Pankaj Sarkar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Pankaj Sarkar has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Rowdra Ghatak
Department of Electronics and Communication Engineering, National Institute of Technology Durgapur, Durgapur, India
8 shared publications Rowdra Ghatak
Microwave and Antenna Research Laboratory, Electronics and Communication Engineering Department National Institute of Technology Durgapur Durgapur West Bengal India
7 shared publicationsManimala Pal
Department of ECE, Radio Engineering and Antenna Laboratory; NSHM Knowledge Campus; Durgapur West Bengal India
4 shared publications- Manimala Pal
Radio Engineering and Antenna Laboratory, Department Of Electronics and Communication Engineering; NFET; NSHM Knowledge Campus Durgapur Durgapur West Bengal 713212 India
4 shared publications Puja Kumari
Department of Electronics and Communication Engineering, National Institute of Technology Durgapur, Durgapur 713209, India
4 shared publicationsSangeeta Das
Electronics and Communication Engineering Department , School of Technology, North-Eastern Hill University , Shillong 793022 , Meghalaya , India
4 shared publications
Latest Publications
- 20 September 2024
- Published by Walter de Gruyter GmbH in Frequenz
- Vol. 79 (1-2) , 57-70
Design of a high selective triple band integrated reconfigurable filtering antenna for wideband and narrowband applications
The manuscript contributes a novel triple band integrated reconfigurable filtering antenna for wideband and narrowband applications. First, a compact dual band reconfigurable filter is conferred composed of two folded half-wavelength high impedance T-shaped resonators. The lower half of the feed lines comprises T-shaped resonator to obtain a passband from 2.8 to 3.5 GHz in order to cater WiMax band. The resonator at the upper half of the feed lines generates a passband from 5.15 to 5.75 GHz for WLAN operations. A transmission line is inserted underneath the feeding line to establish additional transmission zeroes. Two uniform impedance resonators (UIRs) are incorporated to the proposed dual band filter so that it can discard a band from 5.35 to 5.45 GHz by creating a notch at 5.4 GHz. Presence of notch band separates the WLAN band into two sub-bands. Thus, the proposed dual band filter can be easily reconfigured to a triple band bandpass filter. Later, a broadband antenna is implemented using a ground ring and an inverted L-shaped resonator which is radiating from 2.6 to 6 GHz. In the end, the filter is integrated with the antenna structure to develop the suggested triple-band reconfigurable filtering antenna. The developed filtering antenna is fabricated that perceives a fine agreement between the measured and the simulated response.
- 20 September 2024
- Published by Walter de Gruyter GmbH in Frequenz
- Vol. 79 (1-2) , 57-70
Design of a high selective triple band integrated reconfigurable filtering antenna for wideband and narrowband applications
The manuscript contributes a novel triple band integrated reconfigurable filtering antenna for wideband and narrowband applications. First, a compact dual band reconfigurable filter is conferred composed of two folded half-wavelength high impedance T-shaped resonators. The lower half of the feed lines comprises T-shaped resonator to obtain a passband from 2.8 to 3.5 GHz in order to cater WiMax band. The resonator at the upper half of the feed lines generates a passband from 5.15 to 5.75 GHz for WLAN operations. A transmission line is inserted underneath the feeding line to establish additional transmission zeroes. Two uniform impedance resonators (UIRs) are incorporated to the proposed dual band filter so that it can discard a band from 5.35 to 5.45 GHz by creating a notch at 5.4 GHz. Presence of notch band separates the WLAN band into two sub-bands. Thus, the proposed dual band filter can be easily reconfigured to a triple band bandpass filter. Later, a broadband antenna is implemented using a ground ring and an inverted L-shaped resonator which is radiating from 2.6 to 6 GHz. In the end, the filter is integrated with the antenna structure to develop the suggested triple-band reconfigurable filtering antenna. The developed filtering antenna is fabricated that perceives a fine agreement between the measured and the simulated response.
- 23 March 2024
- Published by Taylor & Francis in Journal of Electromagnetic Waves and Applications
- Vol. 38 (5) , 557-570
Design of a fractal triple-band reconfigurable filtering antenna for multiband applications
- 23 March 2024
- Published by Taylor & Francis in Journal of Electromagnetic Waves and Applications
- Vol. 38 (5) , 557-570
Design of a fractal triple-band reconfigurable filtering antenna for multiband applications
- 22 November 2023
- Published by Springer Nature
- p. 333-340
Compact Multi-Band Bandpass Filters Using Substrate Integrated Waveguide and Fractal Resonators
- 22 November 2023
- Published by Springer Nature
- p. 333-340
Compact Multi-Band Bandpass Filters Using Substrate Integrated Waveguide and Fractal Resonators
- 28 September 2022
- Published by Wiley in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 32 (12)
A dual‐band reconfigurable filtering antenna using PIN diodes for WiMAX and WLAN applications
- 28 September 2022
- Published by Wiley in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 32 (12)
A dual‐band reconfigurable filtering antenna using PIN diodes for WiMAX and WLAN applications
- 13 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 69 (6) , 2747-2751
A Bandwidth Reconfigurable Bandpass Filter for Ultrawideband and Wideband Applications
In this paper, a reconfigurable filter is proposed for simultaneous usage as ultra-wideband and wideband filters. The ultra-wideband (UWB) section is designed by constructing three parallelly connected quarter-wavelength transmission lines with two high impedance quarter-wavelength shorted stubs. The wideband (WB) section is implemented using an open stepped impedance stub-loaded resonator (OSSLR) and a shorted stepped impedance stub-loaded resonator (SSSLR). Nine pin diodes are embedded to switch the passband from UWB to WB and vice versa configuration. The filter in UWB mode produces a passband bandwidth (|S11| dB more than 10 dB) of 9.03 GHz from 2.15 GHz to 11.18 GHz, and the WB mode reports a passband bandwidth of 2.8 GHz, which ranges from 3.25 GHz to 6.05 GHz. Further, a lowpass filter is integrated with the design to obtain a wide upper stopband. The proposed prototype is fabricated and tested to validate the collaborative design concept. The overall circuit size of the prototype is 0.80λg × 0.42λg at 4.70 GHz.
- 13 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 69 (6) , 2747-2751
A Bandwidth Reconfigurable Bandpass Filter for Ultrawideband and Wideband Applications
In this paper, a reconfigurable filter is proposed for simultaneous usage as ultra-wideband and wideband filters. The ultra-wideband (UWB) section is designed by constructing three parallelly connected quarter-wavelength transmission lines with two high impedance quarter-wavelength shorted stubs. The wideband (WB) section is implemented using an open stepped impedance stub-loaded resonator (OSSLR) and a shorted stepped impedance stub-loaded resonator (SSSLR). Nine pin diodes are embedded to switch the passband from UWB to WB and vice versa configuration. The filter in UWB mode produces a passband bandwidth (|S11| dB more than 10 dB) of 9.03 GHz from 2.15 GHz to 11.18 GHz, and the WB mode reports a passband bandwidth of 2.8 GHz, which ranges from 3.25 GHz to 6.05 GHz. Further, a lowpass filter is integrated with the design to obtain a wide upper stopband. The proposed prototype is fabricated and tested to validate the collaborative design concept. The overall circuit size of the prototype is 0.80λg × 0.42λg at 4.70 GHz.
- 10 August 2021
- Published by Hindawi Limited in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 31 (11) , e22853
A quint mode fractal architecture based resonator and its efficacy in the design of multiband bandpass filters
This paper presents a new approach to design multiband bandpass filters (BPF) using multimode resonator topology inspired from Bamileke fractal architecture in the form of fractal shaped resonator. The proposed resonator architecture exhibits quint mode resonance behavior where resonance frequencies are determined using ABCD matrix. It offers flexibility in terms of choosing passband center frequencies precisely. Initially a second order dual band BPF is presented by suppressing higher order modes using asymmetric feed line. The same structure is used further to implement a triband and a quad band BPF where the input/output coupling circuit is modified to extract the higher order modes. Two stub loaded resonators are also embedded to improve the passband selectivity and to improve upper stopband characteristics. The design guidelines are demonstrated through the external quality factor (Qe) and coupling coefficient (k) synthesis approach. The developed filters are fabricated and measured to verify the predicted and simulated results. A close agreement is observed between them. The fabricated multiband BPFs has a very compact size, less insertion loss and good return loss profile.
- 10 August 2021
- Published by Hindawi Limited in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 31 (11) , e22853
A quint mode fractal architecture based resonator and its efficacy in the design of multiband bandpass filters
This paper presents a new approach to design multiband bandpass filters (BPF) using multimode resonator topology inspired from Bamileke fractal architecture in the form of fractal shaped resonator. The proposed resonator architecture exhibits quint mode resonance behavior where resonance frequencies are determined using ABCD matrix. It offers flexibility in terms of choosing passband center frequencies precisely. Initially a second order dual band BPF is presented by suppressing higher order modes using asymmetric feed line. The same structure is used further to implement a triband and a quad band BPF where the input/output coupling circuit is modified to extract the higher order modes. Two stub loaded resonators are also embedded to improve the passband selectivity and to improve upper stopband characteristics. The design guidelines are demonstrated through the external quality factor (Qe) and coupling coefficient (k) synthesis approach. The developed filters are fabricated and measured to verify the predicted and simulated results. A close agreement is observed between them. The fabricated multiband BPFs has a very compact size, less insertion loss and good return loss profile.
- 11 April 2021
- Published by Springer Nature
- p. 505-514
A Compact Dual-Band Reconfigurable Filtering Antenna Using PIN Diode
- 11 April 2021
- Published by Springer Nature
- p. 505-514
A Compact Dual-Band Reconfigurable Filtering Antenna Using PIN Diode
- 11 April 2021
- Published by Springer Nature
- p. 515-522
Varactor-Loaded Tunable SIW Filter with Wide Upper Stopband Characteristic
- 11 April 2021
- Published by Springer Nature
- p. 515-522
Varactor-Loaded Tunable SIW Filter with Wide Upper Stopband Characteristic
- 26 January 2021
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 13 (5) , 442-446
A Pythagorean tree fractal shape stub-loaded resonator as a UWB bandpass filter with wide stopband
A compact ultrawideband (UWB) bandpass filter (BPF) is designed by harnessing the efficacy of a Pythagorean tree fractal shape stub-loaded resonator. The design inherently provides the passband transmission poles, which make it convenient to be used in wide passband filtering circuits. The number and the position of the resonating modes can be controlled by increasing the iterations of the Pythagorean tree, as analyzed using odd- and even-mode analysis. Design steps of the BPF are detailed. The designed UWB BPF takes up a small circuit area of (12.13 × 9.59) mm2. The proposed design is fabricated and measured to verify the simulated results. The stopband is extended up to 17.5 GHz with a maximum attenuation of 15 dB.
- 26 January 2021
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 13 (5) , 442-446
A Pythagorean tree fractal shape stub-loaded resonator as a UWB bandpass filter with wide stopband
A compact ultrawideband (UWB) bandpass filter (BPF) is designed by harnessing the efficacy of a Pythagorean tree fractal shape stub-loaded resonator. The design inherently provides the passband transmission poles, which make it convenient to be used in wide passband filtering circuits. The number and the position of the resonating modes can be controlled by increasing the iterations of the Pythagorean tree, as analyzed using odd- and even-mode analysis. Design steps of the BPF are detailed. The designed UWB BPF takes up a small circuit area of (12.13 × 9.59) mm2. The proposed design is fabricated and measured to verify the simulated results. The stopband is extended up to 17.5 GHz with a maximum attenuation of 15 dB.
- 29 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (6) , 1892-1896
A Dual Function Reconfigurable Bandpass Filter for Wideband and Tri-Band Operations
A dual-functional reconfigurable filter is explored for the application in wideband and triple band band pass filter. The wideband configuration is implemented by parallel combination of open stub loaded and short circuited stub loaded resonators to exhibit a passband from 2.0 GHz-6.1 GHz. Tight coupling generates transmission zeroes at the either side of passband, which enhances the selectivity. The proposed tri-band BPF offers passbands at 2.4 GHz, 3.5 GHz and 5.2 GHz where two-stepped impedance resonators (SIRs) and one uniform impedance resonator (UIR) are assembled to accomplish such behavior. The two short circuited stubs are connected to the feed line to extend the range of upper stopband. PIN diodes are effectively utilized to switch the operation from wideband to tri-band or vice versa. Detailed design guidelines are provided to design the proposed filter. The behavior of the proposed filter topology is investigated by even and odd mode analysis. The developed reconfigurable filter is fabricated and measured to verify the anticipated and simulated results. A close agreement is observed between them. The fabricated reconfigurable BPF has a very compact size, high selectivity, less insertion loss and good return loss profile.
- 29 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (6) , 1892-1896
A Dual Function Reconfigurable Bandpass Filter for Wideband and Tri-Band Operations
A dual-functional reconfigurable filter is explored for the application in wideband and triple band band pass filter. The wideband configuration is implemented by parallel combination of open stub loaded and short circuited stub loaded resonators to exhibit a passband from 2.0 GHz-6.1 GHz. Tight coupling generates transmission zeroes at the either side of passband, which enhances the selectivity. The proposed tri-band BPF offers passbands at 2.4 GHz, 3.5 GHz and 5.2 GHz where two-stepped impedance resonators (SIRs) and one uniform impedance resonator (UIR) are assembled to accomplish such behavior. The two short circuited stubs are connected to the feed line to extend the range of upper stopband. PIN diodes are effectively utilized to switch the operation from wideband to tri-band or vice versa. Detailed design guidelines are provided to design the proposed filter. The behavior of the proposed filter topology is investigated by even and odd mode analysis. The developed reconfigurable filter is fabricated and measured to verify the anticipated and simulated results. A close agreement is observed between them. The fabricated reconfigurable BPF has a very compact size, high selectivity, less insertion loss and good return loss profile.