Alena Vagaská
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alena Vagaská has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Jan Valíček
Department of Electrical Engineering, Automation and Informatics, Faculty of Engineering, Slovak University of Agriculture in Nitra, Tr. A. Hlinku 2, 949 76 Nitra, Slovakia
3 shared publications - Jan Řehoř
University of West Bohemia
3 shared publications - Jaroslava Fulemová
Regional Technology Institute, Faculty of Mechanical Engineering, University of West Bohemia, Univerzitni 8, 306 14 Pilsen, Czech Republic
3 shared publications - Marta Harničárová
Department of Mechanical Engineering, Faculty of Technology, Institute of Technology and Business in České Budějovice, Okružní 10, 370 01 České Budějovice, Czech Republic
3 shared publications - Miroslav Gombár
Department of Machining Technology, Faculty of Mechanical Engineering, University of West Bohemia in Pilsen, 30100 Pilsen, Czech Republic
3 shared publications - Milena Kušnerová
Department of Mechanical Engineering, Faculty of Technology, Institute of Technology and Business in České Budějovice, 370 01 České Budějovice, Czech Republic
2 shared publications
Latest Publications
- 23 May 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (1-2) , 889-901
Investigation of machining of Stellite 6 alloy deposited on steel substrate
- 23 May 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (1-2) , 889-901
Investigation of machining of Stellite 6 alloy deposited on steel substrate
- Open Access
- 6 April 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (7) , 2524
Prediction of Cutting Parameters of HVOF-Sprayed Stellite 6
In this research, the authors set out to propose a new method of predicting and adjusting the main cutting parameters of chip machining, namely spraying on the substrate. In the experiments, a total of 28 turning cuts on a Stellite 6 coating layer were realized. The base materials of the Stellite 6 layers were EN S235JRG1 and carbide WC-Co. This work aimed to find out and optimize the influence of different combinations of cutting parameters. Due to the coating solution, the work is focused on the evaluation of the roughness Ra (μm) of the turned substrate, the grain size Dgr (μm) of the spraying, the normal stress σrz (MPa), the residual stress σrez (MPa), the specific cutting force Fc (N), the quality of adhesion to the substrate Adhmp (MPa) and other parameters. For the sake of a comprehensive solution to the problem, several new predictive equations and subsequent suggestions for solutions have been derived from this research topic based on the newly obtained experimental results. The proposed models and procedures make it possible to get new results and insights into coating technologies.
- 6 April 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (7) , 2524
Open AccessPrediction of Cutting Parameters of HVOF-Sprayed Stellite 6
In this research, the authors set out to propose a new method of predicting and adjusting the main cutting parameters of chip machining, namely spraying on the substrate. In the experiments, a total of 28 turning cuts on a Stellite 6 coating layer were realized. The base materials of the Stellite 6 layers were EN S235JRG1 and carbide WC-Co. This work aimed to find out and optimize the influence of different combinations of cutting parameters. Due to the coating solution, the work is focused on the evaluation of the roughness Ra (μm) of the turned substrate, the grain size Dgr (μm) of the spraying, the normal stress σrz (MPa), the residual stress σrez (MPa), the specific cutting force Fc (N), the quality of adhesion to the substrate Adhmp (MPa) and other parameters. For the sake of a comprehensive solution to the problem, several new predictive equations and subsequent suggestions for solutions have been derived from this research topic based on the newly obtained experimental results. The proposed models and procedures make it possible to get new results and insights into coating technologies.
- Open Access
Investigation of Surface Roughness and Predictive Modelling of Machining Stellite 6
The aim of the paper was to examine the influence of cutting conditions on the roughness of surfaces machined by longitudinal turning, namely of surfaces coated with Stellite 6 prepared by high-velocity oxygen fuel (HVOF) technology and applied onto a standard structural steel substrate. From the results of measurements of the cutting parameters, a prediction model of the roughness parameters was created using mathematical and statistical methods. Based on a more detailed analysis and data comparison, a new method for prediction of parameters of longitudinal turning technology was obtained. The main aim of the paper was to identify the mutual discrete relationships between the substrate roughness and the machining parameters. These were the feed rate vc (m·min−1), in the case of turning and milling, and the feed rate f (mm·rev−1) and the depth of cut ap (mm). The paper compared and verified two approaches of this method, namely the mathematical statistical approach, the analytical approach and measured dates. From the evaluated and interpreted results, new equations were formulated, enabling prediction of the material parameters of the workpiece, the technological parameters and the parameters of surface quality.
Open AccessInvestigation of Surface Roughness and Predictive Modelling of Machining Stellite 6
The aim of the paper was to examine the influence of cutting conditions on the roughness of surfaces machined by longitudinal turning, namely of surfaces coated with Stellite 6 prepared by high-velocity oxygen fuel (HVOF) technology and applied onto a standard structural steel substrate. From the results of measurements of the cutting parameters, a prediction model of the roughness parameters was created using mathematical and statistical methods. Based on a more detailed analysis and data comparison, a new method for prediction of parameters of longitudinal turning technology was obtained. The main aim of the paper was to identify the mutual discrete relationships between the substrate roughness and the machining parameters. These were the feed rate vc (m·min−1), in the case of turning and milling, and the feed rate f (mm·rev−1) and the depth of cut ap (mm). The paper compared and verified two approaches of this method, namely the mathematical statistical approach, the analytical approach and measured dates. From the evaluated and interpreted results, new equations were formulated, enabling prediction of the material parameters of the workpiece, the technological parameters and the parameters of surface quality.