Miao Yu
Miao Yu has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Anjian Zhou
Chongqing Changan New Energy Automobile Technology Company Ltd., Chongqing, China
1 shared publication - Bo Li
School of Automotive Engineering, Chongqing University, Chongqing 400044, China
1 shared publication - Chunyun Fu
College of Mechanical and Vehicle Engineering Chongqing University Chongqing China
1 shared publication - Cunxue Wu
Chongqing Chang’an New Energy Vehicle Technology Co, Ltd., Chongqing 401120, China
1 shared publication - Datong Qin
Chongqing University
1 shared publication - Jintao Zheng
School of Automotive Engineering, Chongqing University, Chongqing 400044, China
1 shared publication
Latest Publications
- 5 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 68 (11) , 10504-10517
Analysis and Optimization of a Novel Power-Split Hybrid Powertrain
Plug-in Hybrid Electric Vehicles have advantages of both traditional fuel cars and Electric Vehicles. This paper presents a single planetary gear dual mode (input- and output-split) hybrid powertrain. Clutches are substituted for a synchronizer to achieve mode switch. In order to filter the six possible topology schemes, a screening method based on kinematics and theoretical efficiency analysis is utilized. Then a backward model is established by modeling each powertrain component and designing an appropriate control strategy. Finally, a backward simulation method is utilized to select the best topologies. In order to evaluate the performance of the proposed powertrain, two typical power-split powertrains, THS-P610 and Volt-II, are compared with the selected schemes. The comparison results show that the proposed powertrain, a simpler structure than Volt-II, improves the acceleration and fuel economy performances compared with THS-P610 and Volt-II.
- 5 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 68 (11) , 10504-10517
Analysis and Optimization of a Novel Power-Split Hybrid Powertrain
Plug-in Hybrid Electric Vehicles have advantages of both traditional fuel cars and Electric Vehicles. This paper presents a single planetary gear dual mode (input- and output-split) hybrid powertrain. Clutches are substituted for a synchronizer to achieve mode switch. In order to filter the six possible topology schemes, a screening method based on kinematics and theoretical efficiency analysis is utilized. Then a backward model is established by modeling each powertrain component and designing an appropriate control strategy. Finally, a backward simulation method is utilized to select the best topologies. In order to evaluate the performance of the proposed powertrain, two typical power-split powertrains, THS-P610 and Volt-II, are compared with the selected schemes. The comparison results show that the proposed powertrain, a simpler structure than Volt-II, improves the acceleration and fuel economy performances compared with THS-P610 and Volt-II.
- Open Access
Heat Pipe Thermal Management Based on High-Rate Discharge and Pulse Cycle Tests for Lithium-Ion Batteries
A battery thermal management system (BTMS) ensures that batteries operate efficiently within a suitable temperature range and maintains the temperature uniformity across the battery. A strict requirement of the BTMS is that increases in the battery discharge rate necessitate an increased battery heat dissipation. The advantages of heat pipes (HPs) include a high thermal conductivity, flexibility, and small size, which can be utilized in BTMSs. This paper experimentally examines a BTMS using HPs in combination with an aluminum plate to increase the uniformity in the surface temperature of the battery. The examined system with high discharge rates of 50, 75, and 100 A is used to determine its effects on the system temperature. The results are compared with those for HPs without fins and in ambient conditions. At a 100 A discharge current, the increase in battery temperature using the heat pipe with fins (HPWF) method is 4.8 °C lower than for natural convection, and the maximum temperature difference between the battery surfaces is 1.7 °C and 6.0 °C. The pulse circulation experiment was designed considering that the battery operates with a pulse discharge and temperature hysteresis. The depth of discharge is also considered, and the states-of-charge (SOC) values were 0.2, 0.5, and 0.8. The results of the two heat dissipation methods are compared, and the optimal heat dissipation structure is obtained by analyzing the experimental results. The results show that when the ambient temperature is 37 °C, differences in the SOC do not affect the battery temperature. In addition, the HPWF, HP, and natural convection methods reached stable temperatures of 40.8, 44.3, and the 48.1 °C, respectively the high temperature exceeded the battery operating temperature range.
Open AccessHeat Pipe Thermal Management Based on High-Rate Discharge and Pulse Cycle Tests for Lithium-Ion Batteries
A battery thermal management system (BTMS) ensures that batteries operate efficiently within a suitable temperature range and maintains the temperature uniformity across the battery. A strict requirement of the BTMS is that increases in the battery discharge rate necessitate an increased battery heat dissipation. The advantages of heat pipes (HPs) include a high thermal conductivity, flexibility, and small size, which can be utilized in BTMSs. This paper experimentally examines a BTMS using HPs in combination with an aluminum plate to increase the uniformity in the surface temperature of the battery. The examined system with high discharge rates of 50, 75, and 100 A is used to determine its effects on the system temperature. The results are compared with those for HPs without fins and in ambient conditions. At a 100 A discharge current, the increase in battery temperature using the heat pipe with fins (HPWF) method is 4.8 °C lower than for natural convection, and the maximum temperature difference between the battery surfaces is 1.7 °C and 6.0 °C. The pulse circulation experiment was designed considering that the battery operates with a pulse discharge and temperature hysteresis. The depth of discharge is also considered, and the states-of-charge (SOC) values were 0.2, 0.5, and 0.8. The results of the two heat dissipation methods are compared, and the optimal heat dissipation structure is obtained by analyzing the experimental results. The results show that when the ambient temperature is 37 °C, differences in the SOC do not affect the battery temperature. In addition, the HPWF, HP, and natural convection methods reached stable temperatures of 40.8, 44.3, and the 48.1 °C, respectively the high temperature exceeded the battery operating temperature range.