Hyun Il Park
Hyun Il Park has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Borinara Park
Department of Technology , Illinois State University , Normal , IL , USA
2 shared publicationsSeung Rae Lee
Department of Civil and Environmental Engineering , Korea Advanced Institute of Science and Technology , Taejon , Korea
2 shared publicationsC. W. Cho
General Manager, Technical Advisory Team, Samsung Engineering and Construction , Seoul, Korea
1 shared publicationChang-Wook Park
Samsung C & T, Seoul, Korea
1 shared publicationDaejin Hwang
Senior Researcher, R&D Team, Technology Division, Samsung Corporation, 4th Floor, Seohyun Building, 270-1 Seohyun-Dong Bundang-Gu, Sungnam-Si, Gyonggi-Do, Korea
1 shared publicationJ. H. Shin
Institute of Construction Technology, Engineering and Construction Group, Samsung C + T Corporation , Seoul, Korea
1 shared publication
Latest Publications
- 2 October 2014
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 35 (1) , 1-7
Evaluation of the applicability of pier local scour formulae using laboratory and field data
The reliable estimation of the local scour depth at a bridge pier is essential for proper design and maintenance of bridge piers. Most local scour formulae have been developed based on the results of laboratory experiments. The formulae based on laboratory data do not often produce reasonable predictions for field piers because laboratory investigations are apt to oversimplify or ignore many of the complexities of the flow fields around the bridge piers. Validation of the formulae is necessary in order to ascertain which of the formulae are able to provide reasonable estimates of the local scour depth. In this study, six commonly cited formulae based on laboratory data or field data were selected for validation using 180 laboratory data sets gathered from the literature and 446 field data sets collected from four countries. The six formulae validated in this paper are the Colorado State University (CSU), Neill, Froehlich, Breuser, Laursen, and simplified Chinese formulae. Comparisons between the predicted and measured depths were performed using scour from the laboratory and field data. An artificial neural network technique was also applied in order to compare the tendencies between the field and laboratory data sets.
- 2 October 2014
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 35 (1) , 1-7
Evaluation of the applicability of pier local scour formulae using laboratory and field data
The reliable estimation of the local scour depth at a bridge pier is essential for proper design and maintenance of bridge piers. Most local scour formulae have been developed based on the results of laboratory experiments. The formulae based on laboratory data do not often produce reasonable predictions for field piers because laboratory investigations are apt to oversimplify or ignore many of the complexities of the flow fields around the bridge piers. Validation of the formulae is necessary in order to ascertain which of the formulae are able to provide reasonable estimates of the local scour depth. In this study, six commonly cited formulae based on laboratory data or field data were selected for validation using 180 laboratory data sets gathered from the literature and 446 field data sets collected from four countries. The six formulae validated in this paper are the Colorado State University (CSU), Neill, Froehlich, Breuser, Laursen, and simplified Chinese formulae. Comparisons between the predicted and measured depths were performed using scour from the laboratory and field data. An artificial neural network technique was also applied in order to compare the tendencies between the field and laboratory data sets.
- 29 June 2011
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 29 (4) , 267-278
Development of Neural Network Model to Estimate the Permeability Coefficient of Soils
The permeability coefficient is a one of the important soil parameters that is essential to geotechnical designs. As the determination of the permeability coefficient from field tests is relatively time-consuming, empirical formulas based on soil parameters can be useful. Over the decades, a number of empirical formulas have been proposed to relate the compressibility to other soil parameters, such as the natural water content, grain size, specific gravity, and others. In this study, an artificial neural network (ANN) model is proposed to estimate the permeability coefficient with various permeability test sets. The permeability coefficient was modeled as a function of six variables including the natural water content, specific gravity, and grain sizes. 379 in-situ permeability tests performed at 21 construction sites in Korea were used for the training and testing of the ANN model. It was found that the permeability coefficient could be reasonably estimated using developed neural network model.
- 29 June 2011
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 29 (4) , 267-278
Development of Neural Network Model to Estimate the Permeability Coefficient of Soils
The permeability coefficient is a one of the important soil parameters that is essential to geotechnical designs. As the determination of the permeability coefficient from field tests is relatively time-consuming, empirical formulas based on soil parameters can be useful. Over the decades, a number of empirical formulas have been proposed to relate the compressibility to other soil parameters, such as the natural water content, grain size, specific gravity, and others. In this study, an artificial neural network (ANN) model is proposed to estimate the permeability coefficient with various permeability test sets. The permeability coefficient was modeled as a function of six variables including the natural water content, specific gravity, and grain sizes. 379 in-situ permeability tests performed at 21 construction sites in Korea were used for the training and testing of the ANN model. It was found that the permeability coefficient could be reasonably estimated using developed neural network model.
- 19 November 2010
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 28 (4) , 324-344
Neural Network Model for Predicting the Resistance of Driven Piles
Although numerous investigations have been performed over the years to predict the behavior and resistance of piles, the mechanisms are not yet entirely understood. Predicting pile resistance is a difficult task because there are a large number of parameters affecting the capacity that have complex relationships with each other. It is extremely difficult to develop appropriate relationships between various essential parameters, including the soil condition, pile type, driving condition, time effect, and others. This paper describes the application of an artificial neural network (ANN) to predict the resistance of driven piles in dynamic load tests. The training and testing of the ANN were based on 165 data points for driven piles at various construction sites in Korea. Predictions on the tip, shaft, and total pile resistance were made for piles with available corresponding measurements of such values. The effect of the essential parameters on the pile resistance values was investigated through parametric analysis using ANN modeling. The results of this study indicate that the ANN model serves as a reliable and simple predictive tool to appropriately consider various essential parameters for predicting the resistance of driven piles.
- 19 November 2010
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 28 (4) , 324-344
Neural Network Model for Predicting the Resistance of Driven Piles
Although numerous investigations have been performed over the years to predict the behavior and resistance of piles, the mechanisms are not yet entirely understood. Predicting pile resistance is a difficult task because there are a large number of parameters affecting the capacity that have complex relationships with each other. It is extremely difficult to develop appropriate relationships between various essential parameters, including the soil condition, pile type, driving condition, time effect, and others. This paper describes the application of an artificial neural network (ANN) to predict the resistance of driven piles in dynamic load tests. The training and testing of the ANN were based on 165 data points for driven piles at various construction sites in Korea. Predictions on the tip, shaft, and total pile resistance were made for piles with available corresponding measurements of such values. The effect of the essential parameters on the pile resistance values was investigated through parametric analysis using ANN modeling. The results of this study indicate that the ANN model serves as a reliable and simple predictive tool to appropriately consider various essential parameters for predicting the resistance of driven piles.
- 19 November 2010
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 28 (4) , 363-374
Evaluation of Bearing Capacity for Multi-Layered Clay Deposits with Geosynthetic Reinforcement using Discrete Element Method
A stability analysis of reinforced foundation soil is presented in this paper. A method based on the discrete element method (DEM) is suggested for calculating the bearing capacity on strip footings over multilayer soils reinforced with a horizontal layer of geosynthetics. The proposed method can estimate the ultimate bearing capacity and the distribution of tensile force developed in the geosynthetics of the footing system by Winkler springs to account for the compatibility between soil blocks and tensile elements to consider the tensile behavior between soil and geosynthetics. For footings on various multilayer soils with or without reinforcement of geosynthetics, the results of the method were compared to the field test results as well as to those obtained by various methods proposed by other researchers.
- 19 November 2010
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 28 (4) , 363-374
Evaluation of Bearing Capacity for Multi-Layered Clay Deposits with Geosynthetic Reinforcement using Discrete Element Method
A stability analysis of reinforced foundation soil is presented in this paper. A method based on the discrete element method (DEM) is suggested for calculating the bearing capacity on strip footings over multilayer soils reinforced with a horizontal layer of geosynthetics. The proposed method can estimate the ultimate bearing capacity and the distribution of tensile force developed in the geosynthetics of the footing system by Winkler springs to account for the compatibility between soil blocks and tensile elements to consider the tensile behavior between soil and geosynthetics. For footings on various multilayer soils with or without reinforcement of geosynthetics, the results of the method were compared to the field test results as well as to those obtained by various methods proposed by other researchers.
- 22 February 2010
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 28 (1) , 37-48
Neural Network Formula for Local Scour at Piers Using Field Data
It is known that the scour at bridge piers is among the leading causes of bridge failure. However, the mechanism of flow around a pier structure is so complicated that it is difficult to establish a general empirical model to provide accurate estimation for scour. Each of the proposed empirical formulas yields good results for a particular data set, but cannot accurately or reliably predict scour from various data sets. In this study, an alternative approach, an artificial neural network (ANN) model, is proposed to estimate the local scour depth with numerous field data bases. The local scour depth was modeled as a function of six non-dimensional variables: V 2/gb, y/b, b/D 50, l/b, pier skew angle, and pier shape. Four hundred and ten field data points were used for the training and testing of the ANN model. The predicted results showed that the neural network could provide better performance than the empirical equations.
- 22 February 2010
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 28 (1) , 37-48
Neural Network Formula for Local Scour at Piers Using Field Data
It is known that the scour at bridge piers is among the leading causes of bridge failure. However, the mechanism of flow around a pier structure is so complicated that it is difficult to establish a general empirical model to provide accurate estimation for scour. Each of the proposed empirical formulas yields good results for a particular data set, but cannot accurately or reliably predict scour from various data sets. In this study, an alternative approach, an artificial neural network (ANN) model, is proposed to estimate the local scour depth with numerous field data bases. The local scour depth was modeled as a function of six non-dimensional variables: V 2/gb, y/b, b/D 50, l/b, pier skew angle, and pier shape. Four hundred and ten field data points were used for the training and testing of the ANN model. The predicted results showed that the neural network could provide better performance than the empirical equations.
- 1 March 2007
- Published by Taylor & Francis in Journal of the Air & Waste Management Association
- Vol. 57 (2) , 243-251
Analysis of Long-Term Settlement of Municipal Solid Waste Landfills as Determined by Various Settlement Estimation Methods
In this study, several existing municipal solid waste (MSW) settlement estimation methods are reviewed and applied to analyze the settlement data of nine MSW land-fills. Because a biodegradation-related settlement contributes differently to a long-term total settlement depending on the age of landfills, the actual MSW landfill sites are classified into three groups to specifically address the validity of each method in its prediction of a long-term settlement for each age category. Results demonstrate that there are considerable decreases in predicted settlement potentials as fill age increases. Comparisons indicate that the individual estimation methods display a considerable variation in predicting settlements in the fresh MSW landfills. On the other hand, for the old refuse landfills, all of the estimation methods, except the extended soil model, predict low settlement potentials.
- 1 March 2007
- Published by Taylor & Francis in Journal of the Air & Waste Management Association
- Vol. 57 (2) , 243-251
Analysis of Long-Term Settlement of Municipal Solid Waste Landfills as Determined by Various Settlement Estimation Methods
In this study, several existing municipal solid waste (MSW) settlement estimation methods are reviewed and applied to analyze the settlement data of nine MSW land-fills. Because a biodegradation-related settlement contributes differently to a long-term total settlement depending on the age of landfills, the actual MSW landfill sites are classified into three groups to specifically address the validity of each method in its prediction of a long-term settlement for each age category. Results demonstrate that there are considerable decreases in predicted settlement potentials as fill age increases. Comparisons indicate that the individual estimation methods display a considerable variation in predicting settlements in the fresh MSW landfills. On the other hand, for the old refuse landfills, all of the estimation methods, except the extended soil model, predict low settlement potentials.
- 1 January 2007
- Published by American Society of Civil Engineers (ASCE) in Journal of Environmental Engineering
- Vol. 133 (1) , 64-72
Parameter Evaluation and Performance Comparison of MSW Settlement Prediction Models in Various Landfill Types
Estimation of settlement for municipal solid waste (MSW) landfills is critical to the successful site operation and maintenance as well as to the future development of the sites. In this paper, the six existing settlement prediction models are analyzed according to the three landfill types. 15 MSW landfill sites are classified into three categories, Types I, II, and III depending on their settlement activity levels and fill age. Measured settlement data of each landfill site are plotted as a strain curve on a logarithmic time scale, and the slope of the curve is used to determine a settlement activity level. First, the parameters of each prediction model are evaluated to determine their typical values for each type of the landfills. The results will serve as a basis for engineers to determine if their calculated model parameters are within the typical ranges. Second, each model’s performance of predicting settlement for the landfill sites is analyzed against the measured settlement data to compare the mod...
- 1 January 2007
- Published by American Society of Civil Engineers (ASCE) in Journal of Environmental Engineering
- Vol. 133 (1) , 64-72
Parameter Evaluation and Performance Comparison of MSW Settlement Prediction Models in Various Landfill Types
Estimation of settlement for municipal solid waste (MSW) landfills is critical to the successful site operation and maintenance as well as to the future development of the sites. In this paper, the six existing settlement prediction models are analyzed according to the three landfill types. 15 MSW landfill sites are classified into three categories, Types I, II, and III depending on their settlement activity levels and fill age. Measured settlement data of each landfill site are plotted as a strain curve on a logarithmic time scale, and the slope of the curve is used to determine a settlement activity level. First, the parameters of each prediction model are evaluated to determine their typical values for each type of the landfills. The results will serve as a basis for engineers to determine if their calculated model parameters are within the typical ranges. Second, each model’s performance of predicting settlement for the landfill sites is analyzed against the measured settlement data to compare the mod...
- 21 February 2006
- Published by American Society of Civil Engineers (ASCE)
- p. 1-6
Consolidation Characteristics of SCP-Reinforced Composite Ground
Sand compaction pile (SCP) method is composed of compacted sand pile inserted into the soft clay deposit by displacement method. SCP-reinforced ground is composite soil which consists of the SCP and the surrounding soft soil. While a surcharge load is applied on composite ground, time-dependent behavior occurs in the soft soil due to consolidation according to radial flow toward SCP and the corresponding stress transfer also takes place between the SCP and the soft soil. This paper presents the numerical results of cylindrical composite ground to investigate consolidation characteristics and the stress transfer mechanism of composite ground reinforced by SCP under quaywall. The results show that the consolidation of soft clay gives a significant effect on the stress transfer mechanism and stress concentration ratio of composite ground.
- 21 February 2006
- Published by American Society of Civil Engineers (ASCE)
- p. 1-6
Consolidation Characteristics of SCP-Reinforced Composite Ground
Sand compaction pile (SCP) method is composed of compacted sand pile inserted into the soft clay deposit by displacement method. SCP-reinforced ground is composite soil which consists of the SCP and the surrounding soft soil. While a surcharge load is applied on composite ground, time-dependent behavior occurs in the soft soil due to consolidation according to radial flow toward SCP and the corresponding stress transfer also takes place between the SCP and the soft soil. This paper presents the numerical results of cylindrical composite ground to investigate consolidation characteristics and the stress transfer mechanism of composite ground reinforced by SCP under quaywall. The results show that the consolidation of soft clay gives a significant effect on the stress transfer mechanism and stress concentration ratio of composite ground.
- 1 March 2005
- Published by Taylor & Francis in Journal of the Air & Waste Management Association
- Vol. 55 (3) , 283-290
Compressibility of Municipal Solid Waste Codisposed with Fly Ash
If a municipal solid waste (MSW) landfill is used as the foundation for a construction site, the change in the loading conditions may cause considerable compression of the landfill. Therefore, reinforcement to compensate for the loose compression nature of a MSW landfill is a very important design factor for geotechnical engineers when considering the end-use of the landfill. In this study, we discuss a possible technique for stabilizing MSW landfills through the codisposal of municipal solid waste and fly ash. To estimate the stabilization based on the compression characteristics of the codisposed landfill, we performed tests using a large compression set and experimental cells. According to the test results, if the proportion of fly ash is increased, initial and long-term compression could be reduced.
- 1 March 2005
- Published by Taylor & Francis in Journal of the Air & Waste Management Association
- Vol. 55 (3) , 283-290
Compressibility of Municipal Solid Waste Codisposed with Fly Ash
If a municipal solid waste (MSW) landfill is used as the foundation for a construction site, the change in the loading conditions may cause considerable compression of the landfill. Therefore, reinforcement to compensate for the loose compression nature of a MSW landfill is a very important design factor for geotechnical engineers when considering the end-use of the landfill. In this study, we discuss a possible technique for stabilizing MSW landfills through the codisposal of municipal solid waste and fly ash. To estimate the stabilization based on the compression characteristics of the codisposed landfill, we performed tests using a large compression set and experimental cells. According to the test results, if the proportion of fly ash is increased, initial and long-term compression could be reduced.