Daniel Ourinson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Daniel Ourinson has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
Florian Clement
Fraunhofer Institute for Solar Energy Systems ISE, Freiburg, Germany
4 shared publicationsGernot Emanuel
Fraunhofer Institute for Solar Energy Systems ISE, Freiburg, Germany
3 shared publications- Gernot Emanuel
Fraunhofer Institute for Solar Energy Systems ISE 79110 Freiburg Germany
3 shared publications Gunnar Dammaß
InfraTec GmbH
3 shared publications- Stefan Glunz
Fraunhofer Institute for Solar Energy Systems ISE Freiburg Germany
3 shared publications - Florian Clement
Fraunhofer Institute for Solar Energy Systems (ISE), Heidenhofstr. 2, D-79110 Freiburg, Germany
2 shared publications
Latest Publications
- Open Access
Microstructure Analysis of Current‐Fired Contacts on TOPCon Layers
We report on the analysis of the microstructure of a current‐fired contact formed by screen printing, drying, and sintering of a silver paste and subsequent laser‐enhanced contact optimization (LECO) for silicon solar cells with tunnel‐oxide passivated contacts (TOPCon) on the TOPCon side. The analysis is based on scanning electron microscopy and energy dispersive X‐ray spectroscopy. We show that a new phase is formed during LECO at individual points of the interface between the contact finger and the polycrystalline silicon layer consisting of silver and silicon. The altered material combination is confined to the metal and the polycrystalline layer only and does not penetrate through the tunnel oxide into the silicon wafer. We conclude that the mechanism for the contact formation on the TOPCon stack is very similar to the one reported for the front contact of passivated emitter and rear cells.
Open AccessMicrostructure Analysis of Current‐Fired Contacts on TOPCon Layers
We report on the analysis of the microstructure of a current‐fired contact formed by screen printing, drying, and sintering of a silver paste and subsequent laser‐enhanced contact optimization (LECO) for silicon solar cells with tunnel‐oxide passivated contacts (TOPCon) on the TOPCon side. The analysis is based on scanning electron microscopy and energy dispersive X‐ray spectroscopy. We show that a new phase is formed during LECO at individual points of the interface between the contact finger and the polycrystalline silicon layer consisting of silver and silicon. The altered material combination is confined to the metal and the polycrystalline layer only and does not penetrate through the tunnel oxide into the silicon wafer. We conclude that the mechanism for the contact formation on the TOPCon stack is very similar to the one reported for the front contact of passivated emitter and rear cells.
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2826 (1) , 020006
Faster firing processes up to 20 m/min belt velocity
This work successfully demonstrates fast firing processes with a technical throughput of 13204 cells/h for M2- sized solar cells (assumption of a double-lane fu
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2826 (1) , 020006
Open AccessFaster firing processes up to 20 m/min belt velocity
This work successfully demonstrates fast firing processes with a technical throughput of 13204 cells/h for M2- sized solar cells (assumption of a double-lane fu
- Open Access
- 6 July 2022
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 16 (8)
Short Drying Processes for Silicon Solar Cells
Herein, very short drying processes for the screen‐printed electrodes of passivated emitter and rear solar cells (PERC) are successfully demonstrated. The short drying processes are conducted in an in‐line heating system with vertical‐cavity surface‐emitting lasers (VCSEL) as its heat source, being a compact alternative to the conventional heating chamber. While the heating time of the conventional industrial drying process is believed to be about 20 s (to the best of the authors’ knowledge), the VCSEL system allows a significant reduction down to 0.15 s while maintaining a similar power conversion efficiency and contact adhesion quality.
- 6 July 2022
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 16 (8)
Open AccessShort Drying Processes for Silicon Solar Cells
Herein, very short drying processes for the screen‐printed electrodes of passivated emitter and rear solar cells (PERC) are successfully demonstrated. The short drying processes are conducted in an in‐line heating system with vertical‐cavity surface‐emitting lasers (VCSEL) as its heat source, being a compact alternative to the conventional heating chamber. While the heating time of the conventional industrial drying process is believed to be about 20 s (to the best of the authors’ knowledge), the VCSEL system allows a significant reduction down to 0.15 s while maintaining a similar power conversion efficiency and contact adhesion quality.
- 8 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 11 (2) , 282-288
Laser-Powered Co-Firing Process for Highly Efficient Si Solar Cells
This article presents a successful laser-powered co-firing process for highly efficient Si solar cells as a more compact and energy-efficient alternative to the conventional firing process in an infrared (IR) lamp-powered heat chamber. The best cell group reaches with laser firing only 0.1%abs lower cell efficiency compared to the best group with conventional firing, demonstrating the industrial potential of this laser firing technology. Adding the laser enhanced contact optimization (LECO) process after firing improves the cell efficiency for laser firing to the level of conventional firing, demonstrating the potential of the combination of the laser firing and the LECO process.
- 8 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 11 (2) , 282-288
Laser-Powered Co-Firing Process for Highly Efficient Si Solar Cells
This article presents a successful laser-powered co-firing process for highly efficient Si solar cells as a more compact and energy-efficient alternative to the conventional firing process in an infrared (IR) lamp-powered heat chamber. The best cell group reaches with laser firing only 0.1%abs lower cell efficiency compared to the best group with conventional firing, demonstrating the industrial potential of this laser firing technology. Adding the laser enhanced contact optimization (LECO) process after firing improves the cell efficiency for laser firing to the level of conventional firing, demonstrating the potential of the combination of the laser firing and the LECO process.
- 27 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 11 (1) , 174-184
Spatially Resolved Determination of Metallization-Induced Recombination Losses Using Photoluminescence Imaging
Metallization induced recombination losses are one dominant loss mechanism for current industrial solar cells. A precise determination of these losses is important for contacting technology optimization, as well as precise solar cell modeling. Usually, for state-of-the-art approaches to determine j $_{0,\text{met}}$ , it is assumed that the samples itself exhibit spatially uniform properties (e.g., carrier lifetime or sheet resistance) or that the used reference samples are identical to the metallized samples. Finally, in most cases, only one global j $_{0,\text{met}}$ -value for the entire sample is given, neglecting possible spatial inhomogeneities. In this article, we mostly eliminate the necessity for the assumptions of perfect sample homogeneity by means of an interpolation scheme of the photoluminescence (PL) signal. Thereby, we can predict the PL signal of a virtually nonmetallized test field with a relative standard deviation of about σ ≈ 0.7%. Additionally, we determine j $_{0,\text{met}}$ for specific test fields at different positions on the sample and correlate the results to the local emitter sheet resistance R $_{\text{sh}}$ , the local peak firing temperature of the sample during the fast firing process T $_{\text{peak}}$ , and the test field finger spacing d. For our samples, a reduction of d from d = 1000 μm to d = 200 μm leads to a reduction of j $_{0,\text{met}}$ by up to 18%. This strong effect is physically unexpected and so far not considered by the state-of-the-art approach, frequently performed in the photovoltaic community. Further, we perform a sensitivity and error analysis which reveals that we are able to determine j $_{0,\text{met}}$ within an estimated accuracy between 15% and 18%.- 27 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 11 (1) , 174-184
Spatially Resolved Determination of Metallization-Induced Recombination Losses Using Photoluminescence Imaging
Metallization induced recombination losses are one dominant loss mechanism for current industrial solar cells. A precise determination of these losses is important for contacting technology optimization, as well as precise solar cell modeling. Usually, for state-of-the-art approaches to determine j $_{0,\text{met}}$ , it is assumed that the samples itself exhibit spatially uniform properties (e.g., carrier lifetime or sheet resistance) or that the used reference samples are identical to the metallized samples. Finally, in most cases, only one global j $_{0,\text{met}}$ -value for the entire sample is given, neglecting possible spatial inhomogeneities. In this article, we mostly eliminate the necessity for the assumptions of perfect sample homogeneity by means of an interpolation scheme of the photoluminescence (PL) signal. Thereby, we can predict the PL signal of a virtually nonmetallized test field with a relative standard deviation of about σ ≈ 0.7%. Additionally, we determine j $_{0,\text{met}}$ for specific test fields at different positions on the sample and correlate the results to the local emitter sheet resistance R $_{\text{sh}}$ , the local peak firing temperature of the sample during the fast firing process T $_{\text{peak}}$ , and the test field finger spacing d. For our samples, a reduction of d from d = 1000 μm to d = 200 μm leads to a reduction of j $_{0,\text{met}}$ by up to 18%. This strong effect is physically unexpected and so far not considered by the state-of-the-art approach, frequently performed in the photovoltaic community. Further, we perform a sensitivity and error analysis which reveals that we are able to determine j $_{0,\text{met}}$ within an estimated accuracy between 15% and 18%.- 30 May 2020
- Published by MyJove Corporation in Journal of Visualized Experiments
- No. 159,p. e60963
In Situ Surface Temperature Measurement in a Conveyor Belt Furnace via Inline Infrared Thermography
Measuring the surface temperature of objects that are processed in conveyor belt furnaces is an important tool in process control and quality assurance. Currently, the surface temperature of objects processed in conveyor belt furnaces is typically measured via thermocouples. However, infrared (IR) thermography presents multiple advantages compared to thermocouple measurements, as it is a contactless, real-time, and spatially resolved method. Here, as a representative proof-of-concept example, an inline thermography system is successfully installed into an IR lamp powered solar firing furnace, which is used for the contact firing process of industrial Si solar cells. This protocol describes how to install an IR camera into a conveyor belt furnace, conduct a customer correction of a factory calibrated IR camera, and perform the evaluation of spatial surface temperature distribution on a target object.
- 30 May 2020
- Published by MyJove Corporation in Journal of Visualized Experiments
- No. 159,p. e60963
In Situ Surface Temperature Measurement in a Conveyor Belt Furnace via Inline Infrared Thermography
Measuring the surface temperature of objects that are processed in conveyor belt furnaces is an important tool in process control and quality assurance. Currently, the surface temperature of objects processed in conveyor belt furnaces is typically measured via thermocouples. However, infrared (IR) thermography presents multiple advantages compared to thermocouple measurements, as it is a contactless, real-time, and spatially resolved method. Here, as a representative proof-of-concept example, an inline thermography system is successfully installed into an IR lamp powered solar firing furnace, which is used for the contact firing process of industrial Si solar cells. This protocol describes how to install an IR camera into a conveyor belt furnace, conduct a customer correction of a factory calibrated IR camera, and perform the evaluation of spatial surface temperature distribution on a target object.
- 30 May 2020
- Published by MyJove Corporation in Journal of Visualized Experiments
- No. 159
In Situ Surface Temperature Measurement in a Conveyor Belt Furnace via Inline Infrared Thermography
This protocol describes how to install an infrared camera into a conveyor belt furnace, conduct a customer correction of a factory calibrated IR camera, and evaluate the spatial surface temperature distribution of an object of interest. The example objects are industrial silicon solar cells.
- 30 May 2020
- Published by MyJove Corporation in Journal of Visualized Experiments
- No. 159
In Situ Surface Temperature Measurement in a Conveyor Belt Furnace via Inline Infrared Thermography
This protocol describes how to install an infrared camera into a conveyor belt furnace, conduct a customer correction of a factory calibrated IR camera, and evaluate the spatial surface temperature distribution of an object of interest. The example objects are industrial silicon solar cells.
- 16 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 10 (6) , 1523-1531
Optimization of Al Fire-Through Contacts for AlOX–SiNX Rear Passivated Bifacial p-PERC
We present optimizations of rear Al fire-through (FT) contacts for bifacial p-type passivated emitter and rear (AlO $_{\rm X}$ –SiN $_{\rm X}$ ) cells. This approach allows omitting the laser contact opening step. Prior to this work, high FT lateral resistance due to its glass frit, and high rear surface recombination due to large passivation damage and back surface field layer (BSF) abscence, decreased the cell performance for cells with Al FT contacts. In this work, a proper BSF has been achieved by adapting the firing process and by printing multilayer fingers. Achievement of increased BSF thickness and reduced rear contact area—by means of dashing or finger narrowing by dispensing (down to 70 μm)—seems to close the gap to the non-FT (NFT) reference level in terms of contact recombination. This is indicated by reaching similar open-circuit voltages for rear-side-only fired (front side plated) cells. For cofired cells, open-circuit voltages were 6 mV below NFT level, stemming most likely from an overfired front side contact due to firing process adaptations. Multilayer printing allows for a decrease of the lateral resistance of the less conductive FT grid due to an increase of the finger cross-sectional area. For best rear-side-only fired FT cells, reduced recombination and resistance closed the efficiency (η) gap to the NFT reference. For the best cofired FT cells, η $\approx$ 21.3% and bifacial power output density of $P_{\beta\_{\rm OUT}}$ $\approx$ 22.8 mW/cm2 is achieved compared to η $\approx$ 21.5% and $P_{\beta\_{\rm OUT}}$ $\approx$ 23.1 mW/cm2 for NFT. The remaining $P_{\beta\_{\rm OUT}}$ gap has the potential to be reduced by the means of mitigating front side contact overfiring by matching thermal tolerance of the front side paste, and reducing rear side finger resistivity by paste optimization.- 16 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 10 (6) , 1523-1531
Optimization of Al Fire-Through Contacts for AlOX–SiNX Rear Passivated Bifacial p-PERC
We present optimizations of rear Al fire-through (FT) contacts for bifacial p-type passivated emitter and rear (AlO $_{\rm X}$ –SiN $_{\rm X}$ ) cells. This approach allows omitting the laser contact opening step. Prior to this work, high FT lateral resistance due to its glass frit, and high rear surface recombination due to large passivation damage and back surface field layer (BSF) abscence, decreased the cell performance for cells with Al FT contacts. In this work, a proper BSF has been achieved by adapting the firing process and by printing multilayer fingers. Achievement of increased BSF thickness and reduced rear contact area—by means of dashing or finger narrowing by dispensing (down to 70 μm)—seems to close the gap to the non-FT (NFT) reference level in terms of contact recombination. This is indicated by reaching similar open-circuit voltages for rear-side-only fired (front side plated) cells. For cofired cells, open-circuit voltages were 6 mV below NFT level, stemming most likely from an overfired front side contact due to firing process adaptations. Multilayer printing allows for a decrease of the lateral resistance of the less conductive FT grid due to an increase of the finger cross-sectional area. For best rear-side-only fired FT cells, reduced recombination and resistance closed the efficiency (η) gap to the NFT reference. For the best cofired FT cells, η $\approx$ 21.3% and bifacial power output density of $P_{\beta\_{\rm OUT}}$ $\approx$ 22.8 mW/cm2 is achieved compared to η $\approx$ 21.5% and $P_{\beta\_{\rm OUT}}$ $\approx$ 23.1 mW/cm2 for NFT. The remaining $P_{\beta\_{\rm OUT}}$ gap has the potential to be reduced by the means of mitigating front side contact overfiring by matching thermal tolerance of the front side paste, and reducing rear side finger resistivity by paste optimization.- Open Access
- 26 July 2019
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 13 (10) , 1900270
In Situ Solar Wafer Temperature Measurement during Firing Process via Inline IR Thermography
Herein, an inline IR thermography system as an innovative application for real‐time contactless temperature measurement of wafers—both metallized and nonmetallized—during the firing process is successfully realized in an industrial firing furnace as proof of concept and example for a thermography system in a conveyor furnace. As observed by the new system, thermocouples (TCs) seem to measure lower temperature on wafers—especially in combination with TC frames—than wafers exhibit at standard firing conditions (here up to ΔT ≈ 40 K). Furthermore, highly resolved spatial temperature distribution can be successfully measured on the wafer.
- 26 July 2019
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 13 (10) , 1900270
Open AccessIn Situ Solar Wafer Temperature Measurement during Firing Process via Inline IR Thermography
Herein, an inline IR thermography system as an innovative application for real‐time contactless temperature measurement of wafers—both metallized and nonmetallized—during the firing process is successfully realized in an industrial firing furnace as proof of concept and example for a thermography system in a conveyor furnace. As observed by the new system, thermocouples (TCs) seem to measure lower temperature on wafers—especially in combination with TC frames—than wafers exhibit at standard firing conditions (here up to ΔT ≈ 40 K). Furthermore, highly resolved spatial temperature distribution can be successfully measured on the wafer.