Luis Felix
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Luis Felix has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Afzal Suleman
Department of Mechanical Engineering, University of Victoria, Victoria, BC V8P 5C2, Canada
4 shared publications - Gonçalo Cruz
Portuguese Air Force Research Center, 2715-311 Sintra, Portugal
4 shared publications - João Vieira Caetano
Section of Control and Simulation, Faculty of Aerospace Engineering, Delft University of Technology, The Netherlands
3 shared publications - Diogo Silva
Portuguese Air Force Academy Research Centre
2 shared publications - Vasco Coelho
Portuguese Air Force Academy Research Centre
2 shared publications A. L. C. Santos
Portuguese Air Force Academy Research Center, Sintra, Portugal
1 shared publication
Latest Publications
- 27 April 2024
- Published by Springer Nature
- p. 269-281
ISR Missions in Maritime Environment Using UAS - Contributions of the Portuguese Air Force Academy Research Centre
- 27 April 2024
- Published by Springer Nature
- p. 269-281
ISR Missions in Maritime Environment Using UAS - Contributions of the Portuguese Air Force Academy Research Centre
- 2 August 2023
- Published by Springer Nature
- p. 183-193
Towards the Automation of Wildfire Monitoring with Aerial Vehicles: The FIREFRONT Project
- 2 August 2023
- Published by Springer Nature
- p. 183-193
Towards the Automation of Wildfire Monitoring with Aerial Vehicles: The FIREFRONT Project
- Open Access
Neutron and Gamma-Ray Detection System Coupled to a Multirotor for Screening of Shipping Container Cargo
In order to detect special nuclear materials and other radioactive materials in Security and Defense scenarios, normally, a combination of neutron and gamma-ray detection systems is used. In particular, to avoid illicit traffic of special nuclear materials and radioactive sources/materials, radiation portal monitors are placed at seaports to inspect shipping-container cargo. Despite their large volume (high efficiency), these detection systems are expensive, and therefore only a fraction of these containers are inspected. In this work, a novel mobile radiation detection system is presented, based on an EJ-200 plastic scintillator for the detection of gamma rays and beta particles, and a neutron detector EJ-426HD plastic scintillator (with 6Li) embedded in a compact and modular moderator. The use of silicon photomultipliers in both detectors presented advantages such as lightweight, compactness, and low power consumption. The developed detection system was integrated in a highly maneuverable multirotor. Monte Carlo simulations were validated by laboratory measurements and field tests were performed using real gamma-ray and neutron sources. The detection and localization within one meter was achieved using a maximum likelihood estimation algorithm for 137Cs sources (4 MBq), as well as the detection of 241Am–beryllium (1.45 GBq) source placed inside the shipping container.
Open AccessNeutron and Gamma-Ray Detection System Coupled to a Multirotor for Screening of Shipping Container Cargo
In order to detect special nuclear materials and other radioactive materials in Security and Defense scenarios, normally, a combination of neutron and gamma-ray detection systems is used. In particular, to avoid illicit traffic of special nuclear materials and radioactive sources/materials, radiation portal monitors are placed at seaports to inspect shipping-container cargo. Despite their large volume (high efficiency), these detection systems are expensive, and therefore only a fraction of these containers are inspected. In this work, a novel mobile radiation detection system is presented, based on an EJ-200 plastic scintillator for the detection of gamma rays and beta particles, and a neutron detector EJ-426HD plastic scintillator (with 6Li) embedded in a compact and modular moderator. The use of silicon photomultipliers in both detectors presented advantages such as lightweight, compactness, and low power consumption. The developed detection system was integrated in a highly maneuverable multirotor. Monte Carlo simulations were validated by laboratory measurements and field tests were performed using real gamma-ray and neutron sources. The detection and localization within one meter was achieved using a maximum likelihood estimation algorithm for 137Cs sources (4 MBq), as well as the detection of 241Am–beryllium (1.45 GBq) source placed inside the shipping container.
- 7 August 2019
- Published by Taylor & Francis in Engineering Optimization
- Vol. 52 (7) , 1119-1135
Topology optimization of the internal structure of an aircraft wing subjected to self-weight load
A topology optimization design framework for structures including self-weight loads is presented. The proposed methodology applied to lifting structures aims to eliminate numerical instabilities due to the weight load while improving the overall solution quality. In this model, a power-law function is used to update the element density in the determination of the self-weight. The algorithm is tested and verified for a two-dimensional benchmark problem subjected to self-weight loads and a point force. Results show that the proposed method improves the discreteness of the design of structures subjected to lifting surface loads. Following the verification step, the proposed method is used to optimize the internal structure of an aircraft wing. The aerodynamic load is computed assuming a rigid wing body, and the loading condition is completed with the structure self-weight. Results show that, in this particular example, the self-weight load has a negligible influence on the optimal design.
- 7 August 2019
- Published by Taylor & Francis in Engineering Optimization
- Vol. 52 (7) , 1119-1135
Topology optimization of the internal structure of an aircraft wing subjected to self-weight load
A topology optimization design framework for structures including self-weight loads is presented. The proposed methodology applied to lifting structures aims to eliminate numerical instabilities due to the weight load while improving the overall solution quality. In this model, a power-law function is used to update the element density in the determination of the self-weight. The algorithm is tested and verified for a two-dimensional benchmark problem subjected to self-weight loads and a point force. Results show that the proposed method improves the discreteness of the design of structures subjected to lifting surface loads. Following the verification step, the proposed method is used to optimize the internal structure of an aircraft wing. The aerodynamic load is computed assuming a rigid wing body, and the loading condition is completed with the structure self-weight. Results show that, in this particular example, the self-weight load has a negligible influence on the optimal design.
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1126-1135
Design of a Class I Unmanned Aircraft for Maritime Surveillance
The current paper’s objective is to present the methodology used in the design of a class I unmanned aircraft (UA), intended for maritime surveillance, atmospheric pollution monitoring and search and rescue (SAR) missions. Its development encompasses conceptual and preliminary design, focusing on the integration of systems, performance, aerodynamics, stability, propulsion and composite structural design. Mission requirements are set to comply with the European Maritime Safety Agency’s specifications. The approach to conceptual design follows a methodology in which the airplane is conceived in a step-by-step, iterative fashion, making use of empirical data and numerical information. In preliminary design, computational fluid dynamics (CFD) is employed in order to increase the level of accuracy and refine the design. Subsequently, the air frame design is performed through computed aided design (CAD) modelling, endorsed by a numerical stress analysis via a finite element analysis (FEA). As the project’s output, a class I unmanned aircraft capable of not only meeting, but also surpassing the demanded mission requirements, is presented.
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1126-1135
Design of a Class I Unmanned Aircraft for Maritime Surveillance
The current paper’s objective is to present the methodology used in the design of a class I unmanned aircraft (UA), intended for maritime surveillance, atmospheric pollution monitoring and search and rescue (SAR) missions. Its development encompasses conceptual and preliminary design, focusing on the integration of systems, performance, aerodynamics, stability, propulsion and composite structural design. Mission requirements are set to comply with the European Maritime Safety Agency’s specifications. The approach to conceptual design follows a methodology in which the airplane is conceived in a step-by-step, iterative fashion, making use of empirical data and numerical information. In preliminary design, computational fluid dynamics (CFD) is employed in order to increase the level of accuracy and refine the design. Subsequently, the air frame design is performed through computed aided design (CAD) modelling, endorsed by a numerical stress analysis via a finite element analysis (FEA). As the project’s output, a class I unmanned aircraft capable of not only meeting, but also surpassing the demanded mission requirements, is presented.
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
C-band SAR radar trials using UAV platform: Experimental results of SAR system integration on a UAV carrier
In this paper the experimental results of C-band synthetic aperture radar (SAR) system integration on an unmanned aerial vehicle (UAV) are shown. The goal of the presented trials was to check the capabilities and limitations of the SAR system in UAV applications. The trials were conducted with a UAV system developed and operated by the Portuguese Air Force Academy (PAFA) using a compact SAR system, named SARENKA, developed by the Warsaw University of Technology (WUT).
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
C-band SAR radar trials using UAV platform: Experimental results of SAR system integration on a UAV carrier
In this paper the experimental results of C-band synthetic aperture radar (SAR) system integration on an unmanned aerial vehicle (UAV) are shown. The goal of the presented trials was to check the capabilities and limitations of the SAR system in UAV applications. The trials were conducted with a UAV system developed and operated by the Portuguese Air Force Academy (PAFA) using a compact SAR system, named SARENKA, developed by the Warsaw University of Technology (WUT).