Kai Cai
Research Subjects
Kai Cai has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Dong Guo
School of Health Science and Engineering, University of Shanghai for Science and Technology, Shanghai 200093, China
25 shared publications Yong Huang
Department of Materials Science & Engineering, Tsinghua University, Beijing 100084, China
9 shared publicationsHe-Sun Zhu
8 shared publicationsLongtu Li
Tsinghua University Department of Materials Science and Engineering, State Key Laboratory of New Ceramics and Fine Processing Beijing 100084, People’s Republic of China
5 shared publicationsYunli Wang
5 shared publicationsZhilun Gui
Tsinghua University Department of Materials Science and Engineering, State Key Laboratory of New Ceramics and Fine Processing Beijing 100084, People’s Republic of China
5 shared publications
Latest Publications
- 10 February 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (10) , 9634-9645
Tailoring the polyvinylidene fluoride phase structure in high permittivity MXene/polyvinylidene fluoride composite films via supercooling of the polymer melt
In this study, we report a distinct phase tailorable solution cast polyvinylidene fluoride (PVDF)‐based composite films with transition metal carbides and nitride (MXene) fillers achieved by supercooling of the PVDF melt and their dielectric energy storage performance. An unusual thermal treatment temperature higher than the widely used Tm was used to realize supercooling. Phase structure analysis by using attenuated total reflection infrared spectroscopy (ATR‐IR), X‐ray diffraction (XRD) and differential scanning calorimetry (DSC) indicated that a small amount of added MXene induced a considerable fraction (76%) of β‐phase PVDF and a 10‐fold increase in dielectric permittivity (100 Hz) due to filler induced crystallization and super confinement effect when a processing temperature around melting temperature (Tm) is used. Surprisingly, although chain packing and crystallization of the macromolecules occur below Tm, a higher processing temperature even induced a double polar (β + γ) phase PVDF as a consequence of supercooling and increased crystallization rate. Interestingly, a nonpolar α phase dominant structure was formed again when the processing temperature was 190°C. These findings indicate that the moderate fast crystallization facilitates the polar phase formation, which may be attributed to their higher intermolecular dipole interaction within the geometry confined by the 2D fillers. The results imply a simple way to tailor PVDF phase structure, offering insights into polymer polymorph formation.Highlights: A phase tailorable PVDF‐based composite film with MXene fillers was fabricated. Phase structure of MXene/PVDF film was analyzed via ATR‐IR, XRD, and DSC. MXene induced an increase in dielectric permittivity and high β‐phase in PVDF. Thermal treatment at various temperatures tailored the phase structure of PVDF.
- 10 February 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (10) , 9634-9645
Tailoring the polyvinylidene fluoride phase structure in high permittivity MXene/polyvinylidene fluoride composite films via supercooling of the polymer melt
In this study, we report a distinct phase tailorable solution cast polyvinylidene fluoride (PVDF)‐based composite films with transition metal carbides and nitride (MXene) fillers achieved by supercooling of the PVDF melt and their dielectric energy storage performance. An unusual thermal treatment temperature higher than the widely used Tm was used to realize supercooling. Phase structure analysis by using attenuated total reflection infrared spectroscopy (ATR‐IR), X‐ray diffraction (XRD) and differential scanning calorimetry (DSC) indicated that a small amount of added MXene induced a considerable fraction (76%) of β‐phase PVDF and a 10‐fold increase in dielectric permittivity (100 Hz) due to filler induced crystallization and super confinement effect when a processing temperature around melting temperature (Tm) is used. Surprisingly, although chain packing and crystallization of the macromolecules occur below Tm, a higher processing temperature even induced a double polar (β + γ) phase PVDF as a consequence of supercooling and increased crystallization rate. Interestingly, a nonpolar α phase dominant structure was formed again when the processing temperature was 190°C. These findings indicate that the moderate fast crystallization facilitates the polar phase formation, which may be attributed to their higher intermolecular dipole interaction within the geometry confined by the 2D fillers. The results imply a simple way to tailor PVDF phase structure, offering insights into polymer polymorph formation.Highlights: A phase tailorable PVDF‐based composite film with MXene fillers was fabricated. Phase structure of MXene/PVDF film was analyzed via ATR‐IR, XRD, and DSC. MXene induced an increase in dielectric permittivity and high β‐phase in PVDF. Thermal treatment at various temperatures tailored the phase structure of PVDF.
- 22 July 2019
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 11 (31) , 14896-14906
Self-assembled full nanowire P(VDF-TrFE) films with both anisotropic and high bidirectional piezoelectricity
With the explosive growth of flexible electronics, the prototype piezoelectric polymer poly(vinylidene fluoride-trifluoroethylene) [P(VDF-TrFE)] has gained tremendous attention due to potential applications in flexible sensors, energy harvesters, and new smart devices. However, full realization of these applications is still challenging due to the lack of high quality films with strong piezoelectricity, which requires tailored molecular organization. Here we report unique ‘full nanowire’ P(VDF-TrFE) films with substantially enhanced bidirectional performance by a simple self-assembly via selective vapor annealing. Structural analysis showed that the solvent molecules significantly enhanced the copolymer chain mobility, giving highly ordered nanowires, whose quantity increased with time and finally formed a full flat-on lamellar nanowire array with backbones highly aligned along the film plane, leading to high lateral piezoelectricity as revealed by vector piezoresponse force microscopy and confirmed by electrical measurements. Surprisingly, the nanowire films also showed a much higher vertical piezoelectric coefficient (−35.2 pC N−1 directly measured by using a Berlincourt meter) than that of usually crystallized films owing to simultaneously enhanced molecular order and dipole switching ability. The scalability of the new method might boost industrial applications, and the findings may provide hints on new routes to nanostructured polymers with novel functionalities and deepen our understanding of the self-assembly of random copolymers.
- 22 July 2019
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 11 (31) , 14896-14906
Self-assembled full nanowire P(VDF-TrFE) films with both anisotropic and high bidirectional piezoelectricity
With the explosive growth of flexible electronics, the prototype piezoelectric polymer poly(vinylidene fluoride-trifluoroethylene) [P(VDF-TrFE)] has gained tremendous attention due to potential applications in flexible sensors, energy harvesters, and new smart devices. However, full realization of these applications is still challenging due to the lack of high quality films with strong piezoelectricity, which requires tailored molecular organization. Here we report unique ‘full nanowire’ P(VDF-TrFE) films with substantially enhanced bidirectional performance by a simple self-assembly via selective vapor annealing. Structural analysis showed that the solvent molecules significantly enhanced the copolymer chain mobility, giving highly ordered nanowires, whose quantity increased with time and finally formed a full flat-on lamellar nanowire array with backbones highly aligned along the film plane, leading to high lateral piezoelectricity as revealed by vector piezoresponse force microscopy and confirmed by electrical measurements. Surprisingly, the nanowire films also showed a much higher vertical piezoelectric coefficient (−35.2 pC N−1 directly measured by using a Berlincourt meter) than that of usually crystallized films owing to simultaneously enhanced molecular order and dipole switching ability. The scalability of the new method might boost industrial applications, and the findings may provide hints on new routes to nanostructured polymers with novel functionalities and deepen our understanding of the self-assembly of random copolymers.
- 5 January 2018
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 6 (6) , 1433-1444
Revealing the real high temperature performance and depolarization characteristics of piezoelectric ceramics by combined in situ techniques
Polarization variation in a thermal cycle and in situ HT d33 revealed real depolarization temperature and distinct d33 recovery.
- 5 January 2018
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 6 (6) , 1433-1444
Revealing the real high temperature performance and depolarization characteristics of piezoelectric ceramics by combined in situ techniques
Polarization variation in a thermal cycle and in situ HT d33 revealed real depolarization temperature and distinct d33 recovery.
- 1 July 2017
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 261, 311-316
Bismuth layered ceramic solid solution with high temperature piezoelectricity endurance and low sintering temperature
- 1 July 2017
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 261, 311-316
Bismuth layered ceramic solid solution with high temperature piezoelectricity endurance and low sintering temperature
- 13 March 2017
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 50 (15) , 155302
Significantly enhanced piezoelectricity in low-temperature sintered Aurivillius-type ceramics with ultrahigh Curie temperature of 800 °C
We report an Aurivillius-type piezoelectric ceramic (Ca 1−2 x (LiCe) x Bi 4 Ti 3.99 Zn 0.01 O 15 ) that has an ultrahigh Curie temperature ( T c ) around 800 °C and a significantly enhanced piezoelectric coefficient ( d 33 ), comparable to that of textured ceramics fabricated using the complicated templating method. Surprisingly, the highest d 33 of 26 pC/N was achieved at an unexpectedly low sintering temperature ( T s ) of only 920 °C (~200 °C lower than usual) despite the non-ideal density. Study of different synthesized samples indicates that a relatively low T s is crucial for suppressing Bi evaporation and abnormal grain growth, which are indispensable for high resistivity and effective poling due to decreased carrier density and restricted anisotropic conduction. Because the layered structure is sensitive to lattice defects, controlled Bi loss is considered to be crucial for maintaining structural order and spontaneous polarization. This low- T s system is very promising for practical applications due to its high piezoelectricity, low cost and high reproducibility. Contrary to our usual understanding, the results reveal that a delicate balance of density, Bi loss and grain morphology achieved by adjusting the sintering temperature is crucial for the enhancing performance in Aurivillius-type high- T c ceramics.
- 13 March 2017
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 50 (15) , 155302
Significantly enhanced piezoelectricity in low-temperature sintered Aurivillius-type ceramics with ultrahigh Curie temperature of 800 °C
We report an Aurivillius-type piezoelectric ceramic (Ca 1−2 x (LiCe) x Bi 4 Ti 3.99 Zn 0.01 O 15 ) that has an ultrahigh Curie temperature ( T c ) around 800 °C and a significantly enhanced piezoelectric coefficient ( d 33 ), comparable to that of textured ceramics fabricated using the complicated templating method. Surprisingly, the highest d 33 of 26 pC/N was achieved at an unexpectedly low sintering temperature ( T s ) of only 920 °C (~200 °C lower than usual) despite the non-ideal density. Study of different synthesized samples indicates that a relatively low T s is crucial for suppressing Bi evaporation and abnormal grain growth, which are indispensable for high resistivity and effective poling due to decreased carrier density and restricted anisotropic conduction. Because the layered structure is sensitive to lattice defects, controlled Bi loss is considered to be crucial for maintaining structural order and spontaneous polarization. This low- T s system is very promising for practical applications due to its high piezoelectricity, low cost and high reproducibility. Contrary to our usual understanding, the results reveal that a delicate balance of density, Bi loss and grain morphology achieved by adjusting the sintering temperature is crucial for the enhancing performance in Aurivillius-type high- T c ceramics.
- 9 January 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 5 (10) , 2531-2541
A distinct mutual phase transition in a new PVDF based lead-free composite film with enhanced dielectric and energy storage performance and low loss
Environment-friendly polyvinylidene fluoride (PVDF) based composite films were fabricated by using a high permittivity lead-free Ba(Sn,Ti)O3–(Ba,Ca)TiO3(BCTS) ceramic filler with a special ‘tricritical’ phase structure.
- 9 January 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 5 (10) , 2531-2541
A distinct mutual phase transition in a new PVDF based lead-free composite film with enhanced dielectric and energy storage performance and low loss
Environment-friendly polyvinylidene fluoride (PVDF) based composite films were fabricated by using a high permittivity lead-free Ba(Sn,Ti)O3–(Ba,Ca)TiO3(BCTS) ceramic filler with a special ‘tricritical’ phase structure.
- 16 June 2016
- Published by Springer Nature in Science China Technological Sciences
- Vol. 59 (7) , 1048-1053
Structural and electrical properties of high Curie temperature Aurivillius phase composite ceramics with largely enhanced piezoelectricity
- 16 June 2016
- Published by Springer Nature in Science China Technological Sciences
- Vol. 59 (7) , 1048-1053
Structural and electrical properties of high Curie temperature Aurivillius phase composite ceramics with largely enhanced piezoelectricity
- 8 July 2015
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 98 (10) , 3165-3172
Enhanced Ferroelectric Phase Stability and High Temperature Piezoelectricity in PN Ceramics via Multisite Co‐Doping
The tungsten bronze‐type lead metaniobate (PbNb2O6, PN) is a promising material for high‐temperature piezoelectric devices, while its application is limited by the difficulty in fabrication. In this study, the microstructure and electrical properties of Ca‐doped PN and Ca, Mn‐co‐doped PN ceramics sintered at different temperatures were investigated. Doping promoted the formation of the originally metastable ferroelectric orthorhombic phase. This might be partly attributed to the increased lattice distortion of the orthorhombic phase in the doped samples compared to that reported for pure PN. However, in single A‐site Ca‐doped PN the ferroelectric orthorhombic structure showed a low stability and started to transform to paraelectric phase far below 300°C, resulting in unstable high temperature piezoelectric properties. Interestingly, such a phase transition was completely depressed by A‐site Ca and multisite Mn‐co‐doping, which also improved the piezoelectric performance (d33 = 71 pC/N) and thermal stability in both structure and piezoelectricity. The better stability and performance of the co‐doped samples were explained by the improved sintering behavior and poling efficiency as well as its ability to occupy different sites in the TTB lattice.
- 8 July 2015
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 98 (10) , 3165-3172
Enhanced Ferroelectric Phase Stability and High Temperature Piezoelectricity in PN Ceramics via Multisite Co‐Doping
The tungsten bronze‐type lead metaniobate (PbNb2O6, PN) is a promising material for high‐temperature piezoelectric devices, while its application is limited by the difficulty in fabrication. In this study, the microstructure and electrical properties of Ca‐doped PN and Ca, Mn‐co‐doped PN ceramics sintered at different temperatures were investigated. Doping promoted the formation of the originally metastable ferroelectric orthorhombic phase. This might be partly attributed to the increased lattice distortion of the orthorhombic phase in the doped samples compared to that reported for pure PN. However, in single A‐site Ca‐doped PN the ferroelectric orthorhombic structure showed a low stability and started to transform to paraelectric phase far below 300°C, resulting in unstable high temperature piezoelectric properties. Interestingly, such a phase transition was completely depressed by A‐site Ca and multisite Mn‐co‐doping, which also improved the piezoelectric performance (d33 = 71 pC/N) and thermal stability in both structure and piezoelectricity. The better stability and performance of the co‐doped samples were explained by the improved sintering behavior and poling efficiency as well as its ability to occupy different sites in the TTB lattice.
- 24 April 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (16) , 164102
Low-cost (0.1BiYbO3-0.9PbTiO3)-PbZrO3-xMn high Curie temperature piezoelectric ceramics with improved high-temperature performance
Here, we report the structure and performance of a low-cost high Curie temperature (TC) Mn-doped ternary BiYbO3-Pb(Zr,Ti)O3 (BY-PZT-xMn) perovskite piezoelectric ceramic system. The partial substitution of Mn for the A-site Pb, B-site Ti and Zr of the ternary system enhanced both the piezoelectric coefficient and the mechanical quality factor, indicating that the variable valence element induced combinatory soft and hard doped characteristics. The improved electrical performance was found to be related to the improved density and homogeneity, and a correlation between the piezoelectricity and the grain size was also observed. More importantly, a Mn doping level of less than 0.8 mol. % also obviously enhanced the thermal stability of the samples, as reflected by the higher TC and depolarization temperature (Td) measured via both in situ Berlincourt method and annealing experiments, and a correlation between TC and tetragonality of BY-PZT-xMn system was observed. The sample with 0.8 mol. % Mn showed a remarkable overall performance with a d33 of 246 pC/N and a TC around 400 °C, which is expected to be promising for high temperature piezoelectric device applications.
- 24 April 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (16) , 164102
Low-cost (0.1BiYbO3-0.9PbTiO3)-PbZrO3-xMn high Curie temperature piezoelectric ceramics with improved high-temperature performance
Here, we report the structure and performance of a low-cost high Curie temperature (TC) Mn-doped ternary BiYbO3-Pb(Zr,Ti)O3 (BY-PZT-xMn) perovskite piezoelectric ceramic system. The partial substitution of Mn for the A-site Pb, B-site Ti and Zr of the ternary system enhanced both the piezoelectric coefficient and the mechanical quality factor, indicating that the variable valence element induced combinatory soft and hard doped characteristics. The improved electrical performance was found to be related to the improved density and homogeneity, and a correlation between the piezoelectricity and the grain size was also observed. More importantly, a Mn doping level of less than 0.8 mol. % also obviously enhanced the thermal stability of the samples, as reflected by the higher TC and depolarization temperature (Td) measured via both in situ Berlincourt method and annealing experiments, and a correlation between TC and tetragonality of BY-PZT-xMn system was observed. The sample with 0.8 mol. % Mn showed a remarkable overall performance with a d33 of 246 pC/N and a TC around 400 °C, which is expected to be promising for high temperature piezoelectric device applications.
- 1 September 2014
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 216, 335-341
Mn doped hard type perovskite high-temperature BYPT–PZN ternary piezoelectric ceramics
- 1 September 2014
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 216, 335-341
Mn doped hard type perovskite high-temperature BYPT–PZN ternary piezoelectric ceramics