Svenja Tappe
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Svenja Tappe has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
Tobias Ortmaier
Institute of Mechatronic Systems (IMES) & Hannover Center of Mechatronics (MZH), Leibniz Universität Hannover, Hannover, Germany
20 shared publicationsJens Kotlarski
Forward ttc GmbH
6 shared publications- Elias Knochelmann
Leibniz University Hannover
5 shared publications - Moritz Schappler
Institute of Mechatronic Systems, Leibniz University Hannover, Garbsen, Germany
3 shared publications - Ahmed Zidan
Gottfried Wilhelm Leibniz Universita¨t Hannover
2 shared publications Alexander Mannel
Bosch Rexroth AG, Germany
2 shared publications
Latest Publications
- Open Access
- 24 January 2020
- Published by SAGE Publications in Measurement and Control
- Vol. 53 (3-4) , 613-626
Design of a low-cost tactile robotic sleeve for autonomous endoscopes and catheters
Recent developments in medical robotics have been significant, supporting the minimally invasive operation requirements, such as smaller devices and more feedback available to surgeons. Nevertheless, the tactile feedback from a catheter or endoscopic type robotic device has been restricted mostly on the tip of the device and was not aimed to support the autonomous movement of the medical device during operation. In this work, we design a robotic sheath/sleeve with a novel and more comprehensive approach, which can function for whole body or segment-based feedback control as well as diagnostic purposes. The robotic sleeve has several types of piezo-resistive pressure and extension sensors, which are embedded at several latitudes and depths of the silicone substrate. The sleeve takes the human skin as a biological model for its structure. It has a better tactile sensation of the inner tissues in the torturous narrow channels such as cardiovascular or endoluminal tracts in human body and thus can be used to diagnose abnormalities. In addition to this capability, using the stretch sensors distributed alongside its body, the robotic sheath/sleeve can perceive the ego-motion of the robotic backbone of the catheter and can act as a position feedback device. Because of the silicone substrate, the sleeve contributes toward safety of the medical device passively by providing a compliant interface. As an active safety measure, the robotic sheath can sense blood clots or sudden turns inside a channel and by modifying the local trajectory and can prevent embolisms or tissue rupture. In the future, advanced manufacturing techniques will increase the capabilities of the tactile robotic sleeve.
- 24 January 2020
- Published by SAGE Publications in Measurement and Control
- Vol. 53 (3-4) , 613-626
Open AccessDesign of a low-cost tactile robotic sleeve for autonomous endoscopes and catheters
Recent developments in medical robotics have been significant, supporting the minimally invasive operation requirements, such as smaller devices and more feedback available to surgeons. Nevertheless, the tactile feedback from a catheter or endoscopic type robotic device has been restricted mostly on the tip of the device and was not aimed to support the autonomous movement of the medical device during operation. In this work, we design a robotic sheath/sleeve with a novel and more comprehensive approach, which can function for whole body or segment-based feedback control as well as diagnostic purposes. The robotic sleeve has several types of piezo-resistive pressure and extension sensors, which are embedded at several latitudes and depths of the silicone substrate. The sleeve takes the human skin as a biological model for its structure. It has a better tactile sensation of the inner tissues in the torturous narrow channels such as cardiovascular or endoluminal tracts in human body and thus can be used to diagnose abnormalities. In addition to this capability, using the stretch sensors distributed alongside its body, the robotic sheath/sleeve can perceive the ego-motion of the robotic backbone of the catheter and can act as a position feedback device. Because of the silicone substrate, the sleeve contributes toward safety of the medical device passively by providing a compliant interface. As an active safety measure, the robotic sheath can sense blood clots or sudden turns inside a channel and by modifying the local trajectory and can prevent embolisms or tissue rupture. In the future, advanced manufacturing techniques will increase the capabilities of the tactile robotic sleeve.
- Open Access
Modeling Parallel Robot Kinematics for 3T2R and 3T3R Tasks Using Reciprocal Sets of Euler Angles
Industrial manipulators and parallel robots are often used for tasks, such as drilling or milling, that require three translational, but only two rotational degrees of freedom (“3T2R”). While kinematic models for specific mechanisms for these tasks exist, a general kinematic model for parallel robots is still missing. This paper presents the definition of the rotational component of kinematic constraints equations for parallel robots based on two reciprocal sets of Euler angles for the end-effector orientation and the orientation residual. The method allows completely removing the redundant coordinate in 3T2R tasks and to solve the inverse kinematics for general serial and parallel robots with the gradient descent algorithm. The functional redundancy of robots with full mobility is exploited using nullspace projection.
Open AccessModeling Parallel Robot Kinematics for 3T2R and 3T3R Tasks Using Reciprocal Sets of Euler Angles
Industrial manipulators and parallel robots are often used for tasks, such as drilling or milling, that require three translational, but only two rotational degrees of freedom (“3T2R”). While kinematic models for specific mechanisms for these tasks exist, a general kinematic model for parallel robots is still missing. This paper presents the definition of the rotational component of kinematic constraints equations for parallel robots based on two reciprocal sets of Euler angles for the end-effector orientation and the orientation residual. The method allows completely removing the redundant coordinate in 3T2R tasks and to solve the inverse kinematics for general serial and parallel robots with the gradient descent algorithm. The functional redundancy of robots with full mobility is exploited using nullspace projection.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 962-969
Online Learning of the Inverse Dynamics with Parallel Drifting Gaussian Processes: Implementation of an Approach for Feedforward Control of a Parallel Kinematic Industrial Robot
The present paper deals with an online approach to learn the inverse dynamics of any robot. This is realized by the use of Gaussian Processes drifting parallel along the system data. An extension by a database enables the efficient use of data points from the past. The central component of this work is the implementation of such a method in a controller in order to achieve the actual goal: the feedforward control of an industrial robot by means of machine learning. This is done by splitting the procedure into two threads running parallel so that the prediction is decoupled from the computing-intensive training of the models. Experiments show that the method reduces the tracking errors more clearly than an elaborately identified rigid body model including friction. For a defined trajectory, the squared areas of the tracking errors of all axes are reduced by more than 54% compared to motion without pre-control. In addition, a highly dynamic pick-and-place experiment is used to investigate the possible changes in system dynamics. Compared to an offline trained model, the approximation error of the proposed online approach is smaller for the remaining time of the experiment after an initial phase. Furthermore, this error is smaller throughout the experiment for online learning with parallel drifting Gaussian Processes than when using a single one.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 962-969
Online Learning of the Inverse Dynamics with Parallel Drifting Gaussian Processes: Implementation of an Approach for Feedforward Control of a Parallel Kinematic Industrial Robot
The present paper deals with an online approach to learn the inverse dynamics of any robot. This is realized by the use of Gaussian Processes drifting parallel along the system data. An extension by a database enables the efficient use of data points from the past. The central component of this work is the implementation of such a method in a controller in order to achieve the actual goal: the feedforward control of an industrial robot by means of machine learning. This is done by splitting the procedure into two threads running parallel so that the prediction is decoupled from the computing-intensive training of the models. Experiments show that the method reduces the tracking errors more clearly than an elaborately identified rigid body model including friction. For a defined trajectory, the squared areas of the tracking errors of all axes are reduced by more than 54% compared to motion without pre-control. In addition, a highly dynamic pick-and-place experiment is used to investigate the possible changes in system dynamics. Compared to an offline trained model, the approximation error of the proposed online approach is smaller for the remaining time of the experiment after an initial phase. Furthermore, this error is smaller throughout the experiment for online learning with parallel drifting Gaussian Processes than when using a single one.
- 18 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 24 (5) , 2171-2181
Design and Analysis of Electromagnetic Tilting Actuators
This paper studies the design and the behaviour of bistable electromagnetic tilting actuators (ETA). A serial chain of these actuators can be utilized as a medical or industrial endoscope. With the concept presented here, it is possible to unite flexibility and high stiffness in one shaft. An ETA is able to switch between defined positions through a tilting movement. The mechanical movement is driven by an electromagnetic torque, which is powered by a magneto motive force (MMF) in the coils of the ETA. The tilting torque is mainly influenced by the design of the magnetic path inside the ETA cores. The ETA chain is operated using a “Follow the Leader” control. Therefore, very fast calculation methods are necessary to evaluate power-on-durations and subsequently influence the tilting process itself. In this paper, the physical effects while operating are analyzed and the necessary calculation methods are elaborated. Since very high currents are applied for tilting, the electric network calculation includes a thermal model to consider the thermally driven asymmetric increase of resistivity as well. The analysis of the operational characteristic of the ETA is the basis of the time-efficient combined calculation method. Using this combined calculation, a complete tilting process of one or more ETA can be calculated in advance considering the chain configuration and external forces. Using this method, optimized power-on-durations can be evaluated, for which the tilting process itself is successful and no unintended impulsive forces are applied to the chain. The validation with measurements has proven the accuracy of the initial model (without parameter fitting) to a deviation of 15 % at most with a very small calculation time effort within seconds.
- 18 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 24 (5) , 2171-2181
Design and Analysis of Electromagnetic Tilting Actuators
This paper studies the design and the behaviour of bistable electromagnetic tilting actuators (ETA). A serial chain of these actuators can be utilized as a medical or industrial endoscope. With the concept presented here, it is possible to unite flexibility and high stiffness in one shaft. An ETA is able to switch between defined positions through a tilting movement. The mechanical movement is driven by an electromagnetic torque, which is powered by a magneto motive force (MMF) in the coils of the ETA. The tilting torque is mainly influenced by the design of the magnetic path inside the ETA cores. The ETA chain is operated using a “Follow the Leader” control. Therefore, very fast calculation methods are necessary to evaluate power-on-durations and subsequently influence the tilting process itself. In this paper, the physical effects while operating are analyzed and the necessary calculation methods are elaborated. Since very high currents are applied for tilting, the electric network calculation includes a thermal model to consider the thermally driven asymmetric increase of resistivity as well. The analysis of the operational characteristic of the ETA is the basis of the time-efficient combined calculation method. Using this combined calculation, a complete tilting process of one or more ETA can be calculated in advance considering the chain configuration and external forces. Using this method, optimized power-on-durations can be evaluated, for which the tilting process itself is successful and no unintended impulsive forces are applied to the chain. The validation with measurements has proven the accuracy of the initial model (without parameter fitting) to a deviation of 15 % at most with a very small calculation time effort within seconds.
- 14 June 2019
- Published by Springer Nature
- p. 1701-1710
Resolution of Functional Redundancy for 3T2R Robot Tasks using Two Sets of Reciprocal Euler Angles
- 14 June 2019
- Published by Springer Nature
- p. 1701-1710
Resolution of Functional Redundancy for 3T2R Robot Tasks using Two Sets of Reciprocal Euler Angles
- 14 June 2019
- Published by Springer Nature
- p. 1949-1958
Exploiting Dynamics Parameter Linearity for Design Optimization in Combined Structural and Dimensional Robot Synthesis
- 14 June 2019
- Published by Springer Nature
- p. 1949-1958
Exploiting Dynamics Parameter Linearity for Design Optimization in Combined Structural and Dimensional Robot Synthesis
- 3 May 2019
- Published by Springer Nature
- p. 168-177
Potential of Energy Storage Systems for Industrial Robots
- 3 May 2019
- Published by Springer Nature
- p. 168-177
Potential of Energy Storage Systems for Industrial Robots
- 3 May 2019
- Published by Springer Nature
- p. 217-226
Optimization of a P/PI Cascade Motion Controller for a 3-DOF Delta Robot
- 3 May 2019
- Published by Springer Nature
- p. 217-226
Optimization of a P/PI Cascade Motion Controller for a 3-DOF Delta Robot