Lin Cheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Lin Cheng has a total of 144 co-authors. Here are the top co-authors by number of shared publications:
- Dongfang Pan
University of Science and Technology of China
13 shared publications - Wing-Hung Ki
The Hong Kong University of Science and Technology
11 shared publications Wing-Hung Ki
8 shared publications- Jing Wang
School of Microelectronics, University of Science and Technology of China, Hefei, China
5 shared publications - Yichao Ji
University of Science and Technology of China
5 shared publications Bill Yang Liu
Analog Devices Inc., Shanghai, China
4 shared publications
Latest Publications
- 1 December 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (12) , 21391-21404
An Interleaved-Fibonacci Always-Dual-Path Buck Converter With Large Voltage Conversion Ratio and Reduced Inductor Current
- 1 December 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (12) , 21391-21404
An Interleaved-Fibonacci Always-Dual-Path Buck Converter With Large Voltage Conversion Ratio and Reduced Inductor Current
- 7 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-12
An Ultralow Cross-Regulation Single-Inductor Multiple-Output (SIMO) Buck Converter Using Reordered Power-Distributive Control
A single-inductor multiple-output (SIMO) buck converter employing reordered power-distributive control (RPDC) is presented to achieve ultralow cross regulation. Adedicated power-distribution controller implements RPDC by adaptively adjusting the switching sequence: when the inductor current is insufficient, the switching period is extended, and when excessive, an end phase in the form of a freewheeling phase is inserted to minimize cross regulation. During large transients, RPDC is activated; aided by transient detection and processing (TDP), the controller prioritizes victim outputs and defers transient outputs to the end phase, thereby further suppressing cross regulation without hurting the transient outputs. The converter, fabricated in a 0.18- $\mu $ m BCD process with all power transistors integrated on-chip, demonstrates a measured voltage droop of 188mV and cross regulation of 9mV/A in the worst-case scenario under a 2-A load transient. Without the freewheeling period in the steady state, the converter achieves a peak efficiency of 89.6% at 2.7W.
- 7 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-12
An Ultralow Cross-Regulation Single-Inductor Multiple-Output (SIMO) Buck Converter Using Reordered Power-Distributive Control
A single-inductor multiple-output (SIMO) buck converter employing reordered power-distributive control (RPDC) is presented to achieve ultralow cross regulation. Adedicated power-distribution controller implements RPDC by adaptively adjusting the switching sequence: when the inductor current is insufficient, the switching period is extended, and when excessive, an end phase in the form of a freewheeling phase is inserted to minimize cross regulation. During large transients, RPDC is activated; aided by transient detection and processing (TDP), the controller prioritizes victim outputs and defers transient outputs to the end phase, thereby further suppressing cross regulation without hurting the transient outputs. The converter, fabricated in a 0.18- $\mu $ m BCD process with all power transistors integrated on-chip, demonstrates a measured voltage droop of 188mV and cross regulation of 9mV/A in the worst-case scenario under a 2-A load transient. Without the freewheeling period in the steady state, the converter achieves a peak efficiency of 89.6% at 2.7W.
- 6 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (5) , 598-602
A Low-Quiescent-Current Output-Capacitorless Low-Dropout Regulator With a Dual-Path Adaptive-Biasing Technique
This brief presents an output-capacitorless low-dropout regulator (OCL-LDO) featuring low power consumption and fast transient response. A dual-path adaptive-biasing (DP-AB) technique is introduced, improving conventional adaptive biasing for IoT applications. The proposed LDO uses a negative-feedback path to adaptively counteract positive-feedback component of conventional adaptive biasing under light loads, suppressing inner-loop gain for enhanced stability without raising quiescent current, while preserving heavy-load performance. Fabricated in a 180-nm BCD process with a core area of 0.021 mm2, it achieves 2.2 μA quiescent current and 40 mA maximum load. Measurements show 0.16-V undershoot and 168-ns recovery for a 0 A to 40 mA load step with 75-ns edge time. By overcoming conventional adaptive-biasing power limitations, the design delivers low static current and rapid transient response.
- 6 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (5) , 598-602
A Low-Quiescent-Current Output-Capacitorless Low-Dropout Regulator With a Dual-Path Adaptive-Biasing Technique
This brief presents an output-capacitorless low-dropout regulator (OCL-LDO) featuring low power consumption and fast transient response. A dual-path adaptive-biasing (DP-AB) technique is introduced, improving conventional adaptive biasing for IoT applications. The proposed LDO uses a negative-feedback path to adaptively counteract positive-feedback component of conventional adaptive biasing under light loads, suppressing inner-loop gain for enhanced stability without raising quiescent current, while preserving heavy-load performance. Fabricated in a 180-nm BCD process with a core area of 0.021 mm2, it achieves 2.2 μA quiescent current and 40 mA maximum load. Measurements show 0.16-V undershoot and 168-ns recovery for a 0 A to 40 mA load step with 75-ns edge time. By overcoming conventional adaptive-biasing power limitations, the design delivers low static current and rapid transient response.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (8) , 1
A Low-Power 2 nd -Order ΔΣ Modulator with a Single Current-Starving FIA
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (8) , 1
A Low-Power 2 nd -Order ΔΣ Modulator with a Single Current-Starving FIA
- 31 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
A Ka-Band Variable-Gain Phase Shifter Using a Merged Phase-Shifted and Attenuated Unit
This article presents a compact variable-gain phase shifter (VGPS) that incorporates both a merged phase-shifted attenuator (ATT) and a merged attenuated phase shifter (PS) unit. The merged phase-shifted ATT achieves an additional phase-shifting capability using a modified switched $\pi $ -type ATT structure, while the merged attenuated PS provides an additional attenuation function based on revised high-pass/low-pass or high-pass/direct-pass PS topologies. The proposed VGPS achieves a bidirectional 20.5-dB gain control range and a 360° phase control range with a 0.5-dB gain step and 5.625° phase step in standard 65 nm CMOS technology. Measurement results demonstrate a maximum root mean squares (rms) phase error of 3.3° and a maximum rms amplitude error of 0.37 dB across the 33–37GHz. The fully passive circuit exhibits high linearity, featuring a minimum input 1-dB compression point (IP1dB) of 11.1 dBm. The core size is 0.27 mm2 excluding pads.
- 31 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
A Ka-Band Variable-Gain Phase Shifter Using a Merged Phase-Shifted and Attenuated Unit
This article presents a compact variable-gain phase shifter (VGPS) that incorporates both a merged phase-shifted attenuator (ATT) and a merged attenuated phase shifter (PS) unit. The merged phase-shifted ATT achieves an additional phase-shifting capability using a modified switched $\pi $ -type ATT structure, while the merged attenuated PS provides an additional attenuation function based on revised high-pass/low-pass or high-pass/direct-pass PS topologies. The proposed VGPS achieves a bidirectional 20.5-dB gain control range and a 360° phase control range with a 0.5-dB gain step and 5.625° phase step in standard 65 nm CMOS technology. Measurement results demonstrate a maximum root mean squares (rms) phase error of 3.3° and a maximum rms amplitude error of 0.37 dB across the 33–37GHz. The fully passive circuit exhibits high linearity, featuring a minimum input 1-dB compression point (IP1dB) of 11.1 dBm. The core size is 0.27 mm2 excluding pads.
- 17 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (5) , 3102-3115
A Cryogenic HBT-CMOS Temperature Sensor Operating From 4 to 70 K
In current cryogenic temperature sensor (cryo-TS) systems, the sensing front-end and readout circuits typically operate in cryogenic and room-temperature environments, respectively. This paper proposes a scheme to integrate both the front-end devices and readout circuits of cryo-TS within the cryogenic environment to achieve lower noise, digital fan-out of temperature information, and cost reduction. We employed the silicon-germanium (SiGe) heterojunction bipolar transistors (HBT), which demonstrated excellent linearity and current gain even at cryogenic temperatures, as the sensing front end of the cryo-TS and a Zoom-ADC as its readout circuits. A redundancy bit is introduced in the cryogenic readout ADC to avoid temperature misjudgment. The design methodology and key considerations for implementing cryogenic readout analog circuits are presented. Implemented in a 65 nm CMOS process, the cryo-TS achieved a 1-point-trimmed (at 40 K) inaccuracy of ±0.54 K ( $\boldsymbol {3\sigma }$ ) from 4 K to 70 K under a supply current of 22.13 $\mu A$ .
- 17 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (5) , 3102-3115
A Cryogenic HBT-CMOS Temperature Sensor Operating From 4 to 70 K
In current cryogenic temperature sensor (cryo-TS) systems, the sensing front-end and readout circuits typically operate in cryogenic and room-temperature environments, respectively. This paper proposes a scheme to integrate both the front-end devices and readout circuits of cryo-TS within the cryogenic environment to achieve lower noise, digital fan-out of temperature information, and cost reduction. We employed the silicon-germanium (SiGe) heterojunction bipolar transistors (HBT), which demonstrated excellent linearity and current gain even at cryogenic temperatures, as the sensing front end of the cryo-TS and a Zoom-ADC as its readout circuits. A redundancy bit is introduced in the cryogenic readout ADC to avoid temperature misjudgment. The design methodology and key considerations for implementing cryogenic readout analog circuits are presented. Implemented in a 65 nm CMOS process, the cryo-TS achieved a 1-point-trimmed (at 40 K) inaccuracy of ±0.54 K ( $\boldsymbol {3\sigma }$ ) from 4 K to 70 K under a supply current of 22.13 $\mu A$ .