Jing Lin Tong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jing Lin Tong has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Bo Zhao
University of Electronic Science and Technology of China
2 shared publications - Feng Jiao
School of Mechanical and Power Engineering, Henan Polytechnic University, Jiaozuo, China
1 shared publication - Gaoming Huang
College of Electronic Engineering Naval University of Engineering Wuhan People's Republic of China
1 shared publication Guo Fu Gao
Henan Polytechnic University
1 shared publication- Peng Huafu
College of Electronic Engineering, Naval University of Engineering, Wuhan, 430033 China
1 shared publication Tian Wei
College of Electronic Engineering, Naval University of Engineering, Wuhan, 430033 China
1 shared publication
Latest Publications
- Open Access
- 2 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 106761-106772
Cramér–Rao Lower Bound Analysis for Stochastic Model Based Target Parameter Estimation in Multistatic Passive Radar With Direct-Path Interference
This paper addresses the problem of Cramér–Rao lower bound (CRLB) analysis for joint target location and velocity estimation in a multistatic passive radar system comprised of multiple noncooperative illuminators of opportunity (IOs) and multiple geographically separated receivers. Unlike other existing studies, special attention in this work is paid to a more ubiquitous scenario, in which no reference channel exists in receiver networks. Besides, the situation where the measurements collected at the receivers are contaminated by the interference directly illuminated from IOs is taken into account. Namely, each receive station simultaneously obtains direct-path interference (DPI) from all IOs and echo signals reflected by the target. Further, the IO waveform is modeled as a stochastic process in which samples of the unknown IO waveform are treated as a complex Gaussian sequence. Finally, the effects of multipath clutter on the signal model and CRLB are well analyzed. Numerical results are provided to prove that the joint CRLB is not only a function of signal-to-noise ratio (SNR), DPI-to-noise ratio (DNR), and clutter-to-noise ratio (CNR), but also associated with both IO waveform parameters and relative geographical distribution of the system.
- 2 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 106761-106772
Open AccessCramér–Rao Lower Bound Analysis for Stochastic Model Based Target Parameter Estimation in Multistatic Passive Radar With Direct-Path Interference
This paper addresses the problem of Cramér–Rao lower bound (CRLB) analysis for joint target location and velocity estimation in a multistatic passive radar system comprised of multiple noncooperative illuminators of opportunity (IOs) and multiple geographically separated receivers. Unlike other existing studies, special attention in this work is paid to a more ubiquitous scenario, in which no reference channel exists in receiver networks. Besides, the situation where the measurements collected at the receivers are contaminated by the interference directly illuminated from IOs is taken into account. Namely, each receive station simultaneously obtains direct-path interference (DPI) from all IOs and echo signals reflected by the target. Further, the IO waveform is modeled as a stochastic process in which samples of the unknown IO waveform are treated as a complex Gaussian sequence. Finally, the effects of multipath clutter on the signal model and CRLB are well analyzed. Numerical results are provided to prove that the joint CRLB is not only a function of signal-to-noise ratio (SNR), DPI-to-noise ratio (DNR), and clutter-to-noise ratio (CNR), but also associated with both IO waveform parameters and relative geographical distribution of the system.
- 1 August 2012
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 522, 173-177
Study on Residual Stress of GCr15 Bearing Steel under Ultrasonic Vibration Turning
The effects of the cutting parameters on residual stresss were investigated in common and ultrasonic vibration hard turning bearing steel GCr15 with PCBN. The residual stresses under the machined surface were measured by X-ray diffraction technique. The results obtained in this study show that residual compressive stress is produced both in common and ultrasonic turning of GCr15 bearing steel. Under the same turning condition the residual compressive produced by the ultrasonic turning is smaller than that by the common turning. Residual compressive stress can improve the fatigue performance and life of workpiece, so the cutting parameters should be optimized to get the best residual compressive stress in ultrasonic turning.
- 1 August 2012
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 522, 173-177
Study on Residual Stress of GCr15 Bearing Steel under Ultrasonic Vibration Turning
The effects of the cutting parameters on residual stresss were investigated in common and ultrasonic vibration hard turning bearing steel GCr15 with PCBN. The residual stresses under the machined surface were measured by X-ray diffraction technique. The results obtained in this study show that residual compressive stress is produced both in common and ultrasonic turning of GCr15 bearing steel. Under the same turning condition the residual compressive produced by the ultrasonic turning is smaller than that by the common turning. Residual compressive stress can improve the fatigue performance and life of workpiece, so the cutting parameters should be optimized to get the best residual compressive stress in ultrasonic turning.
- 1 June 2011
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 175, 126-130
Research on CBN Grinding Wheel Dressing with Ultrasonic Vibration Assistance and its Grinding Performance
The experiment of resin-bonded CBN wheel dressing using a diamond dresser assisted with longitudinal ultrasonic vibration along the direction of depth of cut was carried out and the dressing characteristics and grinding performance were discussed in the present paper. The influence of acoustic parameters on the topography of CBN wheel was studied to check the effectiveness of dressing for this method. The experimental results showed that the higher the ultrasonic frequency is, the better the wheel topography. The grinding on K9 optical glass and high speed steel has achieved higher G-ratio than that of traditionally mechanical dressed CBN grinding wheel. The ground surface of high speed steel is better than that of K9 optical glass. According to the interferometer images, it was concluded that the grinding of high speed steel was in ductile cutting regime, while removal of K9 optical glass was in brittle fracture regime.
- 1 June 2011
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 175, 126-130
Research on CBN Grinding Wheel Dressing with Ultrasonic Vibration Assistance and its Grinding Performance
The experiment of resin-bonded CBN wheel dressing using a diamond dresser assisted with longitudinal ultrasonic vibration along the direction of depth of cut was carried out and the dressing characteristics and grinding performance were discussed in the present paper. The influence of acoustic parameters on the topography of CBN wheel was studied to check the effectiveness of dressing for this method. The experimental results showed that the higher the ultrasonic frequency is, the better the wheel topography. The grinding on K9 optical glass and high speed steel has achieved higher G-ratio than that of traditionally mechanical dressed CBN grinding wheel. The ground surface of high speed steel is better than that of K9 optical glass. According to the interferometer images, it was concluded that the grinding of high speed steel was in ductile cutting regime, while removal of K9 optical glass was in brittle fracture regime.