Foroogh Dastoorian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Foroogh Dastoorian has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Maryam Ghorbani
Sari Agricultural Sciences and Natural Resources University, Dep. of Wood and Cellulosic Products Engineering
2 shared publicationsSayed Mohammad Hossein Yahyaee
Sari Agricultural Sciences and Natural Resources University, Dep. of Wood and Cellulosic Products Engineering
2 shared publicationsSeyed Majid Zabihzadeh
Sari Agricultural Sciences and Natural Resources University, Dep. of Wood and Cellulosic Products Engineering
2 shared publicationsFahimeh Hoseinzadeh
1 shared publicationGhanbar Ebrahimi
Department of Wood and Paper Science and Technology Faculty of Natural Resources, University of Tehran P.O. Box 31585-3314, Karaj, Iran
1 shared publication- Mehdi Tajvidi
University of Maine
1 shared publication
Latest Publications
- 1 August 2024
- Published by BioResources in BioResources
- Vol. 19 (4) , 9169-9190
Effect of delignification pretreatment and furfurylation on practical properties of alder wood (Alnus spp.)
Partial delignification of alder wood specimens was performed with alkaline sulfite and peracetic acid (PAA) methods, and subsequently the delignified samples were saturated with furfuryl alcohol, as an eco-friendly chemical. The aim of delignification before furfurylation was to facilitate the penetration of furfuryl alcohol into the cell wall, in order to overcome the weak mechanical properties and hydrophilicity of alder wood as a fast growing species. The results showed that alkaline delignification removed a lower percentage of lignin despite more significant mass loss as compared to peracetic acid delignification method, which indicates more carbohydrates degradation in alkaline delignification. Infrared spectroscopy also confirmed more retention of carbohydrates in the sample delignified with peracetic acid. The polymerization of furfuryl alcohol in the cell cavities decreased the access of water molecules to the hydroxyl groups of the cell wall, increased the contact angle, and decreasing surface wettability. This effect was more noticeable in the PAA-delignified samples. Mechanical tests revealed that the delignified samples with peracetic acid had higher mechanical strength and modulus, compared to the alkaline sulfite delignified samples. This was attributable to the maintenance of carbohydrates during the delignification process.
- 1 August 2024
- Published by BioResources in BioResources
- Vol. 19 (4) , 9169-9190
Effect of delignification pretreatment and furfurylation on practical properties of alder wood (Alnus spp.)
Partial delignification of alder wood specimens was performed with alkaline sulfite and peracetic acid (PAA) methods, and subsequently the delignified samples were saturated with furfuryl alcohol, as an eco-friendly chemical. The aim of delignification before furfurylation was to facilitate the penetration of furfuryl alcohol into the cell wall, in order to overcome the weak mechanical properties and hydrophilicity of alder wood as a fast growing species. The results showed that alkaline delignification removed a lower percentage of lignin despite more significant mass loss as compared to peracetic acid delignification method, which indicates more carbohydrates degradation in alkaline delignification. Infrared spectroscopy also confirmed more retention of carbohydrates in the sample delignified with peracetic acid. The polymerization of furfuryl alcohol in the cell cavities decreased the access of water molecules to the hydroxyl groups of the cell wall, increased the contact angle, and decreasing surface wettability. This effect was more noticeable in the PAA-delignified samples. Mechanical tests revealed that the delignified samples with peracetic acid had higher mechanical strength and modulus, compared to the alkaline sulfite delignified samples. This was attributable to the maintenance of carbohydrates during the delignification process.
- 18 October 2021
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 80 (2) , 367-375
Combined effect of organosolv delignification/polymerization on the set recovery of densified poplar wood
- 18 October 2021
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 80 (2) , 367-375
Combined effect of organosolv delignification/polymerization on the set recovery of densified poplar wood
- 1 November 2019
- Published by Elsevier in Construction and Building Materials
- Vol. 226, 220-226
Creep behavior of heat treated beech wood and the relation to its chemical structure
- 1 November 2019
- Published by Elsevier in Construction and Building Materials
- Vol. 226, 220-226
Creep behavior of heat treated beech wood and the relation to its chemical structure
- 20 November 2008
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 29 (1) , 132-143
Evaluation of Time Dependent Behavior of a Wood Flour/High Density Polyethylene Composite
Short-term flexural creep and stress relaxation tests were conducted on a wood plastic composite containing 30% high density polyethylene (HDPE), 67% fir wood flour, 2% compatibilizer (MAPE), and 1% lubricant. In creep tests, applied stress levels ranged from 30 to 60% of measured flexural strength. The principle of time—stress superposition was applied to form a master curve extending for a maximum of 4 years. The horizontal shift factors conformed to an Arrhenius type equation. Stress relaxation tests were also carried out at strain levels ranging from 30 to 60% of the ultimate strain. The principle of time—strain superposition was applied to form a stress relaxation master curve that extended for 67 days. The horizontal shift factors also conformed to an Arrhenius type equation. The resulting master curves were compared with extrapolated creep and stress relaxation models. To determine whether time—stress superposition is valid for the studied composite material, creep shift factors were applied to stress relaxation data and vice versa. In both creep and stress relaxation tests, it was found that the application of superposition was verified. The results indicated that the studied composite material was rheologically simple, and a single horizontal shifting on time axis was adequate to predict the long term performance of the material.
- 20 November 2008
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 29 (1) , 132-143
Evaluation of Time Dependent Behavior of a Wood Flour/High Density Polyethylene Composite
Short-term flexural creep and stress relaxation tests were conducted on a wood plastic composite containing 30% high density polyethylene (HDPE), 67% fir wood flour, 2% compatibilizer (MAPE), and 1% lubricant. In creep tests, applied stress levels ranged from 30 to 60% of measured flexural strength. The principle of time—stress superposition was applied to form a master curve extending for a maximum of 4 years. The horizontal shift factors conformed to an Arrhenius type equation. Stress relaxation tests were also carried out at strain levels ranging from 30 to 60% of the ultimate strain. The principle of time—strain superposition was applied to form a stress relaxation master curve that extended for 67 days. The horizontal shift factors also conformed to an Arrhenius type equation. The resulting master curves were compared with extrapolated creep and stress relaxation models. To determine whether time—stress superposition is valid for the studied composite material, creep shift factors were applied to stress relaxation data and vice versa. In both creep and stress relaxation tests, it was found that the application of superposition was verified. The results indicated that the studied composite material was rheologically simple, and a single horizontal shifting on time axis was adequate to predict the long term performance of the material.