ASAnastassiya Semenova

Anastassiya Semenova

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Anastassiya Semenova has a total of 39 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Deep Copper Recovery from Autogenous Smelting Slags under Strongly Reducing Conditions

    by D.KH. Altybayeva, B.K. Kenzhaliyev, S.A. Kvyatkovskiy, M.A. Dyussebekova, B.E. Abdikerim, A.S. Semenova, A. Gemeal

    Deep reduction of copper smelting slags is a promising route to recover entrained non-ferrous metals and to generate slags suitable for further processing. This work investigates the depletion of fayalite–magnetite slags formed during autogenous smelting of copper concentrates in conditions simulating the oxidation and reduction zones of a two-zone Vanyukov furnace. Laboratory charges of 100 g, containing 14.63–16.82 wt.% Cu, 25.6–27.6 wt.% Fe, 30 wt.% S and 15 wt.% SiO₂, were smelted at 1350 °C with controlled oxygen injection to produce slags containing 0.93–1.54 wt.% Cu, 30.05–32.30 wt.% SiO₂ and 7.8–9.8 wt.% Fe₃O₄. Subsequent reduction at 1300 °C was carried out with activated carbon in a fivefold stoichiometric excess relative to magnetite, at an oxygen-containing blast flow rate of 5 L/h and a 1 h holding time. Chemical analysis shows that Fe₃O₄ in slag decreases from 7.8–7.95 wt.% to 2.5–2.6 wt.%, while copper content drops from 0.93–1.033 wt.% to 0.43–0.50 wt.% under oxygen partial pressures of 10⁻¹²–10⁻¹¹ atm. X-ray diffraction and electron microscopic studies reveal a transition from fayalite–magnetite slags with dispersed metallic copper and sulfides to fayalite-dominated matrices containing ferruginous sphalerite, copper minerals of the bornite–chalcopyrite type, iron oxides and glassy phases. Simultaneous thermal analysis demonstrates that all major endothermic and exothermic events are completed by 1300 °C, supporting this as an optimal temperature for deep slag depletion. The results define an operating window—slag composition, temperature, reductant dosage and pO₂—under which copper losses to slag can be reduced to about 0.5 wt.% in industrially relevant fayalite slags.

  • Open Access

    Toward Gold Recovery from Refractory Primary Ore by Cyanide-Free Direct Smelting with Copper Sulfide Concentrate

    by Sergey Kvyatkovskiy, Sultanbek Kozhakhmetov, Anastassiya Semenova, Bulat Sukurov, Maral Dyussebekova

    Refractory gold ores containing arsenic are difficult to process using conventional beneficiation and cyanide-leaching technologies. They often have a relatively low content of silicon dioxide (no more than 60%) and also contain arsenic. Therefore, they are difficult to use as fluxes in pyrometallurgical production and require separate processing. A technology based on the reduction pyrometallurgical selection process (RPS process) involves direct smelting. The feasibility of direct smelting of highly refractory primary gold ore with the addition of 5–10% sulfide copper concentrates was investigated. Smelting was conducted at temperatures of 1350–1400 °C under a reducing atmosphere. The resulting matte contained up to 100 g/t gold, while the slags produced contained less than 0.1 g/t gold. Gold recovery into the matte exceeded 98%. The gas purification scheme helps to prevent the release of sulfur dioxide and arsenic into the environment. The obtained matte can be processed at copper smelting plants in either solid or liquid form, with copper and noble metals recovered via the standard processing route: converting → fire refining → electrolytic refining → processing of copper electrolytic slimes for noble metal recovery.

  • Open Access

    Specific Features of Using High-Silica Flux Ore in Copper Smelting Units

    by Bagdaulet Kenzhaliyev, Sergey Kvyatkovskiy, Sultanbek Kozhakhmetov, Bulat Sukurov, Maral Dyussebekova, Anastassiya Semenova

    This study explores the application of high-silica flux ore in copper smelting and converting processes at the Zhezkazgan Copper Smelting plant. Pilot-scale experiments and SEM analyses were performed to assess its influence on slag composition, temperature regime, and metal recovery. The results demonstrated that replacing conventional flux with high-silica ore reduced flux consumption by 19%, increased converter slag temperature from 1124 to 1174 °C, and decreased copper content in converter slag from 10% to 4.5%. SEM micro-analysis revealed the formation of lead-containing silicate rims around matte inclusions, which hinder their settling at low temperatures. However, when the slag temperature exceeded 1400 °C, these rims were destroyed, facilitating separation and reducing residual copper. These findings highlight the potential of high-silica fluxes (>90% SiO2) to improve both energy efficiency and metal recovery in process of copper matte converting, offering practical recommendations for industrial operations.

  • Hydrothermal treatment of sinters containing thiosalts of non-ferrous metals

    by Institute of Metallurgy and Ore Beneficiation JSC, S.A. Kvyatkovskiy, Satbayev University, S.M. Kozhakhmetov, Institute of Metallurgy and Ore Beneficiation JSC; Satbayev University, A.S. Semenova, M.A. Dyussebekova, A.A. Shakhalov, Kazakhmys Corporation LLP

    Preliminary experiments have shown that the solution to the environmental problem of recycling copper-electrolyte smelting slags is by sulfidization followed by leaching and subsequent separation of selenium, tellurium, arsenic, and antimony from the solution. The first operation of this technology, which provides high selectivity, is sintering. The results obtained indicate the formation of metal thiosalts during sintering in the presence of sodium sulfate and carbonate and a reducing agent at a temperature of 800 0C. An increase in temperature leads to the melting of individual components of the charge and a slowdown in the process of sulfidization of slag components. At lower temperatures, a decrease in the activity of the charge components is observed. The optimal addition of Na2SO4 was 27 % of the slag weight, and Na2CO3 - 8.5 % of the slag weight. Reducing agent consumption is 27 % of the slag weight, sintering time is 2 hours. The optimal parameters for leaching the resulting cakes are temperature 90 0C, L:S ratio = 3:1, leaching duration 2 hours, and sodium sulfide concentration 2 mol/l. The best results for cake melting from cake leaching are temperature 1200 0C, heating rate 10 0C/min, and holding time 30 minutes. Charge composition: cake, 30 % soda ash by weight of cake, 11 % activated carbon. During the smelting, a metallized phase was obtained, consisting mainly of lead (90-91 %), and slag was obtained with a residual content of lead and copper of no more than 0.5 %.


  • Open Access

    Structural Changes in Copper Slags During Slow Cooling

    by Bulat Sukurov, Sergey Kvyatkovskiy, Sultanbek Kozhakhmetov, Anastassiya Semenova, Maral Dyussebekova, Marina Kvyatkovskaya

    The objects of the study were converter slags from the Balkhash copper plant in their initial state and after heat treatment. Using mineralogical and X-ray phase analysis, scanning electron microscopy (SEM), and electron probe microanalysis (EPMA), it was found that the initial converter slag and its thermally treated samples have identical matrices with almost complete coincidence in mineral and phase compositions. The distinguishing feature is the quantitative ratio of mineral components in the slag mass. Almost all of the iron is oxidized and present in the form of fayalite, magnetite, and magnetite, with other elements (silicon, copper, zinc, and aluminum) incorporated into its lattice. The structure of all slag samples indicates an association of sulfur exclusively with copper. Copper in the slags was identified in both metallic and sulfide forms. Slow cooling of the converter slag after its remelting contributes to the reduction in the sulfide–metal suspension in the volume of the melt and its coarsening. During slow cooling, structural changes occur not only in the main oxide part of the slag but also in the polymetallic globules.


  • Open Access

    Slag after Smelting of Anode Mud: Role of Sulphiding Sintering

    by Lyudmila Sokolovskaya, Sergey Kvyatkovskiy, Sultanbek Kozhakhmetov, Anastassiya Semenova, Bulat Sukurov, Maral Dyussebekova, Alexander Shakhalov

    The study object was slag from the Balkhash copper smelter, obtained by re-melting anode mud containing nonferrous metals. The process flow for processing these slags includes sintering with Na2SO4, Na2CO3, and coal, followed by soda-alkaline leaching of the sinter and extraction of metals from the solution into marketable products. Since sintering is the main operation providing high selectivity, the composition of the products of this process was studied. The main transformations during sintering were determined, and the optimal parameters were identified. The structures of slags and sintered materials obtained during the experiments were studied by electron-probe microanalysis. Sintering was performed at 600–800 °C. The best results for sulphidization of slag components were obtained at 800 °C; a further increase in temperature leads to the smelting of sinter particles and slows down sulphidization. The optimal quantities of additives, based on the weight of the slag, are Na2SO4—45%, Na2CO3—15%, and reducing agent—41%, with a sintering time of 2 h. These conditions enable the sulphidization of non-ferrous metals in the slag to the entire depth of the polymetallic globules. The distinct concentration of harmful impurities (Ni, As, and Sb) was observed in the fine structure of the polymetallic globules.


  • Open Access

    Study of the Effect of Fluxing Ability of Flux Ores on Minimizing of Copper Losses with Slags during Copper Concentrate Smelting

    by Maral Dyussebekova, Bagdaulet Kenzhaliyev, Sergey Kvyatkovskiy, Sultanbek Kozhakhmetov, Anastasiya Semenova, Bulat Sukurov

    The article describes the effect of the fluxing ability (FA) of ores used as a flux on slag formation and copper losses. In Kazakhstan, at the Balkhash copper smelting plant (BCSP), currently used fluxes have a very low SiO2 content—about 62%—whereas the Al2O3 content is 12%. Its fluxing ability (FA) was estimated, and it was shown that currently used silica fluxes have an exceedingly low FA. Only half of the fluxes participate in the slag formation. To obtain slags with a low magnetite concentration, a considerable surplus of flux must be added, which will result in a sharp reduction in its melt temperature, increased slag output, and therefore copper losses. The slag structure was studied by means of scanning electron microscopy and electron probe microanalysis (EPMA). To determine one of the primary causes of flux ores’ low FA, it is necessary to use the microstructural pattern of experimental samples.


  • Analysis of Existing Technologies for Depletion of Dump Slags of Autogenous Melting

    by “Institute of Metallurgy and Ore Beneficiation” JSC, B.K. Kenzhaliyev, S.A. Kvyatkovskiy, M.A. Dyussebekova, A.S. Semenova, D. Nurhadiyanto

    Pyro-metallurgy of copper production is characterized by the output of copper slag, which is regarded as a kind of solid waste. Moreover, this slag is identified as hazardous because it contains impurities, like Pb, As, and Cu. Obtaining dump slags in autogenous processes does not always meet the requirements of effective technologies, most often slags contain more than 1.0% of copper and need to be depleted. This work is presented a brief analysis of existing technologies used for copper slag depletion. The analysis of the existing technologies for the depletion of autogenous smelting dump slags showed that the most promising option seems to be the depletion of copper slags in one PV unit since by improving the process itself, by changing the unit design, it is possible to achieve technologically complete production of matte and dump slag with low copper content. There were proposed two technologies of improvement: electro-heating of slag siphon using the graphite electrodes and depletion process in two-zone PV furnace.


  • Effect of Reducing Agent on Structure and Thermal Properties of Autogenous Copper Sulfide Concentrate Smelting Slags

    by L. V. Sokolovskaya, S. A. Kvyatkovskiy, S. M. Kozhakhmetov, A. S. Semenova, R. S. Seisembayev


  • Extraction of Gold from Refractory Gold-Bearing Ores by Means of Reducing Pyrometallurgical Selection

    by R. S. Seisembayev, S. M. Kozhakhmetov, S. A. Kvyatkovsky, A. S. Semenova