Shirley Shen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Shirley Shen has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Yue Huang
Faculties of Engineering and Physical Sciences and Environment, University of Leeds, Leeds LS2 9JT, UK
2 shared publications - Adrian Trinchi
CSIRO Manufacturing, Stewart Bastow Building, Clayton, Victoria, 3169, Australia
1 shared publication - Antonella Sola
Department of Sciences and Methods for Engineering, University of Modena and Reggio Emilia, Via Amendola 2, 42122 Reggio Emilia, Italy
1 shared publication Clement Chu
CSIRO Manufacturing,Clayton,VIC,Australia,3169
1 shared publication- Hao-Yang Liu
State Key Laboratory of Medicinal Chemical Biology, Frontiers Science Center for New Organic Matter, Tianjin Key Laboratory of Biosensing and Molecular Recognition, Research Center for Analytical Sciences, College of Chemistry, School of Medicine and Frontiers Science Center for Cell Responses, Nankai University, Tianjin, P. R. China
1 shared publication Huan Yang
Xiamen University
1 shared publication
Latest Publications
- 2 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
UIT - A Universal Identifier of Things to Bridge Cyber and Physical Worlds
Ensuring the integrity of product manufacture information and securely verifying the authenticity of a component is critical for both manufacturers and customers. However, traditional product identifying solutions offer little protection over counterfeit and cyber-attack. We propose a Blockchain-based product identification and certification system called Universal Identifier of Things (UIT) that enables fast product authenticity verification using low-cost devices. We leverage additive manufacturing technologies to embed a unique identifier into a product. The identifier is then digitalized by generating a digital certificate which is stored on Blockchain during the whole product life cycle for various applications/services (provenance, traceability, product warranty and call-back, etc.). We prove this concept by integrating 3D printing and Hyperledger Blockchain technologies to demonstrate that we can ensure the integrity of products with UIT by bridging the cyber and physical worlds.
- 2 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
UIT - A Universal Identifier of Things to Bridge Cyber and Physical Worlds
Ensuring the integrity of product manufacture information and securely verifying the authenticity of a component is critical for both manufacturers and customers. However, traditional product identifying solutions offer little protection over counterfeit and cyber-attack. We propose a Blockchain-based product identification and certification system called Universal Identifier of Things (UIT) that enables fast product authenticity verification using low-cost devices. We leverage additive manufacturing technologies to embed a unique identifier into a product. The identifier is then digitalized by generating a digital certificate which is stored on Blockchain during the whole product life cycle for various applications/services (provenance, traceability, product warranty and call-back, etc.). We prove this concept by integrating 3D printing and Hyperledger Blockchain technologies to demonstrate that we can ensure the integrity of products with UIT by bridging the cyber and physical worlds.
- 13 December 2019
- Published by Wiley in International Journal of Applied Glass Science
- Vol. 11 (2) , 329-339
Strengthening mechanism of cover glass by Sol‐Gel SiO 2 coating
Strengthening is a huge challenge of ultrathin cover glass in mobile electronic devices. In this paper, a transparent sol‐gel silica coating has been sprayed on the surface of chemically strengthened cover glass, and three different coatings (identified as thickness/curing temperature: 3 μm/80°C, 5 μm/80°C, and 3 μm/180°C) have been prepared. Characterized by four‐point bending experiment, the strengthening effects of three coatings, representing by the increases of strength of the coated glass, are 47 MPa, 98 MPa, and 58 MPa for 3 μm/80°C, 5 μm/80°C, and 3 μm/180°C, respectively. Based on finite element simulation and experimental data of four‐point bending, the influence of four parameters of surface coating (elastic modulus, residual stress, filling ratio, and thickness) on glass strengthening has been investigated. Simulation analysis shows that the increase of elastic modulus, residual stress, and filling ratio of the SiO 2 coating facilitates the increase of bending strength of cover glass, and the coating thickness has less influence on the glass strength. However, the experimental results demonstrate that the coating thickness has a significant impact on the strength of glass: when the layer thickness of sample cured at 80°C increases from 3μm to 5μm, the bending strength of glass can improve by 51MPa. Since greater coating thickness induces greater filling ratio, which is the main contributor to the strengthening effect of increased coating thickness, so, elastic modulus, residual stress, and filling ratio of the coating are the three key factors of the cover glass strengthening.
- 13 December 2019
- Published by Wiley in International Journal of Applied Glass Science
- Vol. 11 (2) , 329-339
Strengthening mechanism of cover glass by Sol‐Gel SiO 2 coating
Strengthening is a huge challenge of ultrathin cover glass in mobile electronic devices. In this paper, a transparent sol‐gel silica coating has been sprayed on the surface of chemically strengthened cover glass, and three different coatings (identified as thickness/curing temperature: 3 μm/80°C, 5 μm/80°C, and 3 μm/180°C) have been prepared. Characterized by four‐point bending experiment, the strengthening effects of three coatings, representing by the increases of strength of the coated glass, are 47 MPa, 98 MPa, and 58 MPa for 3 μm/80°C, 5 μm/80°C, and 3 μm/180°C, respectively. Based on finite element simulation and experimental data of four‐point bending, the influence of four parameters of surface coating (elastic modulus, residual stress, filling ratio, and thickness) on glass strengthening has been investigated. Simulation analysis shows that the increase of elastic modulus, residual stress, and filling ratio of the SiO 2 coating facilitates the increase of bending strength of cover glass, and the coating thickness has less influence on the glass strength. However, the experimental results demonstrate that the coating thickness has a significant impact on the strength of glass: when the layer thickness of sample cured at 80°C increases from 3μm to 5μm, the bending strength of glass can improve by 51MPa. Since greater coating thickness induces greater filling ratio, which is the main contributor to the strengthening effect of increased coating thickness, so, elastic modulus, residual stress, and filling ratio of the coating are the three key factors of the cover glass strengthening.
- 10 August 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 54 (1) , 693-704
Intracellular pathway of halloysite nanotubes: potential application for antitumor drug delivery
- 10 August 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 54 (1) , 693-704
Intracellular pathway of halloysite nanotubes: potential application for antitumor drug delivery
- 25 January 2013
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 743-744, 377-381
Fabrication and Characterization for Innate Super-Hydrophilic SiO2 Thin Films
Distinguished with photoinduced super-hydrophilic inorganic thin films, non-photoinduced innate super-hydrophilic SiO2 thin films were successfully fabricated in this work. The SiO2 sol was prepared by acid-base two-step sol-gel method. The mix solution containing SiO2 sol and polyethylene glycol (PEG) was coated on glass substrate and then went through thermal treatment to obtain innate super-hydrophilic SiO2 thin films. The films were characterized by atomic force microscopy (AFM), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR) and contact angle meter. The results show that the surface concave-convex microstructure and the hydroxyl content are the factors that endow the SiO2 coating films with innate super-hydrophilic property.
- 25 January 2013
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 743-744, 377-381
Fabrication and Characterization for Innate Super-Hydrophilic SiO2 Thin Films
Distinguished with photoinduced super-hydrophilic inorganic thin films, non-photoinduced innate super-hydrophilic SiO2 thin films were successfully fabricated in this work. The SiO2 sol was prepared by acid-base two-step sol-gel method. The mix solution containing SiO2 sol and polyethylene glycol (PEG) was coated on glass substrate and then went through thermal treatment to obtain innate super-hydrophilic SiO2 thin films. The films were characterized by atomic force microscopy (AFM), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR) and contact angle meter. The results show that the surface concave-convex microstructure and the hydroxyl content are the factors that endow the SiO2 coating films with innate super-hydrophilic property.