BABetul Akkopru-Akgun

Betul Akkopru-Akgun

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Betul Akkopru-Akgun has a total of 60 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Probing the role of 3D intergranular interactions in local subcoercive switching of textured piezoelectric ceramics

    by Reilly J. Knox, Stanislav A. Udovenko, Betul Akkopru-Akgun, Amlan Das, Mark A. Fanton, Susan Trolier-McKinstry, Darren C. Pagan

  • Open Access

    Polarity-Dependent Charge Transport and Resistance Degradation Enabled by Oxygen-Vacancy Gradients in BiFeO 3 Films

    by Sengsavang Aphayvong, Abhyuday Verma, Kae Nakamura, Ali Habib Akhyari, Takeshi Yoshimura, Susan Trolier-McKinstry, Betul Akkopru-Akgun

    The long-term reliability of Mn-doped BiFeO3 thin films remains a key challenge for their implementation in piezoelectric microelectromechanical systems. In this work, the electronic transport mechanisms and DC resistance degradation of (100) Mn-doped BiFeO3 (BFMO) epitaxial films grown on (100) Si substrates by RF magnetron sputtering were systematically investigated. The leakage current characteristics exhibit a strong polarity dependence, originating from a nonuniform distribution of oxygen vacancies across the film thickness. Under field-up bias, where a high concentration of oxygen vacancies is present near the top interface, leakage is dominated by Poole–Frenkel emission from VÖ related traps in the low-field regime and evolves into trap-controlled space-charge-limited conduction at higher fields, with transport controlled by FeFe′ sites. In contrast, under field-down bias, where the VÖ concentration near the bottom interface is comparatively low, transport is Ohmic at low electric fields and transitions to Poole–Frenkel emission at higher fields, with conduction governed primarily by FeFe′ trap levels. The asymmetric VO·· distribution also gives rise to polarity-dependent DC resistance degradation, governed by field-driven VÖ drift and subsequent accumulation at the cathode interface. Since the [VÖ] is initially higher near the top interface, VÖ redistribution proceeds more rapidly, resulting in accelerated degradation kinetics and a reduced lifetime. The extracted VÖ diffusion coefficient for BFMO (∼2.7 × 10–14 cm2 s–1) is approximately an order of magnitude higher than values reported for PZT films, consistent with the comparatively shorter lifetime observed under similar stress conditions. These findings highlight the pivotal role of defect engineering particularly in controlling oxygen vacancy concentration and migration for optimizing the reliability and performance of BiFeO3-based MEMS devices.


  • Open Access

    Probing the Role of 3D Intergranular Interactions in Local Subcoercive Switching of Textured Piezoelectric Ceramics

    by Reilly J. Knox, Stanislav Udovenko, Betul Akkopru Akgun, Amlan Das, Mark A. Fanton, Susan Trolier-McKinstry, Darren Pagan

    The electromechanical responses of individual grains embedded in ferroelectric ceramics are modulated by local boundary conditions imposed by neighboring grains. In this work, in situ far-field high-energy X-ray diffraction microscopy data were collected for a strongly textured manganese-doped lead-magnesium-niobate-lead-zirconate-titanate ceramic manufactured by templated grain growth. Domain variant volume fractions were estimated for hundreds of grains before and after applying a subcoercive electric field and combined with spatial information to correlate local subcoercive switching behavior with grain neighborhood characteristics. Subcoercive switching was associated with the extent to which a grain's as-poled domain state deviates from that of a perfectly-aligned single crystal, likely reflecting contributions from local features that cannot be resolved with this technique (porosity, grain boundary phases, local composition variations). Competition was observed between grain orientation and intergranular interactions, with the former observed to be less important than the latter when grain volumes were considered. Larger misorientations within the tape-casting plane and reduced ferroelastic switching among near-neighbors were associated with reduced subcoercive switching, together implying a coordinated intergranular switching mechanism. Collectively, these findings emphasize the role of intergranular interactions in modulating local electromechanical response, offering insights into factors responsible for deviations in textured ceramic response relative to single crystals.

  • Open Access

    Physics of wurtzite ferroelectrics

    by Hiroki Moriwake, Betul Akkopru-Akgun, Sebastian Calderon, Elizabeth C. Dickey, Prashun Gorai

    Ferroelectricity was long considered incompatible with the wurtzite structure, but the recent discovery of switchable polarization in wurtzite alloys has renewed interest in these materials for integrated electronic and memory applications. The development of wurtzite ferroelectrics faces significant technological challenges, which can be addressed through a fundamental physical understanding of their dielectric and ferroelectric properties. This article focuses on the physics that govern the polarization switching behavior, emphasizing the atomic- and meso-scale (domain) mechanisms involved in the transition between polarization states. A distinguishing feature of this article is a deep dive into the role of intrinsic and extrinsic defects—an area that has received limited attention in prior reviews, but is increasingly recognized as central to polarization switching, coercive fields, leakage, and fatigue. We highlight how defect behavior evolves during processing and electrical cycling, often contributing to long-term degradation. We also introduce powerful first-principles defect calculations, common in semiconductors but not yet widespread in ferroelectrics, as tools to understand and design materials. By integrating recent theoretical and experimental insights, we aim to provide a framework for advancing wurtzite ferroelectrics. Graphical abstract


  • Open Access

    Switching kinetics in ferroelectric zinc magnesium oxide thin films

    by Leonard Jacques, Drew Behrendt, Erdem Ozdemir, Pedram Yousefian, Robert Jackson Spurling, Pannawit Tipsawat, Betul Akkopru-Akgun, Andrew M. Rappe, Jon-Paul Maria, Keisuke Yazawa, et al.


  • Open Access

    Tunable oxygen vacancy diffusion and electronic conduction through strain engineering in PZT films

    by Betul Akkopru-Akgun, Kathleen Coleman, Arash Kazemi, Ke Wang, Shad Roundy, Susan Trolier-McKinstry

    This study elucidates the roles of strain gradients in enhancing both electronic and ionic conductivity of Nb doped lead zirconate titanate (PNZT) films. Increasing the applied strain in bent PNZT films from 0 to 0.5% reduced the energy barrier for vacancy diffusion from 0.75 ± 0.1 to 0.5 ± 0.1 eV, resulting in an increase in mobile [Formula: see text] from 2.1 ± 0.2 × 1018/cm3 to 1.6 ± 0.4 × 1019/cm3. Notably, [Formula: see text] migration was detected even in bent samples not subjected to prior electrical degradation. The enhancement of migration is attributed to the electric field induced by coupled flexoelectric and piezoelectric effects. The increasing population of mobile [Formula: see text] due to bending strain enhances electron trapping by Ti4+ ions, raising the electronic conductivity. Concurrently, hole hopping between Pb2+ and Pb3+ decreases with increasing bending strain, indicating a decline in hole concentration and a shift in the n-p transition to higher [Formula: see text] and temperature ranges. In pristine films on Ni metal foils, increasing the bending strain from 0 to 0.5% increased the volume fraction of a-domains from 15 to 64% due to ferroelastic domain reorientation. Consequently, the reversible Rayleigh coefficient [Formula: see text] rose from 540 ± 6 to 790 ± 8, as the permittivity of a-domains is higher than that of c-domains. Furthermore, ferroelastic domain reorientation increased the concentration of non-180° domain walls, amplifying the irreversible Rayleigh parameter, α from 28 ± 4 to 47 ± 5 cm/kV. In the electrically degraded state, both [Formula: see text]and α decreased, due to (1) loss of switchable units from localized dielectric breakdowns, (2) changes in domain configurations, and (3) the internal bias field. These results will influence the vast majority of piezoelectric microelectromechanical systems which utilize bending to enhance displacements.


  • Open Access

    Wake up and retention in zinc magnesium oxide ferroelectric films

    by Leonard Jacques, Gyunghyun Ryu, Devin Goodling, Saiphaneendra Bachu, Rojin Taheri, Pedram Yousefian, Smitha Shetty, Betul Akkopru-Akgun, Clive Randall, Nasim Alem, et al.

    Zn0.64Mg0.36O (ZMO) is a newly discovered ferroelectric oxide with the wurtzite structure. Epitaxial Zn0.64Mg0.36O films from 0.036 to 0.5 μm in thickness are grown on Pt/sapphire with the crystallographic c-axis out of plane. At room temperature, the remanent polarization is ∼80 μC/cm2 and the coercive field is ∼3 MV/cm. The coercive field is strongly temperature dependent up to 240 °C with a pseudo-activation energy of 23 ± 0.3 meV, suggesting that polarization reversal occurs through an extrinsic process such as domain wall motion. ZMO films can be woken up in 20 electric field cycles on driving near the coercive field; they wake up in a single loop at fields in excess of 4 MV/cm. A thermally activated fluid imprint process, with a pseudo-activation energy of 67 ± 8 meV, enlarges the coercive field by several hundred kV cm−1 after switching the polarization. Additionally, ZMO films exhibit excellent retention characteristics; no reduction in the polarization is observed up to 1000 h from room temperature to 200 °C bakes. This current early generation of ZMO films can survive several thousand switching cycles before dielectric breakdown occurs.


  • Open Access

    Tuning Nb Solubility, Electrical Properties, and Imprint through PbO Stoichiometry in PZT Films

    by Betul Akkopru-Akgun, Susan Trolier-McKinstry

    Lead zirconate titanate (PZT) films with high Nb concentrations (6–13 mol%) were grown by chemical solution deposition. In concentrations up to 8 mol% Nb, the films self-compensate the stoichiometry; single phase films were grown from precursor solutions with 10 mol% PbO excess. Higher Nb concentrations induced multi-phase films unless the amount of excess PbO in the precursor solution was reduced. Phase pure perovskite films were grown with 13 mol% excess Nb with the addition of 6 mol% PbO. Charge compensation was achieved by creating lead vacancies when decreasing excess PbO level; using Kroger-Vink notation, NbTi• are ionically compensated by VPb″ to maintain charge neutrality in heavily Nb-doped PZT films. With Nb doping, films showed suppressed {100} orientation, the Curie temperature decreased, and the maximum in the relative permittivity at the phase transition broadened. The dielectric and piezoelectric properties were dramatically degraded due to increased quantity of the non-polar pyrochlore phase in multi-phase films; εr reduced from 1360 ± 8 to 940 ± 6, and the remanent d33,f value decreased from 112 to 42 pm/V when increasing the Nb concentration from 6 to 13 mol%. Property deterioration was corrected by decreasing the PbO level to 6 mol%; phase pure perovskite films were attained. εr and the remanent d33,f increased to 1330 ± 9 and 106 ± 4 pm/V, respectively. There was no discernable difference in the level of self-imprint in phase pure PZT films with Nb doping. However, the magnitude of the internal field after thermal poling at 150 °C increased significantly; the level of imprint was 30 kV/cm and 11.5 kV/cm in phase pure 6 mol% and 13 mol% Nb-doped films, respectively. The absence of mobile VO••, coupled with the immobile VPb″ in 13 mol% Nb-doped PZT films, leads to lower internal field formation upon thermal poling. For 6 mol% Nb-doped PZT films, the internal field formation was primarily governed by (1) the alignment of (VPb″−VO•• )x and (2) the injection and subsequent electron trapping by Ti4+. For 13 mol% Nb-doped PZT films, hole migration between VPb″ controlled internal field formation upon thermal poling.


  • Effect of Mg-doping and Fe-doping in lead zirconate titanate (PZT) thin films on electrical reliability

    by Dongjoo Koh, Song Won Ko, Jung In Yang, Betul Akkopru-Akgun, Susan Trolier-McKinstry

    Uniformly acceptor doped Pb(Zr0.48Ti0.52)O3 (PZT) films with 2 mol. % Mg or Fe prepared by chemical solution deposition exhibited decreased dielectric constants and remanent polarizations relative to undoped PZT. For highly accelerated lifetime testing (HALT) at 200 °C and an electric field of 300 kV/cm in the field up direction, the HALT lifetimes (t50) for undoped, Mg-doped, and Fe-doped PZT films were shortened from 2.81 ± 0.1 to 0.21 ± 0.1 and 0.54 ± 0.04 h, respectively. Through thermally stimulated depolarization current measurement, significant VO∙∙ electromigration was found in homogeneously Mg-doped PZT thin films, a major factor in their short HALT lifetime. Because the concentration of oxygen vacancies increases with uniform acceptor doping, the lifetime decreases. In contrast, when a thin layer of Mg-doped or Fe-doped PZT was deposited on undoped PZT or Nb-doped PZT (PNZT), the HALT lifetimes were longer than those of pure PZT or PNZT films. This confirms prior work on PNZT films with a Mn-doped top layer, demonstrating that the HALT lifetime increases for composite films when a layer with multivalent acceptors is present near the negative electrode during HALT. In that case, the compensating electrons are trapped, presumably on the multivalent acceptors, thus increasing the lifetime.


  • Links between defect chemistry, conduction, and lifetime in heavily Nb doped lead zirconate titanate films

    by Betul Akkopru-Akgun, Ke Wang, Susan Trolier-McKinstry

    Phase pure PbZr0.52Ti0.48O3 (PZT) films with up to 13 mol. % Nb were prepared on Pt-coated Si substrates using chemical solution deposition; charge compensation for Nb was accomplished by reducing the concentration of lead in the film. For high Nb doping levels, (1) superoxidation of the PZT film surface makes the PZT/Pt interface more p-type and, hence reduces electron injection over the Schottky barrier, (2) the bulk charge transport mechanism changes from electron trapping by Ti4+ to hole migration between lead vacancies, and (3) the ionic conductivity due to migration of oxygen vacancies decreases. For ≤6 mol. % Nb, electrical degradation was controlled via field-induced accumulation of oxygen vacancies near the cathode, which, in turn, leads to Schottky barrier lowering and electron trapping by Ti4+. In phase pure 13 mol. % Nb doped PZT films, on the other hand, the increase in the leakage current during electrical degradation was dominated by hole migration between lead vacancies (2[VPb″]∼[h•]) . A much lower lifetime and drastic increase in the leakage current upon electrical degradation was observed in mixed phase PNZT films, which was attributed to (1) a more electrically conductive pyrochlore phase and (2) a high concentration of lead vacancies.