CLChun-Ping Lin

Chun-Ping Lin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Chun-Ping Lin has a total of 69 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Biomass-Derived Ester-Rich Insulating Fluids from Soybean and Canola Oils: Route-Specific Synthesis and Preliminary Performance Screening

    by Shu-Yao Tsai, Ting-Wei Hsieh, Min Huang, Chun-Ping Lin

    The valorization of vegetable-oil biomass into bio-based functional fluids offers a sustainable route for replacing petroleum-derived insulating liquids in power equipment. In this study, soybean and canola oils were used as renewable lipid feedstocks and converted into biomass-derived ester fluids through acid-catalyzed transesterification with methanol, ethanol, 1-propanol, and 1-butanol. The obtained ester-rich products were subjected to a combined physicochemical, dielectric, and thermal screening workflow, including kinematic viscosity at 40 °C (ν40), acid value, breakdown voltage (BDV), differential scanning calorimetry (DSC; 2–8 °C min−1 under N2), and oxygen bomb calorimetry. Transesterification effectively upgraded the vegetable oils into low-viscosity ester-rich product fluids for most alcohol routes, with soybean methyl ester (SME) reaching 4.41 ± 0.02 mm2 s−1 and selected canola-derived esters showing viscosities of 5.81–6.81 mm2 s−1. However, the functional performance of the biomass-derived fluids was strongly governed by the alcohol route. SME exhibited the most favorable balance between dielectric and physicochemical properties, delivering the highest BDV of 64.90 ± 9.74 kV, exceeding the IEC 60156 threshold of 30 kV, while maintaining a low acid value of 0.0103 ± 0.0006 mg KOH g−1. In contrast, propyl- and butyl-derived esters showed substantially lower BDV values of ≤14.98 kV, whereas ethanol-derived products retained near-neat-oil viscosities and were unsuitable for BDV testing under the applied conditions. Although propyl- and butyl-derived ester-rich products reduced kinematic viscosity, their markedly lower BDV values were likely associated with route-dependent product heterogeneity, lower alcohol–oil miscibility, possible residual polar impurities, and moisture sensitivity; therefore, they were regarded as non-optimized screening outcomes rather than IEC-compliant transformer-fluid candidates. DSC analysis provided comparative thermal-response descriptors under nitrogen, with methylation producing more coherent endothermic features. The combustion heats of the ester-rich products were concentrated at approximately 39–41 MJ kg−1, lower than that of the mineral-oil reference in this dataset, suggesting combustion heat was used only as a preliminary energy-density descriptor and was not interpreted as direct evidence of improved fire safety. From an engineering-safety perspective, the lower combustion heat of the bio-esters may reduce the potential fire-load contribution during fault-related fire scenarios, although full fire-safety qualification requires additional flash-point, fire-point, and aging evaluations. Overall, this work demonstrates that alcohol route selection is a critical factor in converting vegetable oil biomass into high-value bio-based insulating fluids. Among the tested formulations, soybean methyl ester is the most promising baseline candidate for further development as a biodegradable, sustainable transformer fluid.

  • Open Access

    Greenhouse Gas Emissions and Mitigation Strategies in Universities Under ISO 14064-1: Lessons for Global Higher Education Sustainability

    by Shu-Yao Tsai, Mei-Ching Wang, Shun-Pei Yao, Gregory J. Tsay, Chun-Ping Lin

    In alignment with the United Nations’ Sustainable Development Goals (SDGs) and the global pursuit of net-zero emissions, higher education institutions (HEIs) are increasingly expected to demonstrate robust climate accountability and effective decarbonization strategies. This three-year longitudinal study presents a comprehensive assessment of greenhouse gas (GHG) emissions at a higher education institution, employing the ISO 14064-1:2018 framework to strengthen inventory design, boundary delineation, and data governance protocols. Findings indicate that purchased electricity constitutes the largest share; however, fugitive refrigerant leakage and Scope 3 activities—particularly commuting and business travel—represent substantial and often underestimated components of the institution’s carbon footprint. Methodological refinements, including the incorporation of updated emission factors coefficients and enhanced data verification, have revealed the sensitivity of GHG inventories to both policy reforms and behavioral changes, as well as institutional policy reforms. The study also demonstrates that targeted refrigerant management and low-carbon mobility initiatives can generate measurable mitigation effects, even under conditions of expanding campus activity. Beyond the institution-specific results, this research proposes a replicable framework that integrates ISO 14064-1 compliance with data quality assurance and digital verification tools. This framework provides HEIs globally with a structured pathway to enhance reporting credibility, develop evidence-based mitigation strategies, and accelerate progress toward carbon neutrality. These insights underline the strategic role of universities in advancing sector-wide climate leadership and contributing to sustainable development transitions.


  • From beetle to bot: bioinspired design of robotic grippers based on stag beetle mandible biomechanics

    by Mahdi Rajabi, Sepehr H Eraghi, Arman Toofani, Shayan Ramezanpour, Preenjot Singh, Jianing Wu, Chung-Ping Lin, Hamed Rajabi

    Conventional rigid grippers remain the most-used robotic grippers in industrial assembly tasks. However, they are limited in their ability to handle a diverse range of objects. This study draws inspiration from nature to address these limitations, employing multidisciplinary methods, such as computer-aided design, parametric modeling, finite element analysis, 3D printing, and mechanical testing. Computational analysis of three distinct mandible morphs from the stag beetle Cyclommatus mniszechi revealed that key geometric features—specifically mandible curvature and denticle arrangement—govern a functional trade-off between grasping ability and structural safety. This analysis identified a specific morphology optimized for superior grabbing performance, which served as the template for our design. Leveraging these biological principles, we used parametric modeling to design, and 3D printing to fabricate, a series of novel, mechanically intelligent grippers. Mechanical testing of these prototypes validated our design approach, demonstrating that specific modifications to curvature could significantly enhance the gripper’s load-bearing capacity while minimizing object damage. This work establishes a clear pathway from biomechanical analysis to engineered application, offering a robust and cost-efficient blueprint for developing next-generation grippers that operate effectively without complex sensing or actuation systems for tasks in manufacturing, logistics, and healthcare.


  • Antimicrobial activity effects of electrolytically generated hypochlorous acid-treated pathogenic microorganisms by isothermal kinetic simulation

    by Shu-Yao Tsai, Yu-Ming Liu, Zhi-Wei Lin, Chun-Ping Lin

    This study involves isothermal kinetic simulation to evaluate the parameters of inhibition conditions for Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) of high-risk pathogens. This is because the new type of the 2019 novel coronavirus (2019-nCoV) is continuously spreading and the importance of public health issues. Environmental disinfection and personal wearing of masks have become important epidemic prevention measures. Selection of concentration kinetics could be estimated best for E. coli and S. aureus of pathogens, 2.74 × 104 and 105 and 2.44 × 104 and 105 colony-forming units (CFU mL–1), by isothermal micro-calorimeter (TAM Air) tests, respectively. Comparisons were made of different doses of 0–70 ppm (in 20 mL test ampoule) hypochlorous acid treatment for conducting nth-order and autocatalytic reaction simulation to evaluate the inhibition reaction parameters, which determined the autocatalytic kinetic model that was beneficially applied on the E. coli and S. aureus. We developed the inhibition reaction parameters of the pathogens, which included the activation energy (Ea), the natural logarithm of pre-exponential factor (lnk0), the enthalpy of inhibition microbial growth reaction (∆H), inhibition microbial growth, and the inhibition growth analysis. Overall, we conducted isothermal kinetic simulation to understand the antimicrobial activity effects of electrolytically generated hypochlorous acid-treated pathogenic microorganisms, which will provide reference for public health and medical-related fields for SDG3, and can contribute to ensuring human health and hygiene.


  • Open Access

    The Potential of the Oil-Producing Oleaginous Yeast Rhodotorula mucilaginosa for Sustainable Production of Bio-Oil Energy

    by Shu-Yao Tsai, Hsuan-Ti Yu, Chun-Ping Lin

    At the 2021 United Nations Climate Change Conference (COP26), many countries in the world agreed to reach the goal of net-zero greenhouse gas emissions by 2050. This issue constrains energy use, petrochemical use, and related manufacturing production patterns. It is undeniable that the diesel engine of large equipment is still widely used in engineering applications, and it will not disappear in a short time. Many industrial projects still have to face the use of diesel engines. This study was focused on the development of oil-producing microorganisms to generate lipids. The oleaginous yeast Rhodotorula mucilaginosa (R. mucilaginosa) was selected for liquid-state cultivation, and the conditions for growth of the yeast cells were assessed. For the liquid fermentation culture with a fixed inoculation amount of 5%, it was determined that a suitable oil-producing culture was obtained on the sixth day, and the optimum conditions involved a carbon source concentration of 60 g/L, a yeast extract concentration of 0.5 g/L, and a KH2PO4 concentration of 7.0 g/L for each batch of culture experiments. In addition, the extraction method and solvent for the extraction of R. mucilaginosa lipids were chosen. The acid-heat method using the green organic solvent ethyl acetate exhibited the best performance for extraction of yeast lipids under environmentally friendly and safe conditions. The analysis of lipids showed that the fatty acids obtained primarily contained C16:0, C18:1 and C18:2, and especially C18:1 (41%) lipids, indicating that R. mucilaginosa lipids are a good bio-oil source for the production of biodiesel.


  • Open Access

    Assessment of Melting Kinetics of Sugar-Reduced Silver Ear Mushroom Ice Cream under Various Additive Models

    by Shu-Yao Tsai, Gregory J. Tsay, Chien-Yu Li, Yu-Tzu Hung, Chun-Ping Lin

    This study focuses on assessing the effects of various food processing silver ear (Tremella fuciformis) powders in sugar-reduced ice cream through melting kinetic simulation, sensory properties and functional ingredients. T. fuciformis, a natural anti-melting stabilizer in ice cream, has the advantage of functional ingredients. Using 100, 200, and 300 mesh of particle sizes, and then selecting a suitable particle size, those are added to the additive ratios of 0.4, 0.9, and 1.4% T. fuciformis powder to replace fresh T. fuciformis fruit body. Decreased particle size of T. fuciformis powder significantly increased ice cream stability. Comparisons of sensory evaluation and melting properties, in order to learn the differences of T. fuciformis ice cream under various stabilizer models, were evaluated and elucidated. Therefore, we obtained 300 mesh at 0.9% additive ratio of T. fuciformis powder, which is closest to the fresh fruit body/base ice cream. The enrichment of ice cream with T. fuciformis is to enhance the nutritional aspects and develop a functional food. Overall, the kinetic parameters of T. fuciformis ice cream melting can be provided as a reference for frozen dessert processing technology.