VCVitalij Chukhlib

Vitalij Chukhlib

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Vitalij Chukhlib has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A comparative analysis of stamping technologies for straight- and curved-axis components of rail transport rolling stock

    by S. V. Biriukov, V. L. Chukhlib

    This paper examines the manufacturing technology for straight- and curved-axis forgings used in the gearbox suspension system of domestic metro traction rolling stock. Emphasis is placed on the specific considerations involved in selecting blank dies for different types of forgings and the need to use them for subsequent blank forming, which will have a positive impact on the quality of the finished product and its stress-strain state following the manufacturing processes. This will be of key importance in the manufacture of forgings for rail transport, as the safety of operations and the quality of passenger service depend on the reliability of the running gear components. The paper also examines the similarities in the general designs of the running gear of urban rail rolling stock, using the examples of suburban electric trains, metro carriages and domestically produced low-floor trams. It identifies the main components characteristic of their bogie designs and draws attention to the location of the traction equipment and its mounting to the bogie frame, taking into account the type of rolling stock and its operating conditions. This article provides a detailed overview of the suspension design for metro carriage gearboxes and highlights the significant number of its component parts manufactured using hot volume forging technology. This underscores the relevance of researching forging processes as a fundamental technology that enables large-scale production of forgings for transport infrastructure requirements. Attention is drawn to the loads borne by the gearbox mounting assembly and its suspension under conditions of significant alternating forces arising during the operation of the traction transmission and the movement of the bogie over irregularities in the track. All these aspects impose stringent requirements on the strength and reliability of these components. The paper also highlights the advantages of using hot volume forging, namely its high productivity and the ability to produce components with enhanced operational characteristics, which will undoubtedly improve the reliability and durability of the forgings manufactured.

  • Open Access

    AKHMEDOV A., CHUKHLIB V., HUBSKYI S., BIBA M. STUDY OF THE INFLUENCE OF THE FORGING REGIME DURING ROLLING ON A MANDREL ON THE QUALITY OF FORGINGS

    by Artem Akhmedov, Vitalij Chukhlib, Serhii Hubskyi, Mykola Biba

    The paper considers the influence of technological parameters of the rolling process on a mandrel on the quality of forgings. The main factors determining the uniformity of plastic deformation, stress-strain state, and temperature distribution in the blank are analyzed. The method of predicting unevenness and the results of computer modeling in the QForm software package are used. The optimal process modes that ensure the uniformity of the structure and improve the mechanical properties of the products are established. It is shown that optimization of parameters allows reducing the number of defects, improving the accuracy of geometry, and reducing the level of production waste.

  • Open Access

    RESEARCH ON THE INFLUENCE OF FORGING DRAWING SCHEMES ON THE UNUNIFOR MIT Y OF DEFORMATION IN FREE FORGING

    by Volodymyr Dolia, Vitalij Chukhlib, Oleksandr Bobrov, Olha Taran

    The paper investigates the influence of different forging drawing schemes ‘passes’ and ‘screw’ on the unevenness of free forging process indicators. The modelling was performed in the QForm s oftware package . The patterns of influence of the deformed state of the forging on the uniformity of plastic flow were analysed. The results showed that the use of the screw drawing scheme contributes to a reduction in the unevenness of deformations and animprovement in th e quality of forgings due to a more uniform redistribution of metal.

  • Open Access

    Development of the technology for manufacturing the bracket for mounting the reducer of the metropolitane cars

    by S. V. Biriukov, V. L. Chukhlib

    This article discusses the developed technology for manufacturing a gearbox mounting bracket used on rolling stock in domestic metro systems. The article also analyses the design of this bracket and the malfunctions that may occur during operation. The specific nature of metro rolling stock operation, characterised by high traffic intensity, frequent acceleration and braking cycles, and significant dynamic loads, places increased demands on the reliability of each structural element of its running gear. Since a significant part of the bogie parts are manufactured using metal pressure processing methods, the issue of improving the quality of stamped forgings becomes a relevant technical task that affects the safety of passenger transport and the accident-free operation of vehicles. This article analyses other works related to improving the mechanical characteristics of products and increasing their quality, which depend on the parameters and methods of their production. The traditional forging technology discussed above usually involves a multi-stage process that includes the use of rolling grooves for preliminary distribution of metal along the axis of the blank. However, this approach increases the size of the stamping equipment and requires more passes, which leads to higher energy costs and production costs. The authors proposed abandoning the use of a rolling groove, since it is possible to manufacture this forging without changing the geometry of the blank before bending. The results of this work can be used by technologists and engineers in the machine-building industry as one of the promising ways to improve and rationalise the stamping of forgings with similar geometry, since by reducing the number of stamping passes, it is possible to reduce the cost of production and manufacture of dies without significantly affecting the stress-strain state of the resulting forging. The expediency of using computer modelling in the design of production technology is also indicated, as it allows all stages of production to be investigated without significant financial costs and ways to improve and rationalise technological operations to be identified, which will have an impact on improving the quality of manufactured products in the future.

  • Open Access

    ANALYSIS AND RESEARCH OF HOOK FORGING TECHNOLOGY

    by Vitalii Chukhlib, Kolisnyk Kostiantyn

    The paper analyses the technology of forging heavy-duty hooks. The forging operations for the manufacture of hooks and the combination of deposition and drawing operations are considered, and the quality of hook forging is examined. Based on the analysis, the basic requirements for the quality of hook forging were formed. The modelling of the deposition process with sequential drawing of the forged hook billet was carried out, as well as the modelling of the drawing process without deposition of the billet and their impact on the deformed state and strain distribution across the billet cross-section. The analysis of the strain distribution across the billet cross-section was made by predicting the unevenness of metal deformation during deposition and drawing, as well as only during drawing without deposition of the billet. In two cases, the index of unevenness of deformation of the workpieces in cross-section during drawing was calculated and graphs of unevenness of deformation were constructed, which showed a more appropriate use of sequential drawing and drawing, which provide an increase in the quality of the forged hook.

  • Open Access

    COMPARATIVE ANALYSIS OF THE SHAPE CHANGE WHEN A PRODUCT IS PRODUCED BY FREE-FORM BENDING

    by Vitalii Chukhlib, Wolfram Volk, Philipp Lechner, Scandola Lorenzo, Serhii Hubskyi, Mykola Biba, Joél Schukraft

    The paper presents a comparative analysis of the shape change of a rod when it is deformed in a moving die using the Abaqus and Qform software packages. The approaches to determining the shape of a profile formed by a moving die are analyzed. Methods for analyzing the shape change when a product is obtained by free-form bending, based on predicting the volumetric unevenness of metal deformation in the processes of pressure treatment and determining the product curvature, are considered. For the process of modeling the bending of a product in a moving die, a rod was selected, as well as an algorithm for moving the moving die and feeding the rod. As a result of the simulation, it was found that the resulting product models in these software systems are identical in geometry. Based on the methods of analyzing the shape change when a product is obtained by free-form bending, we analyzed the uneven distribution of deformation parameters and determined the curvature of the workpiece during deformation. It was found that a significant deformation irregularity is observed in the workpiece, which is caused by the chosen scheme of deformation. Proposed approaches for further research.

  • Open Access

    RISKS OF INJURY AND HEALTH DAMAGE WHEN USING BLACKSMITH EQUIPMENT

    by Oleg Kruzhylko, Vitaliy Chukhlib, Ihor Berezutskyi

    The article identifies the need to analyze the risks of injury and health damage when using blacksmith equipment which is due to the implementation of the latest technologies for the successful economic development of the country, the introduction of a risk-oriented approach, as well as the implementation of international standards in all sectors of the economy. It was noted that international standards are based on the use of a risk-oriented approach in solving issues of safety and occupational health of employees. Therefore, this requires the implementation of new approaches and the formation of new relationships in particularly dangerous areas of production. The general state of occupational injuries and deaths of workers in Ukraine for the period starting from 2022 to 2024 (four months of the current year) is given. The given data indicate an increase in the number of accidents at work which is further complicated by the war. These data indicate an increase in injuries at work which is a bad indicator and the need to implement modern risk-oriented technologies in the metallurgical industry. Analyzing the situation in the metallurgical industry where blacksmith equipment is widely used it should be noted that the main causes of injury and death of workers are organizational. This proves that the risk management system at enterprises is imperfect and needs to be improved and brought into line with international standards. Scientific approaches to determining the risks of injury and damage to the health of workers (operators) when using blacksmith equipment are considered. It is shown that modern technologies of metal processing by forging as one of the methods of pressure processing, use more and more robotic complexes which have risks associated with the organization of work in the conditions of the probability of physical impact of their individual elements and substances on workers. The dangerous and harmful factors that accompany the work of operators when using the MKP10 forging manipulator are given. The operation of the MKP10 manipulator is considered as an example. Tables and diagrams of the manipulator are made in accordance with the DSTU ISO 12100:2016 standard. The calculation of the risk indicator of the MKP10 manipulator was also performed which showed that the risk is average in terms of its damage and probability indicators. This leads to the need to apply risk management to control such risk and reduce it to acceptably small values.

  • Open Access

    APPROACH TO REDUCING THE NUMBER OF TECHNOLOGICAL TRANSITIONS IN THE PRODUCTION OF BENT PROFILES

    by Oleksii Saienko, Serhii Hubskyi, Vitaliy Chukhlib, Nikolay Sergienko, Kostiantyn Kolisnyk

    The article provides a generalized overview of approaches to reducing the number of technological transitions when reducing the production of bent profiles. In particular, various methods of producing bent profiles are considered, taking into account the requirements for the final product. The calculation of calibration of the production of trough profiles according to two calibration schemes has been developed. This calculation allows for an efficient production process of bent profiles and helps to reduce the number of technological transitions required to achieve the desired result. The production of a trough profile was modeled and graphs illustrating the profile manufacturing process were created. This made it possible to visualize various aspects of the technological process and find out which methods and calibration schemes are most effective for achieving the goal. Based on the data obtained, reasonable conclusions were drawn. These conclusions indicate which approaches and methods for producing bent profiles are optimal when reducing the number of process transitions. The results of the study can be useful for industrial enterprises engaged in the production of bent profiles, helping them to choose the most effective methods and calibration schemes to improve the production process and reduce costs.


  • Open Access

    TELEMETRY SYSTEMS FOR MONITORING DYNAMIC LOADS ON TRANSMISSION SYSTEM SHAFTS

    by Dmytro Cherkashyn, Sergii Hubskyi, Vitalij Chukhlib

    The article provides an overview of telemetry systems used to measure rotational vibrations in industrial sectors. Indications advantages and disadvantages of various principles of measurement and transmission of measured data from shafts rotating in the drive lines of rolling mills and transmission systems. The article describes the developed digital telemetry meters of rotational vibrations as part of a stationary dynamic load monitoring system with functions for diagnosing wear (angular gaps), which are used to monitor the torque, which helps prevent breakdowns, allows you to plan maintenance and increases productivity.


  • Open Access

    MODELLING OF SHAPING OF ROLL-FORMED SECTION WITH VARIABLE SECTION

    by Serhii Hubskyi, Vitalij Chukhlib, Mykola Biba

    In article the generalizing overview of approaches to production of the roll-formed sections of variable section used in the world is carried out. The relevance of use of modeling of tensely deformed condition of a profile by a finite element method for the purpose of forecasting of appearance of defects by its production is considered. It is pointed out demand of profiles with variable section. The scheme of molding is described, and the possibility of reasonable reduction of number of technological transitions is specified. Modeling of shaping of trough roll-formed section with variable cross-section with the lower horizontal wall is executed, the algorithm of a task of boundary coditions is shown. Change of the intense deformed condition of preparation at its passing through a cage of a camp is considered.