Nils Ratsch
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Nils Ratsch has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Stefan Böhm
Universität Kassel
7 shared publications - Morten Voß
Fraunhofer Institute for Manufacturing Technology and Advanced Materials IFAM
6 shared publications - Till Vallée
Fraunhofer IFAM
6 shared publications - Michael Adam
Fraunhofer Institute for Manufacturing Technology and Advanced Materials IFAM
4 shared publications - Jonas Wirries
Fraunhofer Institut fr Fertigungstechnik, und angewandte Materialforschung IFAM,Bremen,Germany
3 shared publications - Marvin Kaufmann
Fraunhofer Institute for Manufacturing Technology and Advanced Materials IFAM, Bremen, Germany
3 shared publications
Latest Publications
- 28 November 2023
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 101 (1) , 356-378
Thermo-accelerated curing of transparent glass-glass bondings through in-situ heat generation in the adhesive joint
- 28 November 2023
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 101 (1) , 356-378
Thermo-accelerated curing of transparent glass-glass bondings through in-situ heat generation in the adhesive joint
- 1 September 2021
- Published by Elsevier in Construction and Building Materials
- Vol. 298
Accelerated curing of glued-in rods: Influence of manufacturing defects
- 1 September 2021
- Published by Elsevier in Construction and Building Materials
- Vol. 298
Accelerated curing of glued-in rods: Influence of manufacturing defects
- 1 November 2020
- Published by Wiley in Bautechnik
- Vol. 97 (S2) , 86-96
Glued-in rods into hardwood at low temperatures
- 1 November 2020
- Published by Wiley in Bautechnik
- Vol. 97 (S2) , 86-96
Glued-in rods into hardwood at low temperatures
- 15 September 2020
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 98 (2) , 105-130
Accelerated curing of glued-in threaded rods by means of inductive heating — part IV: curing under low temperatures
Glued-in rods (GiR) are a successful class of structura bonded joints for timber engineering applications. However, they suffer from two limitations: relatively slow curing processes, and requirements related to minimum temperatures for the bonding process. Both, to some extent, limit their wider application, in particular on site. Inductive heating was investigated as a method to overcome both drawbacks by speeding up the process, and enabling it under low temperatures. To verify that, a series of four commercially available adhesives was used to manufacture GiR with beech LVL and Ø16 threaded rods embedded by 100 mm, which were then cured under a variety of conditions. Firstly, cold-curing according to the prescriptions of the technical data sheets and inductively, both at +23°C; secondly, inductively at +5°C; and thirdly, at – 10°C. Numerical modelling complementing these studies allowed for insights related to temperature distributions and curing progress otherwise inaccessible through purely experimental means. The results of this study clearly show that, if selecting appropriate adhesives, curing of glued-in rods is not only accelerated from several days down to a few minutes, but that the process can also be carried at much lower temperatures than those prescribed by the technical datasheets. Based thereupon, a completely new range of practical applications, in which gluing of rods can potentially be made independent of ambient temperatures on-site, has been unleashed.
- 15 September 2020
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 98 (2) , 105-130
Accelerated curing of glued-in threaded rods by means of inductive heating — part IV: curing under low temperatures
Glued-in rods (GiR) are a successful class of structura bonded joints for timber engineering applications. However, they suffer from two limitations: relatively slow curing processes, and requirements related to minimum temperatures for the bonding process. Both, to some extent, limit their wider application, in particular on site. Inductive heating was investigated as a method to overcome both drawbacks by speeding up the process, and enabling it under low temperatures. To verify that, a series of four commercially available adhesives was used to manufacture GiR with beech LVL and Ø16 threaded rods embedded by 100 mm, which were then cured under a variety of conditions. Firstly, cold-curing according to the prescriptions of the technical data sheets and inductively, both at +23°C; secondly, inductively at +5°C; and thirdly, at – 10°C. Numerical modelling complementing these studies allowed for insights related to temperature distributions and curing progress otherwise inaccessible through purely experimental means. The results of this study clearly show that, if selecting appropriate adhesives, curing of glued-in rods is not only accelerated from several days down to a few minutes, but that the process can also be carried at much lower temperatures than those prescribed by the technical datasheets. Based thereupon, a completely new range of practical applications, in which gluing of rods can potentially be made independent of ambient temperatures on-site, has been unleashed.
- 2 December 2019
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 97 (8) , 705-729
Accelerated curing of glued-in threaded rods by means of inductive heating – Part III: transient curing
Accelerated curing of glued-in rods (GiR) has been demonstrated in recent papers to represent an interesting option to shorten dramatically the process time. It has been shown that once heated up within minutes, GiR require meaningfully longer to cool down; it is posited that the cooling phase significantly contributes to the curing of the adhesive. This hypothesis has been experimentally tested in the study presented herein on GiR consisting of M16-8.8 threaded steel rods bonded into blocks of laminated veneer lumber (LVL) with a cross section of 120 × 120 mm2 considering four different two-component adhesives (one polyurethane, and three epoxies). Accelerated curing was achieved by transient heating regimes, in which temperatures were raised to different peak temperatures, followed by their cooling. Results indicate that, depending upon the adhesive, transient heating has, for some adhesives, the potential to achieve joint capacities comparable to cold-cured reference GiR, but that is not true for, in particular, 2K polyurethanes. Comparisons between experimental data and results obtained through the characterisation of the curing kinetics pointed out the complex relationship between the development of joint strength and that of chemical conversion degrees.
- 2 December 2019
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 97 (8) , 705-729
Accelerated curing of glued-in threaded rods by means of inductive heating – Part III: transient curing
Accelerated curing of glued-in rods (GiR) has been demonstrated in recent papers to represent an interesting option to shorten dramatically the process time. It has been shown that once heated up within minutes, GiR require meaningfully longer to cool down; it is posited that the cooling phase significantly contributes to the curing of the adhesive. This hypothesis has been experimentally tested in the study presented herein on GiR consisting of M16-8.8 threaded steel rods bonded into blocks of laminated veneer lumber (LVL) with a cross section of 120 × 120 mm2 considering four different two-component adhesives (one polyurethane, and three epoxies). Accelerated curing was achieved by transient heating regimes, in which temperatures were raised to different peak temperatures, followed by their cooling. Results indicate that, depending upon the adhesive, transient heating has, for some adhesives, the potential to achieve joint capacities comparable to cold-cured reference GiR, but that is not true for, in particular, 2K polyurethanes. Comparisons between experimental data and results obtained through the characterisation of the curing kinetics pointed out the complex relationship between the development of joint strength and that of chemical conversion degrees.
- 1 November 2019
- Published by Elsevier in Construction and Building Materials
- Vol. 226, 200-211
Influence of imperfections on the load capacity and stiffness of glued-in rod connections
- 1 November 2019
- Published by Elsevier in Construction and Building Materials
- Vol. 226, 200-211
Influence of imperfections on the load capacity and stiffness of glued-in rod connections
- 18 August 2019
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 97 (3) , 225-250
Accelerated curing of glued-in threaded rods by means of inductive heating – Part I: experiments
Adhesive bonding is nowadays an integral part of timber engineering and sets the basis for efficient joint typologies, as well as for most Engineered Wood Products (EWP). Regarding the manufacturing of joints, in particular under on-site conditions, two-component (2K) adhesives, in particular epoxies (EPX) and polyurethanes (PUR), are preferred over one component (1K) adhesives, because of their ability to cure under ambient conditions. If compared to mechanical fastening, however, the relatively slow curing of most 2K-adhesives used in practice remains a serious disadvantage. This paper summarises investigations on induction heating as a way to speed up significantly the curing process of Glued-in Rods (GiR), a joint type used in timber engineering. Firstly, four commercially available adhesives were investigated with regard to their potential for accelerated curing, resulting in the determination of maximum curing temperatures, and heating rates. Based thereupon, a series of large-scale GiR, involving threaded rods and beech Laminated Veneer Lumber (LVL), were manufactured, and inductively cured. The curing time was dramatically shortened from days to 5 min. Resulting joint capacities depended upon the time elapsed since induction. The resulting findings served as a basis for subsequent investigations to be presented in the second part of this series.
- 18 August 2019
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 97 (3) , 225-250
Accelerated curing of glued-in threaded rods by means of inductive heating – Part I: experiments
Adhesive bonding is nowadays an integral part of timber engineering and sets the basis for efficient joint typologies, as well as for most Engineered Wood Products (EWP). Regarding the manufacturing of joints, in particular under on-site conditions, two-component (2K) adhesives, in particular epoxies (EPX) and polyurethanes (PUR), are preferred over one component (1K) adhesives, because of their ability to cure under ambient conditions. If compared to mechanical fastening, however, the relatively slow curing of most 2K-adhesives used in practice remains a serious disadvantage. This paper summarises investigations on induction heating as a way to speed up significantly the curing process of Glued-in Rods (GiR), a joint type used in timber engineering. Firstly, four commercially available adhesives were investigated with regard to their potential for accelerated curing, resulting in the determination of maximum curing temperatures, and heating rates. Based thereupon, a series of large-scale GiR, involving threaded rods and beech Laminated Veneer Lumber (LVL), were manufactured, and inductively cured. The curing time was dramatically shortened from days to 5 min. Resulting joint capacities depended upon the time elapsed since induction. The resulting findings served as a basis for subsequent investigations to be presented in the second part of this series.
- 18 August 2019
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 97 (3) , 251-281
Accelerated curing of glued-in threaded rods by means of inductive heating – part II: modelling
The curing behaviour of inductively heated glued-in rods (GiR) experimentally tested in Part I of this work was further investigated with regard to the kinetics of adhesive curing, and evolution of strength with time. For that, dynamic DSC measurements were performed, and appropriate kinetic models were derived. These investigations were complemented with rheological experiments in which the adhesive were subjected to the same thermal regime as in the inductive heating of the GiR. Curing kinetics of the GiR were then compared to the increase of strength with time. The comparison showed that curing progress, defined by conversion degree, does not result in proportional strength increase. It was then attempted to estimate the influence of potential residual stresses from the induction curing on joint capacity. A relatively simple FE model was thus derived, which considered two different loading cases: a tensile force acting on the rod, and a shrinkage resulting from the induction process. Their superposition allowed for a general description of the fact that joint capacities increased with time elapsed since induction heating. Depending upon the adhesive considered, fair to very good quality of prediction were achieved.
- 18 August 2019
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 97 (3) , 251-281
Accelerated curing of glued-in threaded rods by means of inductive heating – part II: modelling
The curing behaviour of inductively heated glued-in rods (GiR) experimentally tested in Part I of this work was further investigated with regard to the kinetics of adhesive curing, and evolution of strength with time. For that, dynamic DSC measurements were performed, and appropriate kinetic models were derived. These investigations were complemented with rheological experiments in which the adhesive were subjected to the same thermal regime as in the inductive heating of the GiR. Curing kinetics of the GiR were then compared to the increase of strength with time. The comparison showed that curing progress, defined by conversion degree, does not result in proportional strength increase. It was then attempted to estimate the influence of potential residual stresses from the induction curing on joint capacity. A relatively simple FE model was thus derived, which considered two different loading cases: a tensile force acting on the rod, and a shrinkage resulting from the induction process. Their superposition allowed for a general description of the fact that joint capacities increased with time elapsed since induction heating. Depending upon the adhesive considered, fair to very good quality of prediction were achieved.
- 26 September 2018
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 96 (8) , 738-759
Influence of manufacturing methods and imperfections on the load capacity of glued-in rods
Previous research indicated that glued-in rods (GiR), an adhesively bonded joint in which metallic rods are glued into wood blocks, are an efficient method to connect or reinforce structures in timber engineering, and represent a success story for adhesive bonding in civil engineering. In literature, GiR are mostly manufactured under perfect conditions, regarding both surface states and geometry, with outermost care taken to avoid any deviation thereof. However, in reality GiR are typically manufactured by staff that received little to no training, in particular with regard to the peculiarities of adhesive bonding. Thus the very high standards that apply in other industries, as for example aerospace, are hard to achieve. Additional constraints result from the relatively narrow gap in which the adhesive is injected, and the difficulty to monitor its complete and correct filling. For the manufacturing of GiR-connections several different techniques are used, which were mostly validated empirically. The influence of different manufacturing methods and potential defects on joint performance was investigated. Additionally, this paper sheds additional light on the influence of different typical defects on the load capacity of GiR with steel rods. Several defects, such as corrosion, contamination by oil, dust, wood chips, sand and moisture were considered, and performance of joints manufactured thereof compared to joints without such defects. The results of the research demonstrate that defects on GiR result in a non-negligible reduction of the load capacity, but that this effect is somewhat smaller than expected. Accordingly, GiR connections might be considered as relatively robust with regard to manufacturing.
- 26 September 2018
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 96 (8) , 738-759
Influence of manufacturing methods and imperfections on the load capacity of glued-in rods
Previous research indicated that glued-in rods (GiR), an adhesively bonded joint in which metallic rods are glued into wood blocks, are an efficient method to connect or reinforce structures in timber engineering, and represent a success story for adhesive bonding in civil engineering. In literature, GiR are mostly manufactured under perfect conditions, regarding both surface states and geometry, with outermost care taken to avoid any deviation thereof. However, in reality GiR are typically manufactured by staff that received little to no training, in particular with regard to the peculiarities of adhesive bonding. Thus the very high standards that apply in other industries, as for example aerospace, are hard to achieve. Additional constraints result from the relatively narrow gap in which the adhesive is injected, and the difficulty to monitor its complete and correct filling. For the manufacturing of GiR-connections several different techniques are used, which were mostly validated empirically. The influence of different manufacturing methods and potential defects on joint performance was investigated. Additionally, this paper sheds additional light on the influence of different typical defects on the load capacity of GiR with steel rods. Several defects, such as corrosion, contamination by oil, dust, wood chips, sand and moisture were considered, and performance of joints manufactured thereof compared to joints without such defects. The results of the research demonstrate that defects on GiR result in a non-negligible reduction of the load capacity, but that this effect is somewhat smaller than expected. Accordingly, GiR connections might be considered as relatively robust with regard to manufacturing.