed Li–Ion Anodes (Batteries & Supercaps 8/2020)
- 29 July 2020
- Published by Wiley in Batteries & Supercaps
- Vol. 3 (8) , 668
Open AccessCover Picture: Tailored Silicon/Carbon Compounds for Printed Li–Ion Anodes (Batteries & Supercaps 8/2020)
- 29 July 2020
- Published by Wiley in Batteries & Supercaps
- Vol. 3 (8) , 671
Tailored Silicon/Carbon Compounds for Printed Li–Ion Anodes
Invited for this month's cover picture is the group and collaboration partners of Prof. Horst Hahn from the Institute of Nanotechnology (INT) at Karlsruhe Institute of Technology (KIT). The cover picture shows printed silicon anodes coated with carbon for powering of electrolyte‐gated transistors. Read the full text of the Article at 10.1002/batt.202000052.
- 29 July 2020
- Published by Wiley in Batteries & Supercaps
- Vol. 3 (8) , 671
Tailored Silicon/Carbon Compounds for Printed Li–Ion Anodes
Invited for this month's cover picture is the group and collaboration partners of Prof. Horst Hahn from the Institute of Nanotechnology (INT) at Karlsruhe Institute of Technology (KIT). The cover picture shows printed silicon anodes coated with carbon for powering of electrolyte‐gated transistors. Read the full text of the Article at 10.1002/batt.202000052.
- Open Access
- 22 June 2020
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (9)
Fully Printed Inverters using Metal‐Oxide Semiconductor and Graphene Passives on Flexible Substrates
- 22 June 2020
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (9)
Open AccessFully Printed Inverters using Metal‐Oxide Semiconductor and Graphene Passives on Flexible Substrates