Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ning Cui has a total of 46 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Single-phase Formation Process and Carbon Vacancy Regulation of (TiVNbMoW)Cx High-entropy Ceramics

    by Ning Cui, Yuxin Zhang, Lujie Wang, Tongyang Li, Yuan Yu, Huaguo Tang, Zhuhui Qiao


  • Open Access

    Effects of Medium and Flow Rate on the Film-Forming Structures of B10 Cu-Ni Alloys and Their Resistance to Corrosion Caused by Sulfate-Reducing Bacteria

    by Bochao Lu, Ning Cui, Yimeng Zhang, Ding Guo, Yanan Wang, Xiaopeng Wang, Jizhou Duan

    The effects of medium and flow rate on the film-forming structures of B10 Cu-Ni alloys and their resistance to corrosion caused by sulfate-reducing bacteria are investigated in this article. Combined with a predicted cloud map of pipeline corrosion area and a particle motion trajectory map obtained using Computational Fluid Dynamics (CFD), the growth law of alloy passivation films was analyzed and the pitting process of sulfate-reducing bacteria (SRB) on passivation films was revealed. The results show that the film formation effect is best when the stream of water in the film-forming environment is filtered seawater with a flow rate of 0.8 m/s, which consists of a uniform and dense gray-brown passivated film layer with the strongest resistance to SRB corrosion. When the flow rate is 0 m/s, the clay particles in the seawater cover the surface of the passivation film, hindering the contact of oxygen with the substrate and inhibiting the growth of the passivation film. When the stream of water in the film-forming environment is seawater with a flow rate of 3 m/s, the surface of the substrate shows obvious scouring marks, which is favorable for the enrichment of SRB and further accelerates the pitting corrosion of the substrate. Cl− has a significant influence on the formation of passivation films on B10 Cu-Ni alloys. When the filming medium is deionized water, the B10 Cu-Ni alloy does not form a complete passivation film at all flow rates.


  • Open Access

    Enhancing Passivation Behaviors and Wear Resistance of Biomedical Ti-15Mo Alloy via {332} Twinning Pre-Tension and Aging

    by Shanshan Zhang, Fazhan Yang, Wei Sun, Ning Cui, Tiewei Xu

    The purpose of this investigation was to determine the extent to which a combination of pre-deformation and aging procedures could enhance the corrosion and wear resistance of the Ti-15Mo alloy for biomedical materials. The initial grains were refined with {332} twins and other defects after the pre-deformation, increasing the amount of precipitation nucleation and forming finer α phases during aging. The finer precipitates with numerous boundaries are beneficial in forming a thicker passivation film in phosphate-buffered saline (PBS) solution, and the corrosion resistance of the 20% pre-deform plus aged alloy is improved by 4.23 times. The result indicates that the corrosion passivation behavior and film structure of the biomedical Ti-15Mo alloy are significantly influenced by its microstructure. The worn track and debris of the alloy after pre-tension and aging gradually decreases with the increase in pre-deformation rates, caused by the increase in the hardness and wear resistance. The mechanism of corrosion and wear resistance in PBS solution were revealed, which showed the pre-tension and aging processes that were performed on the Ti-15Mo alloy. This study proposes that pre-tension with {332} twins contributed to precipitation refinement, which would enhance the passivation behaviors and wear resistance of the biomedical β titanium alloy.


  • Open Access

    How Often Should Microbial Contamination Be Detected in Aircraft Fuel Systems? An Experimental Test of Aluminum Alloy Corrosion Induced by Sulfate-Reducing Bacteria

    by Bochao Lu, Yimeng Zhang, Ding Guo, Yan Li, Ruiyong Zhang, Ning Cui, Jizhou Duan

    Microbial contamination in aircraft fuel-containing systems poses significant threats to flight safety and operational integrity as a result of microbiologically influenced corrosion (MIC). Regular monitoring for microbial contamination in these fuel systems is essential for mitigating MIC risks. However, the frequency of monitoring remains a challenge due to the complex environmental conditions encountered in fuel systems. To investigate the impact of environmental variables such as water content, oxygen levels, and temperature on the MIC of aluminum alloy in aircraft fuel systems, orthogonal experiments with various combinations of these variables were conducted in the presence of sulfate-reducing bacteria. Among these variables, water content in the fuel oil demonstrated the most substantial influence on the corrosion rate of aluminum alloys, surpassing the effects of oxygen and temperature. Notably, the corrosion rate of aluminum alloys was the highest in an environment characterized by a 1:1 water/oil ratio, 0% oxygen, and a temperature of 35 °C. Within this challenging environment, conducive to accelerated corrosion, changes in the corrosion behavior of aluminum alloys over time were analyzed to identify the time point at which MIC intensified. Observations revealed a marked increase in the depth and width of corrosion pits, as well as in the corrosion weight-loss rate, starting from the 7th day. These findings offer valuable insights for determining the optimal frequency of microbial contamination detection in aircraft fuel systems.


  • Open Access

    The {332} Twinning Behavior of a Ti-15Mo Medical Alloy during Cyclic Deformation and Its Effect on Microstructure and Performance

    by Tiewei Xu, Bingqing Sun, Shanshan Zhang, Yuancai Liu, Wei Sun, Ning Cui, Binjiang Lv

    In this study, the microstructural evolution of a Ti-15Mo medical alloy was investigated, when the in situ cyclic tensile strain had 2% amplitude and the tension–compression cyclic deformation had 1%, 2%, and 3% amplitude. The Vickers hardness and wear resistance of the alloy were also optimized due to the grain-refining effect after cyclic deformation and annealing. The twinning-induced plasticity (TWIP) was considered the main deformation mechanism of the Ti-15Mo alloy during the tensile–compressive cycle deformation with suitable strain amplitude. The {332} twins and boundaries were the main contributors to the grain refinement. The optimal microstructure, hardness, and wear resistance were obtained in the alloy deformed by tension–compression cyclic strain with a 3% strain amplitude. The wear resistance of the annealed alloy in Hank’s solution was excellent in contrast to the original Ti-15Mo alloy due to its reasonable microstructure and hardness. It is clear that abundant twins were formed and retained in the coarse grains of the original alloy after cyclic deformation and annealing, which provided the expected refined grains and performance.


  • Open Access

    Effect of Heat Treatment on the Microstructure and Mechanical Properties of a Ti-TiAl Laminate Composite

    by Wei Sun, Ning Cui, Yongjun Su, Shuling Zhang, Tiewei Xu, Xiaopeng Wang, Fantao Kong

    The effect of an innovative two-step heat-treatment process on the microstructure and mechanical properties of a Ti-TiAl laminate composite fabricated by hot-pack rolling was studied in this paper. After heat treatment, the fracture toughness of the composite was enhanced and the elongation of the composite was almost twice that of the initial one. These changes were due to the dislocations and substructures stored in the Ti-43Al-9V alloy being decreased, the microstructure of the DsTi700 alloy turning to a duplex structure, the acicular α2 phase being precipitated at the interfacial region and the residual stresses stored in interfacial region being eliminated. The precipitation of dual-scale silicides was the main reason for the slightly reduced strength. Compared with the initial composite, the tensile strength of the heat-treated composite at 25° and 700° only reduced by 2.7% and 4%, respectively. The primary annealing temperature had a huge impact on the mechanical properties of the composite. However, with the change in secondary annealing temperature, the mechanical properties of the composite were not changed significantly. After heat treatment at 940–960 °C/2 h/AC + 725–750 °C/6 h/AC, the composite might possess high, comprehensive mechanical properties.


  • Open Access

    The Microstructure, Mechanical Properties, and Corrosion Resistance of a Novel Extruded Titanium Alloy

    by Ning Cui, Saihao Chen, Tiewei Xu, Wei Sun, Binjiang Lv, Shuling Zhang, Hongzhi Niu, Fantao Kong

    Titanium alloys are widely used in marine engineering and other industries. To broaden their application, a novel (α + β) titanium alloy Ti−6Al−3Mo−2Zr−2Fe was studied in this work. A tube with an outer diameter of 60mm, inner diameter of 38 mm, and length of 500 mm was produced by ingot metallurgy and hot extrusion. The microstructure, mechanical properties, and corrosion resistance of the tube were systematically analyzed. The as−extruded Ti−6Al−3Mo−2Zr−2Fe alloy exhibited a typical duplex microstructure. EBSD observation showed that a strong <10 1¯0>//RD fiber texture of an α phase with a close−packed hexagonal structure was formed in the radial direction. The transformation temperature Tβ was determined to be 880–890 °C. A duplex microstructure with fine α platelets was obtained when the alloy was solution−treated at 850 °C for 1 h and underwent an aging treatment at 550 °C for 6 h. The room−temperature tensile strength and elongation of the aged alloy reached 1081.5 MPa and 6.5%, respectively. The corrosion resistance was tested by open circuit potential and a potentiodynamic polarization curve. The results show that the corrosion resistance of the Ti−6Al−3Mo−2Zr−2Fe alloy was better than that of the commonly used TC4 alloy in both a 3.5% NaCl solution and an acidic solution.


  • Open Access

    Effect of Pyrolysis Conditions on the Performance of Co–Doped MOF–Derived Carbon Catalysts for Oxygen Reduction Reaction

    by Ning Cui, Kexiao Bi, Wei Sun, Qianqian Wu, Yinan Li, Tiewei Xu, Binjiang Lv, Shuling Zhang

    MOF–derived porous carbon is a type of promising catalyst to replace expensive Pt–based catalysts for oxygen reduction reaction (ORR). The catalytic activity for ORR depends closely on pyrolysis conditions. In this work, a Co–doped ZIF–8 material was chosen as a research object. The effect of pyrolysis conditions (temperature, heating rate, two–step heating) on the ORR performance of ZIF–derived carbon catalysts was systematically studied. The Co–ZIF–8 catalyst carbonized at 900 °C exhibits better ORR catalytic activity than that carbonized at 800 °C and 1000 °C. Moreover, a low heating rate can enhance catalytic activity. Two–step pyrolysis is proven to be an effective way to improve the performance of catalysts. Reducing the heating rate in the low–temperature stage is more beneficial to the ORR performance, compared to the heating rate in the high–temperature stage. The results show that the Co–ZIF–8 catalyst exhibits the best performance when the precursor was heated to 350 °C at 2 °C/min, and then heated to 900 °C at 5 °C/min. The optimum Co–ZIF–8 catalyst shows a half–wave potential of 0.82 V and a current density of 5.2 mA·cm−2 in 0.1 M KOH solution. It also exhibits high content of defects and good graphitization. TEM mapping shows that Co and N atoms are highly dispersed in the polyhedral carbon skeleton. However, two–step pyrolysis has no significant effect on the stability of the catalyst.


  • Open Access

    Deformation and Phase Transformation of Disordered α Phase in the (α + γ) Two-Phase Region of a High-Nb TiAl Alloy

    by Haitao Zhou, Fantao Kong, Yanbo Wang, Xiangwu Hou, Ning Cui, Jingli Sun

    In this paper, the deformation and phase transformation of disordered α phase in the (α + γ) two-phase region in as-forged Ti-44Al-8Nb-(W, B, Y) alloy were investigated by hot-compression and hot-packed rolling. The detailed microstructural evolution demonstrated that the deformed microstructure was significantly affected by the deformation conditions, and the microstructure differences were mainly due to the use of a lower temperature and strain rate. Finer α grains were formed by the continuous dynamic recrystallization of α lamellae and α grains distributed around lamellar colonies. Moreover, the grooved γ grains formed by the phase transformation from α lamellae during hot rolling cooperated with and decomposed α lamellae. A microstructure evolution model was built for the TiAl alloy at 1250 °C during hot rolling.


  • Open Access

    Microstructural Characterization and Crack Propagation Behavior of a Novel β-Solidifying TiAl Alloy

    by Shuling Zhang, Ning Cui, Wei Sun, Qiucheng Li

    Novel β-solidifying TiAl alloys have great potential for engineering applications in the aerospace and automotive industries. The introduction of the β0 phase will inevitably affect crack propagation. However, the related mechanism is unclear. In this study, the crack propagation behavior of different β0-containing microstructures was systematically investigated by three-point bending tests. The results show that the coarse γ/α2 lamellar microstructure exhibits better fracture toughness than the fine-grain microstructure because large numbers of γ/α2 lamellar boundaries can effectively hinder crack propagation. The propagation direction depends largely on the orientation of the γ/α2 lamellae. When the angle between the crack propagation direction and the γ/α2 lamellar boundary is small, the crack tends to propagate along γ/α2 lamellae. When the angle is close to 90°, the crack generally propagates by the trans-lamellar mode. Moreover, the crack tends to traverse across the fine β0/γ duplex region due to the low resistance of fine grains in the crack propagation. The transgranular and intergranular modes are the main fracture mechanisms in the microstructure of the fine β0/γ grains. Some shear ligaments can also be identified in the lamellar microstructure and these can consume propagation energy. The enlarged image shows that the crack propagation direction can be changed by the β0 phase, owing to its high hardness. The crack tends to stop at the β0 phase region.