Marko Tošić
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Marko Tošić has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Roland Larsson
Division of Machine Elements, Luleå University of Technology, 97187 Luleå, Sweden
3 shared publications - Thomas Lohner
Gear Research Center (FZG), Department of Mechanical Engineering, School of Engineering and Design, Technical University of Munich, Garching near Munich, Germany
3 shared publications - Karsten Stahl
Technical University of Munich
2 shared publications - Janko Jovanovic
Univ Montenegro, Fac Mech Engn, Podgorica, Montenegro
1 shared publication - Marcus Björling
Luleå University of Technology Division of Machine Elements
1 shared publication
Latest Publications
- Open Access
Thermal Elastohydrodynamic Analysis of a Worm Gear
This study explores the elastohydrodynamic lubrication (EHL) between the contacting tooth flanks of a worm gear with nonconjugate meshing action. The contact is characterized by a slender-like elliptical shape and high sliding. The geometry and contact conditions for the considered worm gear were obtained using tooth contact analysis. Based on that, the complete area of the worm gear contact was analyzed using a validated numerical EHL model considering non-Newtonian, thermal, and transient effects. The geometrical and kinematic design factors that influence EHL film formation in worm gears were identified and discussed. The results show the specific characteristics of worm gear EHL contacts, such as the very slender contact in the tooth root flank area, which diminishes the effect of the entrainment speed on film thickness. EHL film formation could be supported by increasing conformity between the flanks to make the contact less slender. By comparing the film thickness results against analytically obtained ones, relatively large differences were observed except for one formula for minimum film thickness.
Open AccessThermal Elastohydrodynamic Analysis of a Worm Gear
This study explores the elastohydrodynamic lubrication (EHL) between the contacting tooth flanks of a worm gear with nonconjugate meshing action. The contact is characterized by a slender-like elliptical shape and high sliding. The geometry and contact conditions for the considered worm gear were obtained using tooth contact analysis. Based on that, the complete area of the worm gear contact was analyzed using a validated numerical EHL model considering non-Newtonian, thermal, and transient effects. The geometrical and kinematic design factors that influence EHL film formation in worm gears were identified and discussed. The results show the specific characteristics of worm gear EHL contacts, such as the very slender contact in the tooth root flank area, which diminishes the effect of the entrainment speed on film thickness. EHL film formation could be supported by increasing conformity between the flanks to make the contact less slender. By comparing the film thickness results against analytically obtained ones, relatively large differences were observed except for one formula for minimum film thickness.
- Open Access
- 6 May 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (5) , 89
Thermal Effects in Slender EHL Contacts
This study deals with experimental and numerical analysis of the thermal effects of slender elastohydrodynamically lubricated (EHL) contacts under high sliding. Thereby, the entrainment direction is along the major axis of the contact ellipse. Film thickness measurements were carried out on an optical EHL tribometer with a glass disk and steel roller. Numerical EHL solutions were obtained with consideration for non-Newtonian rheology and thermal effects. The results show that thermal effects can result in a strong viscosity wedge diverting oil flow to the contact sides. For high positive sliding, in which the glass disk moves faster, the influence of entrainment speed on minimum film thickness is almost negligible, while the film thickness shows a continuous decrease in gap length direction.
- 6 May 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (5) , 89
Open AccessThermal Effects in Slender EHL Contacts
This study deals with experimental and numerical analysis of the thermal effects of slender elastohydrodynamically lubricated (EHL) contacts under high sliding. Thereby, the entrainment direction is along the major axis of the contact ellipse. Film thickness measurements were carried out on an optical EHL tribometer with a glass disk and steel roller. Numerical EHL solutions were obtained with consideration for non-Newtonian rheology and thermal effects. The results show that thermal effects can result in a strong viscosity wedge diverting oil flow to the contact sides. For high positive sliding, in which the glass disk moves faster, the influence of entrainment speed on minimum film thickness is almost negligible, while the film thickness shows a continuous decrease in gap length direction.
- Open Access
- 12 August 2019
- Published by MDPI AG in Lubricants
- Vol. 7 (8) , 69
A Computational Fluid Dynamics Study on Shearing Mechanisms in Thermal Elastohydrodynamic Line Contacts
A computational fluid dynamics (CFD) model of the thermal elastohydrodynamically lubricated (EHL) line contact problem has been developed for the purpose of exploring the physical processes that occur inside a thin EHL film subjected to shearing motion. The Navier–Stokes equations are solved by using the finite volume method (FVM) in a commercial CFD software, ANSYS Fluent. A set of user-defined functions (UDF) are used for computing viscosity, density, heat source, temperature of moving surfaces and elastic deformation of the top roller according to well-established equations commonly used in the EHL theory. The cavitation problem is solved by taking into account multiphase mixture flow. The model combinations of Houpert and Ree–Eyring and of Tait and Carreau were used for modeling the non-Newtonian behavior of Squalane and the results were compared. Both rheological models suggest the existence of shear-band and plug-flow at high fluid pressure. Due to the differences in viscosity at GPa-level pressure, the chosen model has substantial influence on the computed shear stress and temperature distributions in the high-pressure region. This shows the importance of using correct rheology information in the whole range of pressure, temperature, and shear strain rate.
- 12 August 2019
- Published by MDPI AG in Lubricants
- Vol. 7 (8) , 69
Open AccessA Computational Fluid Dynamics Study on Shearing Mechanisms in Thermal Elastohydrodynamic Line Contacts
A computational fluid dynamics (CFD) model of the thermal elastohydrodynamically lubricated (EHL) line contact problem has been developed for the purpose of exploring the physical processes that occur inside a thin EHL film subjected to shearing motion. The Navier–Stokes equations are solved by using the finite volume method (FVM) in a commercial CFD software, ANSYS Fluent. A set of user-defined functions (UDF) are used for computing viscosity, density, heat source, temperature of moving surfaces and elastic deformation of the top roller according to well-established equations commonly used in the EHL theory. The cavitation problem is solved by taking into account multiphase mixture flow. The model combinations of Houpert and Ree–Eyring and of Tait and Carreau were used for modeling the non-Newtonian behavior of Squalane and the results were compared. Both rheological models suggest the existence of shear-band and plug-flow at high fluid pressure. Due to the differences in viscosity at GPa-level pressure, the chosen model has substantial influence on the computed shear stress and temperature distributions in the high-pressure region. This shows the importance of using correct rheology information in the whole range of pressure, temperature, and shear strain rate.