Carlos Alberto Brayner de Oliveira Lira
Carlos Alberto Brayner de Oliveira Lira has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Abel Gámez Rodríguez
Universidade Federal de Pernambuco
5 shared publications - Dany Sanchez Dominguez
Universidade Estadual de Santa Cruz
3 shared publications - Carlos García
Univ La Habana, Inst Super Tecnol & Ciencias Aplicadas InSTEC, Ave Salvador Allende 1110, Havana 10400, Cuba
2 shared publications - Carlos Rafael García Hernández
Instituto Superior de Tecnologías y Ciencias Aplicadas (InSTEC), Universidad de La Habana
2 shared publications - Daniel Evelio Mi̇li̇an Lorenzo
Universidad de La Habana
2 shared publications - Daniel Milian Pérez
Department of Nuclear Energy, Federal University of Pernambuco, Av. Prof. Luiz Freire, 1000, Cidade Universitária, Recife 50740-540, PE, Brazil
2 shared publications
Latest Publications
- Open Access
- 2 May 2026
- Published by Elsevier in SSRN Electronic Journal
Neutronic and thermal-hydraulic analysis for an integral pressurized water reactor with Thorium-Based Mixed-Oxide Fuels
The growth of nuclear energy is linked to the public's perception of the environmental impact associated with nuclear power plants and their fuel cycles. Therefore, sustainability has become a fundamental requirement, regarded as being as important as nuclear safety, the rational use of natural resources, the minimization of radioactive waste and resistance to proliferation. The expected increase in the use of nuclear fuels for energy generation this century calls for the use of other actinides in addition to uranium. The development of small modular reactors (SMR) for immediate and short-term deployment is advancing worldwide. This work focuses on the analysis of a small modular integral pressurized water reactor (iPWR) with Thorium-Uranium-Plutonium and Thorium-Plutonium (ThUPu and ThPu MOX) fuel mixture configurations. The feasibility of using MOX fuel was studied, considering the core partially loaded with MOX fuel, to guarantee an extended cycle of 48 months. One third of the core (24 fuel assemblies) was loaded with MOX fuel, while the remainder was loaded with standard UO2 fuel. It is proposed to develop a computational model that allows the study and optimization of physical-neutron parameters and the calculation of thermal-hydraulic parameters of the core of an IPWR reactor, based on SERPENT and OPENFOAM, respectively, for the study of extended fuel cycles. Strategies to control reactivity in extended four-year fuel cycles were studied. A thermal-hydraulic study of the hottest subchannel for the different MOX mixtures was carried out. The axial and radial temperature distributions in the fuel and coolant were calculated.
- 2 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessNeutronic and thermal-hydraulic analysis for an integral pressurized water reactor with Thorium-Based Mixed-Oxide Fuels
The growth of nuclear energy is linked to the public's perception of the environmental impact associated with nuclear power plants and their fuel cycles. Therefore, sustainability has become a fundamental requirement, regarded as being as important as nuclear safety, the rational use of natural resources, the minimization of radioactive waste and resistance to proliferation. The expected increase in the use of nuclear fuels for energy generation this century calls for the use of other actinides in addition to uranium. The development of small modular reactors (SMR) for immediate and short-term deployment is advancing worldwide. This work focuses on the analysis of a small modular integral pressurized water reactor (iPWR) with Thorium-Uranium-Plutonium and Thorium-Plutonium (ThUPu and ThPu MOX) fuel mixture configurations. The feasibility of using MOX fuel was studied, considering the core partially loaded with MOX fuel, to guarantee an extended cycle of 48 months. One third of the core (24 fuel assemblies) was loaded with MOX fuel, while the remainder was loaded with standard UO2 fuel. It is proposed to develop a computational model that allows the study and optimization of physical-neutron parameters and the calculation of thermal-hydraulic parameters of the core of an IPWR reactor, based on SERPENT and OPENFOAM, respectively, for the study of extended fuel cycles. Strategies to control reactivity in extended four-year fuel cycles were studied. A thermal-hydraulic study of the hottest subchannel for the different MOX mixtures was carried out. The axial and radial temperature distributions in the fuel and coolant were calculated.
- Open Access
- 5 February 2025
- Published by Sociedade Brasileira de Proteção Radiológica - SBPR in Brazilian Journal of Radiation Sciences
- Vol. 12 (4B (Suppl.) , e2760
Computational analysis of wax deposition in deep-water pipelines using nuclear techniques
Wax deposition in oil pipelines is a problem that affects flow assurance because it restricts production and, in more extreme cases, causes pipeline blockages. This problem occurs more frequently in offshore environments, where most of Brazil's reservoirs are located and where the ocean temperature at great depths is around 5°C. Detecting the wax layer on the inside walls of pipelines at an early stage avoids unscheduled stoppages and major economic losses. Among the various methods and techniques found in the literature for monitoring wax deposition, nuclear techniques are distinguished by the fact that their use does not interfere with the physical integrity of the pipeline, by the non-intrusive and indirect (non-contact) mode of operation and, therefore, does not affect the oil transportation process. This paper presents a computational model using the Monte Carlo N-Particle 6 (MCNP6) code and the gamma radiation transmission profiling technique to detect the presence of wax on the inner walls of pipelines used for deepwater oil transportation. The results of this study show that the model can detect the presence of up to 5% wax (in relation to the internal radius of the pipeline) with an accuracy of 7.4% in pipelines used in deep waters.
- 5 February 2025
- Published by Sociedade Brasileira de Proteção Radiológica - SBPR in Brazilian Journal of Radiation Sciences
- Vol. 12 (4B (Suppl.) , e2760
Open AccessComputational analysis of wax deposition in deep-water pipelines using nuclear techniques
Wax deposition in oil pipelines is a problem that affects flow assurance because it restricts production and, in more extreme cases, causes pipeline blockages. This problem occurs more frequently in offshore environments, where most of Brazil's reservoirs are located and where the ocean temperature at great depths is around 5°C. Detecting the wax layer on the inside walls of pipelines at an early stage avoids unscheduled stoppages and major economic losses. Among the various methods and techniques found in the literature for monitoring wax deposition, nuclear techniques are distinguished by the fact that their use does not interfere with the physical integrity of the pipeline, by the non-intrusive and indirect (non-contact) mode of operation and, therefore, does not affect the oil transportation process. This paper presents a computational model using the Monte Carlo N-Particle 6 (MCNP6) code and the gamma radiation transmission profiling technique to detect the presence of wax on the inner walls of pipelines used for deepwater oil transportation. The results of this study show that the model can detect the presence of up to 5% wax (in relation to the internal radius of the pipeline) with an accuracy of 7.4% in pipelines used in deep waters.
- Open Access
- 2 December 2024
- Published by RGSA- Revista de Gestao Social e Ambiental in Revista de Gestão Social e Ambiental
- Vol. 18 (12) , e010630
Sustainable Advancements in Aqueous Homogeneous Reactors: Thermal-Hydraulic Behavior and Radiolytic Gas Bubble Dynamics in Uranyl Sulfate Solutions
Objective: This study aims to analyze the thermal-hydraulic behavior and radiolytic gas bubble dynamics in uranyl sulfate solutions within Aqueous Homogeneous Reactors (AHR), emphasizing their potential for sustainable medical isotope production. Theoretical Framework: The research builds upon nuclear reactor theories, particularly those concerning radiolytic gas dynamics and thermal-hydraulic interactions. It highlights the advantages of AHR as a technology aligned with global sustainability goals by enhancing efficiency and reducing waste. Method: Computational Fluid Dynamics (CFD) simulations were conducted using the ANSYS-CFX software on a conceptual AHR design derived from the ARGUS reactor. Key parameters such as fuel solution temperature, velocity, and gas volume fraction were analyzed under varying conditions of radiolytic gas generation. Results and Discussion: The simulations revealed significant impacts of radiolytic gas bubble formation on reactor performance. A reduction in bubble generation from 100% to 10% increased the average fuel solution temperature by 3.96°C and decreased its velocity by 50%. Bubble velocity and volumetric gas fraction reductions of 68% and 46%, respectively, resulted in lower turbulence intensity, affecting thermal-hydraulic behavior. Research Implications: These findings demonstrate the dual role of radiolytic bubbles as both a challenge and an opportunity to optimize reactor safety, efficiency, and sustainability, contributing to advancements in green nuclear technology for medical applications. Originality/Value: This study contributes to the literature by integrating sustainability considerations into AHR analysis, offering innovative insights into managing radiolytic gas effects to enhance reactor design and operation.
- 2 December 2024
- Published by RGSA- Revista de Gestao Social e Ambiental in Revista de Gestão Social e Ambiental
- Vol. 18 (12) , e010630
Open AccessSustainable Advancements in Aqueous Homogeneous Reactors: Thermal-Hydraulic Behavior and Radiolytic Gas Bubble Dynamics in Uranyl Sulfate Solutions
Objective: This study aims to analyze the thermal-hydraulic behavior and radiolytic gas bubble dynamics in uranyl sulfate solutions within Aqueous Homogeneous Reactors (AHR), emphasizing their potential for sustainable medical isotope production. Theoretical Framework: The research builds upon nuclear reactor theories, particularly those concerning radiolytic gas dynamics and thermal-hydraulic interactions. It highlights the advantages of AHR as a technology aligned with global sustainability goals by enhancing efficiency and reducing waste. Method: Computational Fluid Dynamics (CFD) simulations were conducted using the ANSYS-CFX software on a conceptual AHR design derived from the ARGUS reactor. Key parameters such as fuel solution temperature, velocity, and gas volume fraction were analyzed under varying conditions of radiolytic gas generation. Results and Discussion: The simulations revealed significant impacts of radiolytic gas bubble formation on reactor performance. A reduction in bubble generation from 100% to 10% increased the average fuel solution temperature by 3.96°C and decreased its velocity by 50%. Bubble velocity and volumetric gas fraction reductions of 68% and 46%, respectively, resulted in lower turbulence intensity, affecting thermal-hydraulic behavior. Research Implications: These findings demonstrate the dual role of radiolytic bubbles as both a challenge and an opportunity to optimize reactor safety, efficiency, and sustainability, contributing to advancements in green nuclear technology for medical applications. Originality/Value: This study contributes to the literature by integrating sustainability considerations into AHR analysis, offering innovative insights into managing radiolytic gas effects to enhance reactor design and operation.
- Open Access
- 1 June 2024
- Published by International Centre for Applied Thermodynamics (ICAT) in International Journal of Thermodynamics
- Vol. 27 (2) , 75-87
Thermohydraulic Analysis of Coolant Entry Patterns in a High-Temperature Pebble Bed Reactor: Insights and Characterization
Conducting three-dimensional thermohydraulic analysis of an entire nuclear reactor poses significant challenges due to the considerable geometric volume and complex internal structures involved. The top reflector is one of the internal structures found in high-temperature pebble bed Small Modular Reactors (SMR). This structure serves several critical functions, including neutron reflection, control and distribution of helium inlet into the core, neutron and thermal shielding, among others. In this kind of system, the detailed representation of the top reflector includes the representation of more than 460 channels of 2.5cm of diameter. Considering that the reactor has almost a ten of meters then dimension scales of various orders must be represented, which is a challenge. In this sense, a three-dimensional Computational Fluid Dynamics (CFD) thermohydraulic analysis of the entry pattern to the core of a High Temperature SMR using ANSYS CFX has been done. This study presents a comparison between five coolant entry patterns into the core. Initially, two prototype models of 460x2.5cm, one with vertical channels and another with inclined channels, are modeled. Additionally, two prototype models of 20x12cm of equivalent area, with vertical and inclined channels are also included. Finally, a simplified porous media model with the same equivalent area is considered. The thermohydraulic behavior of the coolant before and after passing through the top reflector was then analyzed for these five patterns. An analysis of fuel elements temperature in the core was conducted. It is important to highlight that this study is qualitative and has the goal of identifying and characterizing the impact that the coolant entry pattern into the reactor core has on the main thermohydraulic parameters in this region. The study exposes a strong correlation between the porous media model and all prototype models in terms of the maximum fuel temperature, average fuel temperature, and helium velocity. In this study, the potential applicability of the porous media models for an integral full-scale reactor simulation in the future was demonstrated. As a benefit, the porous media model reduces the mesh quantity compared to a prototypic model.
- 1 June 2024
- Published by International Centre for Applied Thermodynamics (ICAT) in International Journal of Thermodynamics
- Vol. 27 (2) , 75-87
Open AccessThermohydraulic Analysis of Coolant Entry Patterns in a High-Temperature Pebble Bed Reactor: Insights and Characterization
Conducting three-dimensional thermohydraulic analysis of an entire nuclear reactor poses significant challenges due to the considerable geometric volume and complex internal structures involved. The top reflector is one of the internal structures found in high-temperature pebble bed Small Modular Reactors (SMR). This structure serves several critical functions, including neutron reflection, control and distribution of helium inlet into the core, neutron and thermal shielding, among others. In this kind of system, the detailed representation of the top reflector includes the representation of more than 460 channels of 2.5cm of diameter. Considering that the reactor has almost a ten of meters then dimension scales of various orders must be represented, which is a challenge. In this sense, a three-dimensional Computational Fluid Dynamics (CFD) thermohydraulic analysis of the entry pattern to the core of a High Temperature SMR using ANSYS CFX has been done. This study presents a comparison between five coolant entry patterns into the core. Initially, two prototype models of 460x2.5cm, one with vertical channels and another with inclined channels, are modeled. Additionally, two prototype models of 20x12cm of equivalent area, with vertical and inclined channels are also included. Finally, a simplified porous media model with the same equivalent area is considered. The thermohydraulic behavior of the coolant before and after passing through the top reflector was then analyzed for these five patterns. An analysis of fuel elements temperature in the core was conducted. It is important to highlight that this study is qualitative and has the goal of identifying and characterizing the impact that the coolant entry pattern into the reactor core has on the main thermohydraulic parameters in this region. The study exposes a strong correlation between the porous media model and all prototype models in terms of the maximum fuel temperature, average fuel temperature, and helium velocity. In this study, the potential applicability of the porous media models for an integral full-scale reactor simulation in the future was demonstrated. As a benefit, the porous media model reduces the mesh quantity compared to a prototypic model.
- 18 November 2021
- Published by Universidade Federal do Rio Grande in VETOR - Revista de Ciências Exatas e Engenharias
- Vol. 31 (1) , 84-93
Simulação Neutrônica do Núcleo de um Reator Nuclear do Tipo iPWR Usando o Código SERPENT
A energia nuclear é uma das principais alternativas para futuras fontes de energia sem emissões de gases contribuintes ao efeito estufa. Neste contexto os reatores nucleares modulares de pequeno porte têm grande potencial de desenvolvimento. Nesta categoria, por suas características de segurança e semelhanças com os reatores atuais em operação, destacam-se os reatores integrais de água pressurizada (iPWR). Neste trabalho, é apresentado um modelo computacional neutrônico baseado no código Monte Carlo Serpent para o projeto e análise de um ciclo de combustível estendido de quatro anos em um reator de tipo iPWR. Os principais parâmetros do comportamento neutrônico do núcleo são calculados e comparados com as recomendações para retores refrigerados a água.
- 18 November 2021
- Published by Universidade Federal do Rio Grande in VETOR - Revista de Ciências Exatas e Engenharias
- Vol. 31 (1) , 84-93
Simulação Neutrônica do Núcleo de um Reator Nuclear do Tipo iPWR Usando o Código SERPENT
A energia nuclear é uma das principais alternativas para futuras fontes de energia sem emissões de gases contribuintes ao efeito estufa. Neste contexto os reatores nucleares modulares de pequeno porte têm grande potencial de desenvolvimento. Nesta categoria, por suas características de segurança e semelhanças com os reatores atuais em operação, destacam-se os reatores integrais de água pressurizada (iPWR). Neste trabalho, é apresentado um modelo computacional neutrônico baseado no código Monte Carlo Serpent para o projeto e análise de um ciclo de combustível estendido de quatro anos em um reator de tipo iPWR. Os principais parâmetros do comportamento neutrônico do núcleo são calculados e comparados com as recomendações para retores refrigerados a água.
- 1 March 2021
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 373, 111011
An integral 3D full-scale steady-state thermohydraulic calculation of the high temperature pebble bed gas-cooled reactor HTR-10
- 1 March 2021
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 373, 111011
An integral 3D full-scale steady-state thermohydraulic calculation of the high temperature pebble bed gas-cooled reactor HTR-10
- 28 February 2021
- Published by International Centre for Applied Thermodynamics (ICAT) in International Journal of Thermodynamics
- Vol. 24 (1) , 9-22
Multi-physics evaluation of the steady-state operation of an Aqueous Homogeneous Reactor for producing Mo-99 for the Brazilian demand
The studies summarized in this paper aims to predict the steady state operation of a low-enriched uranium fuel ARGUS type aqueous homogeneous reactor for producing 99Mo to meet the domestic demand of Brazil through a coupled multi-physics (Neutronics + Thermal-hydraulics) evaluation. The coupled multi-physics evaluation included aspects related to the neutronic behavior such as fission induced energy deposition profile, medical isotopes production; and the thermal-hydraulic behavior such as temperature, velocities and gas volume fraction profiles. The methodology followed for the multi-physics and multi-scale coupling of the neutronic and thermal-hydraulic codes (MCNP + ANSYS-CFX), discussed in detail in this paper, represent one of the main outcomes of the current study. The methodology was tested for two different operating configurations of the ARGUS reactor, the original high-enriched uranium configuration used since 1981, and the new low-enriched uranium configuration after the conversion process during 2012-2014. The calculations carried out showed that the reactor, in the studied configuration, is able to produce 246.5 six days Curie of 99Mo in operation cycles of five days. Which is equivalent to more than a third of the estimated Brazilian demand for 2025.
- 28 February 2021
- Published by International Centre for Applied Thermodynamics (ICAT) in International Journal of Thermodynamics
- Vol. 24 (1) , 9-22
Multi-physics evaluation of the steady-state operation of an Aqueous Homogeneous Reactor for producing Mo-99 for the Brazilian demand
The studies summarized in this paper aims to predict the steady state operation of a low-enriched uranium fuel ARGUS type aqueous homogeneous reactor for producing 99Mo to meet the domestic demand of Brazil through a coupled multi-physics (Neutronics + Thermal-hydraulics) evaluation. The coupled multi-physics evaluation included aspects related to the neutronic behavior such as fission induced energy deposition profile, medical isotopes production; and the thermal-hydraulic behavior such as temperature, velocities and gas volume fraction profiles. The methodology followed for the multi-physics and multi-scale coupling of the neutronic and thermal-hydraulic codes (MCNP + ANSYS-CFX), discussed in detail in this paper, represent one of the main outcomes of the current study. The methodology was tested for two different operating configurations of the ARGUS reactor, the original high-enriched uranium configuration used since 1981, and the new low-enriched uranium configuration after the conversion process during 2012-2014. The calculations carried out showed that the reactor, in the studied configuration, is able to produce 246.5 six days Curie of 99Mo in operation cycles of five days. Which is equivalent to more than a third of the estimated Brazilian demand for 2025.
- 1 January 2021
- Published by International Centre for Applied Thermodynamics (ICAT) in International Journal of Thermodynamics
- Vol. 24 (4) , 125-133
Implementation of a Multi-cell Approach in the Multi-Physics Calculations of an Aqueous Homogeneous Reactor
Nowadays, the Aqueous Homogeneous Reactor (AHR) technology is under study for its use in the production of medical isotopes. This technology has proven to be potentially advantageous for this purpose due to its low cost, small critical mass, inherent passive safety, and simplified fuel handling, processing, and purification characteristics. Among the studies being carried out is computational modeling and simulation, which represents a key technology in the pursuit for improvements in efficiency, safety, and reliability of these systems. This paper aims to expand upon a previous AHR computational model through the implementation of a multi-cell approach for the improvement of the calculations using a methodology for the multi-physics and multi-scale coupling of the neutronic and thermal-hydraulic codes. It was found that these additions to the original model cause a small change to the overall reactor behavior. Thermal-hydraulic parameters such as, average fuel solution temperature and velocity, gas volume fraction and average radiolytic gas bubbles velocity undergo a variation of 0.161 degrees C, 0.0009 m/s, 0.015% and 0.0003 m/s. In contrast, significant local differences were obtained mainly for the fuel solution temperature and radiolytic gas bubbles volume fraction. It was verified that a simplified AHR computational model consisting of a 20 degrees section of the fuel solution is able to adequately reproduce the results of the full AHR computational model.
- 1 January 2021
- Published by International Centre for Applied Thermodynamics (ICAT) in International Journal of Thermodynamics
- Vol. 24 (4) , 125-133
Implementation of a Multi-cell Approach in the Multi-Physics Calculations of an Aqueous Homogeneous Reactor
Nowadays, the Aqueous Homogeneous Reactor (AHR) technology is under study for its use in the production of medical isotopes. This technology has proven to be potentially advantageous for this purpose due to its low cost, small critical mass, inherent passive safety, and simplified fuel handling, processing, and purification characteristics. Among the studies being carried out is computational modeling and simulation, which represents a key technology in the pursuit for improvements in efficiency, safety, and reliability of these systems. This paper aims to expand upon a previous AHR computational model through the implementation of a multi-cell approach for the improvement of the calculations using a methodology for the multi-physics and multi-scale coupling of the neutronic and thermal-hydraulic codes. It was found that these additions to the original model cause a small change to the overall reactor behavior. Thermal-hydraulic parameters such as, average fuel solution temperature and velocity, gas volume fraction and average radiolytic gas bubbles velocity undergo a variation of 0.161 degrees C, 0.0009 m/s, 0.015% and 0.0003 m/s. In contrast, significant local differences were obtained mainly for the fuel solution temperature and radiolytic gas bubbles volume fraction. It was verified that a simplified AHR computational model consisting of a 20 degrees section of the fuel solution is able to adequately reproduce the results of the full AHR computational model.
- 1 November 2019
- Published by Elsevier in Progress in Nuclear Energy
- Vol. 117
New advances in the conceptual design of a transmutation advanced device for sustainable energy applications (TADSEA)
- 1 November 2019
- Published by Elsevier in Progress in Nuclear Energy
- Vol. 117
New advances in the conceptual design of a transmutation advanced device for sustainable energy applications (TADSEA)