Bartosz Firlik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bartosz Firlik has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Tomasz Staśkiewicz
Institute of Transport, Poznan University of Technology, Poznan, Poland
4 shared publications Andrzej Chudzikiewicz
Warsaw University of Technology
1 shared publicationBartosz Czechyra
Poznan University of Technology
1 shared publication- Bartosz Łuczak
Institute of Structural Analysis, Poznan University of Technology, Piotrowo 5, 60-965 Poznań, Poland
1 shared publication Bogdan Sowinski
Warsaw University of Technology
1 shared publicationIvo Haladin
University of Zagreb
1 shared publication
Latest Publications
- 12 November 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
A comparative study of structural vibration transfer in low-floor tramway vehicles
In contrast to more standardized DMU/EMU systems, trams exhibit significantly greater design variability, requiring type-specific and occasionally side-dependent calibration of structural vibration transfer paths. Therefore, determining the structural and dynamic characteristics of various tram vehicles is essential for reliable vehicle-based vibration monitoring. This study compares structural vibration transfer paths in two low-floor tram bogie designs: the Solaris Tramino S105p with conventional wheelsets and the Končar TMK 2200 with independently mounted resilient wheels. Hammer impact tests were performed on mounted and free-standing configurations to determine Frequency response functions (FRFs) between excitation near the wheel–rail contact region and responses at the axle-box or bogie frame. The two tram designs showed similar resonance groups, but local FRF amplitudes differed by up to 10–20 dB. The TMK 2200 also exhibited clear left–right asymmetry, while cross-wheel-pair and cross-bogie transfer was strongest below about 250 Hz. The results provide a structural basis for future vehicle-based rail roughness and corrugation monitoring, although quantitative corrugation identification will require validation under operating conditions and inclusion of wheel–rail contact, track dynamics, vehicle speed and multiple-wheel excitation.
- 12 November 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
A comparative study of structural vibration transfer in low-floor tramway vehicles
In contrast to more standardized DMU/EMU systems, trams exhibit significantly greater design variability, requiring type-specific and occasionally side-dependent calibration of structural vibration transfer paths. Therefore, determining the structural and dynamic characteristics of various tram vehicles is essential for reliable vehicle-based vibration monitoring. This study compares structural vibration transfer paths in two low-floor tram bogie designs: the Solaris Tramino S105p with conventional wheelsets and the Končar TMK 2200 with independently mounted resilient wheels. Hammer impact tests were performed on mounted and free-standing configurations to determine Frequency response functions (FRFs) between excitation near the wheel–rail contact region and responses at the axle-box or bogie frame. The two tram designs showed similar resonance groups, but local FRF amplitudes differed by up to 10–20 dB. The TMK 2200 also exhibited clear left–right asymmetry, while cross-wheel-pair and cross-bogie transfer was strongest below about 250 Hz. The results provide a structural basis for future vehicle-based rail roughness and corrugation monitoring, although quantitative corrugation identification will require validation under operating conditions and inclusion of wheel–rail contact, track dynamics, vehicle speed and multiple-wheel excitation.
- Open Access
- 6 October 2026
- Published by Politechnika Warszawska - Warsaw University of Technology in Archives of Transport
- Vol. 78 (2) , 9-24
Functional and operational analysis of the use of multi-drive railway multiple units on metropolitan railway lines
In metropolitan and, partially, long-distance traffic, we are now seeing an increased use of multiple units characterised by the utilisation of the passenger area that is optimal in terms of interior space. The propulsion systems used in them utilise various forms of supplied energy. Technological development in the field of multi-drive systems for rolling stock offers an increasing diversity of design solutions. Among railway operators and carriers when purchasing rolling stock, this generates the problem of choosing the right type of multiple unit among the numerous types offered by manufacturers. The main purpose of the article is to analyse and evaluate railway multiple units, both classic, diesel-powered and multi-drive ones. Technical, economic, environmental, operational and functional parameters were used as comparison criteria. Modern three-unit trainsets in service in Europe were analysed. On the basis of a multivariate comparative analysis, selected types of multi-drive multiple units were evaluated in terms of their selection for mixed traffic on partially electrified and non-electrified lines. The analysis made it possible not only to evaluate the types of multiple units offered by manufacturers today but also provides a valuable tool in the decision-making process of selecting the optimal rolling stock for metropolitan railways.
- 6 October 2026
- Published by Politechnika Warszawska - Warsaw University of Technology in Archives of Transport
- Vol. 78 (2) , 9-24
Open AccessFunctional and operational analysis of the use of multi-drive railway multiple units on metropolitan railway lines
In metropolitan and, partially, long-distance traffic, we are now seeing an increased use of multiple units characterised by the utilisation of the passenger area that is optimal in terms of interior space. The propulsion systems used in them utilise various forms of supplied energy. Technological development in the field of multi-drive systems for rolling stock offers an increasing diversity of design solutions. Among railway operators and carriers when purchasing rolling stock, this generates the problem of choosing the right type of multiple unit among the numerous types offered by manufacturers. The main purpose of the article is to analyse and evaluate railway multiple units, both classic, diesel-powered and multi-drive ones. Technical, economic, environmental, operational and functional parameters were used as comparison criteria. Modern three-unit trainsets in service in Europe were analysed. On the basis of a multivariate comparative analysis, selected types of multi-drive multiple units were evaluated in terms of their selection for mixed traffic on partially electrified and non-electrified lines. The analysis made it possible not only to evaluate the types of multiple units offered by manufacturers today but also provides a valuable tool in the decision-making process of selecting the optimal rolling stock for metropolitan railways.
- 30 November 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 239 (2) , 165-175
Shaping light rail vehicle wheel profile in terms of wear and ride safety
This paper presents relationships between tram wheel profile geometry and ride safety and wear factors in a model based approach. In order to properly formulate the assumptions for the wheel profile geometry, the influence of selected parameters of the tram wheel profile (number of contact points, clearance between the wheel and the rail, flange inclination) on the dynamic interaction with the rail was determined. Referring to the current state of tram operation conditions in Polish cities, as well as the available scientific literature, the existing, incorrectly selected wheel-rail pairs were also identified in terms of unfavourable placement of contact points, similarity of profile shapes and clearance between the wheel and rail. The interdependencies presented in this work complement the knowledge in the field of cooperation of the tram wheel with the rail, as well as shaping the wheel profile, which is particularly valuable due to the limited number of scientific studies on this subject so far.
- 30 November 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 239 (2) , 165-175
Shaping light rail vehicle wheel profile in terms of wear and ride safety
This paper presents relationships between tram wheel profile geometry and ride safety and wear factors in a model based approach. In order to properly formulate the assumptions for the wheel profile geometry, the influence of selected parameters of the tram wheel profile (number of contact points, clearance between the wheel and the rail, flange inclination) on the dynamic interaction with the rail was determined. Referring to the current state of tram operation conditions in Polish cities, as well as the available scientific literature, the existing, incorrectly selected wheel-rail pairs were also identified in terms of unfavourable placement of contact points, similarity of profile shapes and clearance between the wheel and rail. The interdependencies presented in this work complement the knowledge in the field of cooperation of the tram wheel with the rail, as well as shaping the wheel profile, which is particularly valuable due to the limited number of scientific studies on this subject so far.
- 2 February 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 237 (9) , 1195-1204
Thermal imaging of the wheel-rail interface
The paper presents the use of a new method of imaging of the wheel-rail interface wear adopting thermal imaging techniques. Based on the heat generated at the point of contact, coming from the friction and strain of the mating materials, it is possible to identify the type and location of the wheel-rail interface. This work presents the usability of the method with reference to the typical conditions of operation of light rail vehicles (small-radius curves – from 22 m, wheel diameter around 0.6 m, lower standard of track maintenance than in the case of regular railways, use of shallow-grooved frogs, etc.). Thermal imaging presents a big potential in terms of monitoring the wheel-rail interaction and can also be used to identify flange climbing, rolling noise generation or longitudinal creepage during traction or braking.
- 2 February 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 237 (9) , 1195-1204
Thermal imaging of the wheel-rail interface
The paper presents the use of a new method of imaging of the wheel-rail interface wear adopting thermal imaging techniques. Based on the heat generated at the point of contact, coming from the friction and strain of the mating materials, it is possible to identify the type and location of the wheel-rail interface. This work presents the usability of the method with reference to the typical conditions of operation of light rail vehicles (small-radius curves – from 22 m, wheel diameter around 0.6 m, lower standard of track maintenance than in the case of regular railways, use of shallow-grooved frogs, etc.). Thermal imaging presents a big potential in terms of monitoring the wheel-rail interaction and can also be used to identify flange climbing, rolling noise generation or longitudinal creepage during traction or braking.
- 11 February 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 236 (1) , 122-133
Out-of-round tram wheels – Multibody simulation study based on measured wheel rim geometry
The article discusses the influence of out-of-roundness (OOR) type of wheel shape deviations on its interaction with the rail. The analysis was carried out using multibody simulation technique (MBS). Measurements of tram wheel rims and sample models of flat spots were used as input data. It has been observed that the presence of wheel OOR deviations caused a significant increase in vertical impact loads at the interface between the wheel and the rail, which favours rolling contact fatigue formation. Deviations created at the stage of manufacturing the wheel rim (usually while the profile of the rim itself is turned on a lathe) were amplified by increasing amplitudes and were also visible during the measurement of worn rims, thus creating inequalities with dominant amplitudes. Flat spots present on the rolling surfaces of the wheels cause cyclic jumps of vertical force at the contact point of the wheel and the rail, with maximum values depending on the depth and radius of the rounded edges of the flat spot, and thus subject to change in subsequent stages of the flat spot development. Taking into account the observations made, preventive measures have been proposed against the development of OOR deviations in tram wheels, the origin of which is primarily in the machining process.
- 11 February 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 236 (1) , 122-133
Out-of-round tram wheels – Multibody simulation study based on measured wheel rim geometry
The article discusses the influence of out-of-roundness (OOR) type of wheel shape deviations on its interaction with the rail. The analysis was carried out using multibody simulation technique (MBS). Measurements of tram wheel rims and sample models of flat spots were used as input data. It has been observed that the presence of wheel OOR deviations caused a significant increase in vertical impact loads at the interface between the wheel and the rail, which favours rolling contact fatigue formation. Deviations created at the stage of manufacturing the wheel rim (usually while the profile of the rim itself is turned on a lathe) were amplified by increasing amplitudes and were also visible during the measurement of worn rims, thus creating inequalities with dominant amplitudes. Flat spots present on the rolling surfaces of the wheels cause cyclic jumps of vertical force at the contact point of the wheel and the rail, with maximum values depending on the depth and radius of the rounded edges of the flat spot, and thus subject to change in subsequent stages of the flat spot development. Taking into account the observations made, preventive measures have been proposed against the development of OOR deviations in tram wheels, the origin of which is primarily in the machining process.
- 6 November 2019
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 234 (10) , 1156-1169
Numerical algorithm for predicting wheel flange wear in trams – Validation in a curved track
In tram operations, flange wear is predominant due to the low-radius curves and inappropriate technical conditions of the infrastructure; hence, investigations should be focused on the interaction between the wheel flange and the rail gauge corner. Moreover, the calculation methods based on the Hertzian model (elliptic contact patch) provide less accurate results due to the contact occurrence in the wheel flange region. This paper presents a methodology of a finite element method to predict the tram wheel wear in complex motions. The new procedure is based on the Abaqus software and several other sub-procedures written in Python and Fortran. Multibody simulations were used to determine the wheel–rail alignment. In this method, accuracy was chosen at the expense of the computational effort. The main steps are: preparation of models and ride scenarios, multibody simulation for calculating the wheel–rail alignment for different track scenarios and multiple runs of finite element method analysis to determine the wear magnitude. The proposed methodology presents a good agreement with the measurements and can be considered as guidelines for a proper configuration of the flange-designing experimental setup where the influence of the technical conditions of the infrastructure should be introduced adequately.
- 6 November 2019
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 234 (10) , 1156-1169
Numerical algorithm for predicting wheel flange wear in trams – Validation in a curved track
In tram operations, flange wear is predominant due to the low-radius curves and inappropriate technical conditions of the infrastructure; hence, investigations should be focused on the interaction between the wheel flange and the rail gauge corner. Moreover, the calculation methods based on the Hertzian model (elliptic contact patch) provide less accurate results due to the contact occurrence in the wheel flange region. This paper presents a methodology of a finite element method to predict the tram wheel wear in complex motions. The new procedure is based on the Abaqus software and several other sub-procedures written in Python and Fortran. Multibody simulations were used to determine the wheel–rail alignment. In this method, accuracy was chosen at the expense of the computational effort. The main steps are: preparation of models and ride scenarios, multibody simulation for calculating the wheel–rail alignment for different track scenarios and multiple runs of finite element method analysis to determine the wear magnitude. The proposed methodology presents a good agreement with the measurements and can be considered as guidelines for a proper configuration of the flange-designing experimental setup where the influence of the technical conditions of the infrastructure should be introduced adequately.
- 6 August 2019
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 234 (7) , 702-708
Monitoring of the technical condition of tracks based on machine learning
This paper presents the concept of a simple system for the identification of the technical condition of tracks based on a trained learning system in the form of three independent neural networks. The studies conducted showed that basic measurements based on the root mean square of vibration acceleration allow for monitoring the track condition provided that the rail type has been included in the information system. Also, it is necessary to select data based on the threshold value of the vehicle velocity. In higher velocity ranges (above 40 km/h), it is possible to distinguish technical conditions with a permissible error of 5%. Such selection also enables to ignore the impact of rides through switches and crossings. Technical condition monitoring is also possible at lower ride velocities; however, this comes at the cost of reduced accuracy of the analysis.
- 6 August 2019
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 234 (7) , 702-708
Monitoring of the technical condition of tracks based on machine learning
This paper presents the concept of a simple system for the identification of the technical condition of tracks based on a trained learning system in the form of three independent neural networks. The studies conducted showed that basic measurements based on the root mean square of vibration acceleration allow for monitoring the track condition provided that the rail type has been included in the information system. Also, it is necessary to select data based on the threshold value of the vehicle velocity. In higher velocity ranges (above 40 km/h), it is possible to distinguish technical conditions with a permissible error of 5%. Such selection also enables to ignore the impact of rides through switches and crossings. Technical condition monitoring is also possible at lower ride velocities; however, this comes at the cost of reduced accuracy of the analysis.
- 10 March 2016
- Published by Civil-Comp, Ltd.
- Vol. 110
Wheel-Rail Interaction Analysis for the Development of a New Tram Wheel Profile
- 10 March 2016
- Published by Civil-Comp, Ltd.
- Vol. 110
Wheel-Rail Interaction Analysis for the Development of a New Tram Wheel Profile
- 1 July 2012
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 518, 409-417
Vibration-Based Symptoms in Condition Monitoring of a Light Rail Vehicle
Light rail systems have now their great return in many European cities carrying an increasing number of people every year. This increasing trend requires suitable operation and maintenance standards for both vehicle and track. Furthermore, in order to make a public transport competitive to private transport, its very important to increase safety and ride comfort for passengers. The aim of the presented work was to determine the suitable vibration-based symptoms for the identification of a light rail vehicle technical state, as well as the development of appropriate methodology to use the information contained therein. Both simulation and experimental phase are described. The present analysis is focused mainly on the suspension state monitoring, but some others failures were also considered.
- 1 July 2012
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 518, 409-417
Vibration-Based Symptoms in Condition Monitoring of a Light Rail Vehicle
Light rail systems have now their great return in many European cities carrying an increasing number of people every year. This increasing trend requires suitable operation and maintenance standards for both vehicle and track. Furthermore, in order to make a public transport competitive to private transport, its very important to increase safety and ride comfort for passengers. The aim of the presented work was to determine the suitable vibration-based symptoms for the identification of a light rail vehicle technical state, as well as the development of appropriate methodology to use the information contained therein. Both simulation and experimental phase are described. The present analysis is focused mainly on the suspension state monitoring, but some others failures were also considered.
- 1 July 2012
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 518, 66-75
Condition Monitoring System for Light Rail Vehicle and Track
Condition monitoring and fault detection systems are becoming increasingly important in rail vehicles maintenance and operation, ensuring safety and reliability improvement. Light rail systems are not the main target for this trend, because of low operational speed and lower safety factors. Nevertheless public transport operators begin to pay a closer attention to the technical state monitoring of vehicle and track, in order to reduce maintenance cost and increase safety and ride comfort for passengers, which is an important challenge for public transport competitiveness in XXI century. The paper describes the main concept of the innovative on-board condition monitoring system for light rail vehicle and track. Functional requirements, assumptions and procedures are described, as well as the on-board data acquisition unit with necessary transducers, which number, function and technical parameters were optimized during the research phase of the project. The prototype of the presented system is now being tested in normal operating conditions.
- 1 July 2012
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 518, 66-75
Condition Monitoring System for Light Rail Vehicle and Track
Condition monitoring and fault detection systems are becoming increasingly important in rail vehicles maintenance and operation, ensuring safety and reliability improvement. Light rail systems are not the main target for this trend, because of low operational speed and lower safety factors. Nevertheless public transport operators begin to pay a closer attention to the technical state monitoring of vehicle and track, in order to reduce maintenance cost and increase safety and ride comfort for passengers, which is an important challenge for public transport competitiveness in XXI century. The paper describes the main concept of the innovative on-board condition monitoring system for light rail vehicle and track. Functional requirements, assumptions and procedures are described, as well as the on-board data acquisition unit with necessary transducers, which number, function and technical parameters were optimized during the research phase of the project. The prototype of the presented system is now being tested in normal operating conditions.