Alan C. Gray
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alan C. Gray has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
Corin B. E. Gawith
University of Southampton
7 shared publicationsPeter G. R. Smith
University of Southampton
7 shared publications- James Christopher Gates
Optoelectronics Research Centre, University of Southampton, Southampton, UK
5 shared publications - Lewis G. Carpenter
American Institute for Manufacturing Integrated Photonics
5 shared publications - Sam A. Berry
Optoelectronics Research Centre, University of Southampton, Southampton, SO17 1BJ, UK
5 shared publications - Christopher Holmes
Optoelectronics Research Centre, University of Southampton, Southampton, UK
3 shared publications
Latest Publications
- Open Access
- 29 March 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (8) , 12427-12439
Short single-frequency self-pulsing Brillouin-Raman distributed feedback fiber laser
We demonstrate that the stimulated Brillouin scattering of a 250 mm long distributed feedback Raman fiber laser can self-pulse with repetition rates up to 7 MHz, pulse widths of 25 ns, and peak powers of 1.2 W. While both CW and pulsed lasing are produced from a bespoke grating at 1119 nm this laser design could be constructed at almost any wavelength, as the Raman and Brillouin gain regions are relative to the pump wavelength. The laser has a low lasing threshold for a Raman laser of 0.55 W, a peak slope efficiency of 14 %, and a maximum average output of 0.25 W. An investigation of beating between pure Raman and Raman-pumped Brillouin lasing shows that the outputs of the two processes are highly correlated and thus the Brillouin lasing is essentially single-frequency when CW and near transform limited for pulsed operation. A phenomenological model of the Raman-Brillouin interaction shows that the pulsing behaviour of such a cavity is expected and produces very similar pulsing to that the seen in experimental results.
- 29 March 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (8) , 12427-12439
Open AccessShort single-frequency self-pulsing Brillouin-Raman distributed feedback fiber laser
We demonstrate that the stimulated Brillouin scattering of a 250 mm long distributed feedback Raman fiber laser can self-pulse with repetition rates up to 7 MHz, pulse widths of 25 ns, and peak powers of 1.2 W. While both CW and pulsed lasing are produced from a bespoke grating at 1119 nm this laser design could be constructed at almost any wavelength, as the Raman and Brillouin gain regions are relative to the pump wavelength. The laser has a low lasing threshold for a Raman laser of 0.55 W, a peak slope efficiency of 14 %, and a maximum average output of 0.25 W. An investigation of beating between pure Raman and Raman-pumped Brillouin lasing shows that the outputs of the two processes are highly correlated and thus the Brillouin lasing is essentially single-frequency when CW and near transform limited for pulsed operation. A phenomenological model of the Raman-Brillouin interaction shows that the pulsing behaviour of such a cavity is expected and produces very similar pulsing to that the seen in experimental results.
- 18 January 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (3) , 676-680
High power 739 nm VECSELs for future Yb+ ion cooling
We present an operational characterization of a vertical-external-cavity surface-emitting laser emitting around 739 nm with over 150 mW in a single fundamental spatial mode. Results show that the laser is capable of oscillating on a single cavity axial mode at 740 nm for up to 22 mW. Tuning of the optical emission is shown to reach 737.3 nm. Furthermore, at best performance, the laser exhibits a slope efficiency of 8.3% and a threshold power of 1.27 W for an output coupler reflectivity of 98%.
- 18 January 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (3) , 676-680
High power 739 nm VECSELs for future Yb+ ion cooling
We present an operational characterization of a vertical-external-cavity surface-emitting laser emitting around 739 nm with over 150 mW in a single fundamental spatial mode. Results show that the laser is capable of oscillating on a single cavity axial mode at 740 nm for up to 22 mW. Tuning of the optical emission is shown to reach 737.3 nm. Furthermore, at best performance, the laser exhibits a slope efficiency of 8.3% and a threshold power of 1.27 W for an output coupler reflectivity of 98%.
- Open Access
- 28 October 2020
- Published by Optica Publishing Group in Optics Express
- Vol. 28 (23) , 34279-34289
Upconversion detection of 1.25 Gb/s mid-infrared telecommunications using a silicon avalanche photodiode
With an ever-increasing interest in secure and reliable free-space optical communication, upconversion detectors enabled through nonlinear optical processes are an attractive route to transmitting data as a mid-infrared signal. This spectral region is known to have a higher transmissivity through the atmosphere. In this work, we present an upconversion scheme for detection in the silicon absorption band using magnesium-oxide doped periodically poled lithium niobate to generate 21 mW of a 3.4 µm signal from commercial laser sources using a difference frequency generation process. Following a further nonlinear frequency conversion, via sum-frequency generation, the resulting signal at 809 nm is detected. We achieve >50 µW of signal and bit error rates of 10−7 from a single-pass nonlinear conversion for both the transmitter and receiver systems without the need for additional optical amplifiers at the receiving end. The error rates due to potentially reduced laser powers at the receiver end are investigated and laser noise transfer through our system is discussed.
- 28 October 2020
- Published by Optica Publishing Group in Optics Express
- Vol. 28 (23) , 34279-34289
Open AccessUpconversion detection of 1.25 Gb/s mid-infrared telecommunications using a silicon avalanche photodiode
With an ever-increasing interest in secure and reliable free-space optical communication, upconversion detectors enabled through nonlinear optical processes are an attractive route to transmitting data as a mid-infrared signal. This spectral region is known to have a higher transmissivity through the atmosphere. In this work, we present an upconversion scheme for detection in the silicon absorption band using magnesium-oxide doped periodically poled lithium niobate to generate 21 mW of a 3.4 µm signal from commercial laser sources using a difference frequency generation process. Following a further nonlinear frequency conversion, via sum-frequency generation, the resulting signal at 809 nm is detected. We achieve >50 µW of signal and bit error rates of 10−7 from a single-pass nonlinear conversion for both the transmitter and receiver systems without the need for additional optical amplifiers at the receiving end. The error rates due to potentially reduced laser powers at the receiver end are investigated and laser noise transfer through our system is discussed.
- Open Access
- 7 July 2020
- Published by Optica Publishing Group in Optics Express
- Vol. 28 (15) , 21382-21390
CW demonstration of SHG spectral narrowing in a PPLN waveguide generating 2.5 W at 780 nm
Periodically poled lithium niobate (PPLN) waveguides are a proven and popular means for efficient wavelength conversion. However, conventional PPLN waveguides typically have small mode field diameters (MFD) (≲6 µm) or significant insertion and/or propagation losses, limiting their ability to operate at multi-watt power levels. In this work we utilise zinc indiffused PPLN ridge waveguides that have a larger MFD, favourable pump/SHG modal overlap, and low insertion losses. Here for the first time, we have demonstrated continuous wave (CW) spectral narrowing from a PPLN waveguide, both with high efficiency and multi-watt second harmonic generation (SHG). 2.5 W of 780 nm has been produced by SHG of an amplified 1560 nm telecom laser with a device efficiency of 58% in a 4.0-cm long ridge waveguide. We have modelled conversion efficiency and applied experimentally measured waveguide parameters to show excellent agreement to the SHG spectra. Spectral narrowing of the full width half maximum (FWHM) of 35.7% has been measured as the nonlinear drive is increased. This work demonstrates that single-pass, multi-watt, CW SHG at 780 nm is feasible from our PPLN waveguide in the large conversion regime.
- 7 July 2020
- Published by Optica Publishing Group in Optics Express
- Vol. 28 (15) , 21382-21390
Open AccessCW demonstration of SHG spectral narrowing in a PPLN waveguide generating 2.5 W at 780 nm
Periodically poled lithium niobate (PPLN) waveguides are a proven and popular means for efficient wavelength conversion. However, conventional PPLN waveguides typically have small mode field diameters (MFD) (≲6 µm) or significant insertion and/or propagation losses, limiting their ability to operate at multi-watt power levels. In this work we utilise zinc indiffused PPLN ridge waveguides that have a larger MFD, favourable pump/SHG modal overlap, and low insertion losses. Here for the first time, we have demonstrated continuous wave (CW) spectral narrowing from a PPLN waveguide, both with high efficiency and multi-watt second harmonic generation (SHG). 2.5 W of 780 nm has been produced by SHG of an amplified 1560 nm telecom laser with a device efficiency of 58% in a 4.0-cm long ridge waveguide. We have modelled conversion efficiency and applied experimentally measured waveguide parameters to show excellent agreement to the SHG spectra. Spectral narrowing of the full width half maximum (FWHM) of 35.7% has been measured as the nonlinear drive is increased. This work demonstrates that single-pass, multi-watt, CW SHG at 780 nm is feasible from our PPLN waveguide in the large conversion regime.
- Open Access
- 27 May 2020
- Published by Optica Publishing Group in Applied Optics
- Vol. 59 (16) , 4921-4926
Zinc-indiffused MgO:PPLN waveguides for blue/UV generation via VECSEL pumping
We present the design and characterization of a zinc-indiffused periodically poled lithium-niobate ridge waveguide for second-harmonic generation of ∼ 390 n m light from 780 nm. We use a newly developed, broadband near-infrared vertical external-cavity surface-emitting laser (VECSEL) to investigate the potential for lower-footprint nonlinear optical pump sources as an alternative to larger commercial laser systems. We demonstrate a VECSEL with an output power of 500 mW, containing an intracavity birefringent filter for spectral narrowing and wavelength selection. In this first demonstration of using a VECSEL to pump a nonlinear waveguide, we present the ability to generate 1 mW of ∼ 390 n m light with further potential for increased efficiency and size reduction.
- 27 May 2020
- Published by Optica Publishing Group in Applied Optics
- Vol. 59 (16) , 4921-4926
Open AccessZinc-indiffused MgO:PPLN waveguides for blue/UV generation via VECSEL pumping
We present the design and characterization of a zinc-indiffused periodically poled lithium-niobate ridge waveguide for second-harmonic generation of ∼ 390 n m light from 780 nm. We use a newly developed, broadband near-infrared vertical external-cavity surface-emitting laser (VECSEL) to investigate the potential for lower-footprint nonlinear optical pump sources as an alternative to larger commercial laser systems. We demonstrate a VECSEL with an output power of 500 mW, containing an intracavity birefringent filter for spectral narrowing and wavelength selection. In this first demonstration of using a VECSEL to pump a nonlinear waveguide, we present the ability to generate 1 mW of ∼ 390 n m light with further potential for increased efficiency and size reduction.
- Open Access
- 3 December 2019
- Published by Optica Publishing Group in OSA Continuum
- Vol. 2 (12) , 3456-3464
Zn-indiffused diced ridge waveguides in MgO:PPLN generating 1 watt 780 nm SHG at 70% efficiency
We present a metallic zinc indiffused diced ridge waveguide in magnesium doped periodically poled lithium niobate (MgO:PPLN) capable of generating over 1 W of 780 nm with 70% efficiency. Our 40 mm long waveguide has near circular fundamental mode output with diameter 10.4 µm and insertion loss of -1.17 dB. Using a commercial 2 W EDFA-based system, the SHG output power did not exhibit roll-off at maximum available pump power.
- 3 December 2019
- Published by Optica Publishing Group in OSA Continuum
- Vol. 2 (12) , 3456-3464
Open AccessZn-indiffused diced ridge waveguides in MgO:PPLN generating 1 watt 780 nm SHG at 70% efficiency
We present a metallic zinc indiffused diced ridge waveguide in magnesium doped periodically poled lithium niobate (MgO:PPLN) capable of generating over 1 W of 780 nm with 70% efficiency. Our 40 mm long waveguide has near circular fundamental mode output with diameter 10.4 µm and insertion loss of -1.17 dB. Using a commercial 2 W EDFA-based system, the SHG output power did not exhibit roll-off at maximum available pump power.
- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Mapping Water Contamination of Jet Fuel
We shall report the latest progress on AWESOME (Airbus Water Emulsification Sensor using Optical Monitoring Equipment), which seeks to use spectrally multiplexed guided and leaky mode Bragg gratings to quantify dissolved (5ppm-v resolution), free and emulsified water contamination at multiple physical points within a fuel tank.
- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Mapping Water Contamination of Jet Fuel
We shall report the latest progress on AWESOME (Airbus Water Emulsification Sensor using Optical Monitoring Equipment), which seeks to use spectrally multiplexed guided and leaky mode Bragg gratings to quantify dissolved (5ppm-v resolution), free and emulsified water contamination at multiple physical points within a fuel tank.
- Open Access
- 14 August 2019
- Published by Optica Publishing Group in Optics Express
- Vol. 27 (17) , 24538-+
ZnO indiffused MgO:PPLN ridge waveguides
We have demonstrated the first MgO:PPLN ridge waveguides based on ZnO indiffusion and dicing. The fabrication process utilizes ductile regime dicing of a planar waveguide layer producing second harmonic generation (SHG) devices with a near-symmetric sinc2 spectral profile, indicating highly uniform 40 mm long devices. A near circular pump mode is also obtained enabling efficient coupling to single mode telecommunication fibers. A conversion efficiency of 145%/W, for 1560-780 nm SHG, has been measured.
- 14 August 2019
- Published by Optica Publishing Group in Optics Express
- Vol. 27 (17) , 24538-+
Open AccessZnO indiffused MgO:PPLN ridge waveguides
We have demonstrated the first MgO:PPLN ridge waveguides based on ZnO indiffusion and dicing. The fabrication process utilizes ductile regime dicing of a planar waveguide layer producing second harmonic generation (SHG) devices with a near-symmetric sinc2 spectral profile, indicating highly uniform 40 mm long devices. A near circular pump mode is also obtained enabling efficient coupling to single mode telecommunication fibers. A conversion efficiency of 145%/W, for 1560-780 nm SHG, has been measured.
- Open Access
- 29 March 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (7) , 9155-9164
Leaky mode integrated optical fibre refractometer
A route to monitor external refractive indices greater than the core index of the waveguide is presented. Initial application utilizes an integrated optical fibre (IOF) platform due to its potential for use in harsh environment sensing. IOF is fabricated using a bespoke flame hydrolysis deposition process to fuse an optical fibre to a planar substrate achieving an optical quality, ruggedized glass layer between the fibre and substrate was fabricated. The presented refractometer is created by direct UV writing of multiple fibre Bragg gratings into an etched (22 μm diameter) optical fibre post fabrication. Linear regression analysis is applied to quantify propagation loss by monitoring each FBG’s back reflected power. The device operates with a sensitivity of approximately 350 dB/cm/RIU at a refractive index of 1.451 at 1550 nm. Numerical simulations using a transfer matrix method are presented and potential routes for development are discussed.
- 29 March 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (7) , 9155-9164
Open AccessLeaky mode integrated optical fibre refractometer
A route to monitor external refractive indices greater than the core index of the waveguide is presented. Initial application utilizes an integrated optical fibre (IOF) platform due to its potential for use in harsh environment sensing. IOF is fabricated using a bespoke flame hydrolysis deposition process to fuse an optical fibre to a planar substrate achieving an optical quality, ruggedized glass layer between the fibre and substrate was fabricated. The presented refractometer is created by direct UV writing of multiple fibre Bragg gratings into an etched (22 μm diameter) optical fibre post fabrication. Linear regression analysis is applied to quantify propagation loss by monitoring each FBG’s back reflected power. The device operates with a sensitivity of approximately 350 dB/cm/RIU at a refractive index of 1.451 at 1550 nm. Numerical simulations using a transfer matrix method are presented and potential routes for development are discussed.
- Open Access
- 9 February 2018
- Published by Optica Publishing Group in Optics Letters
- Vol. 43 (4) , 791-794
Evanescent field refractometry in planar optical fiber
This Letter demonstrates a refractometer in integrated optical fiber, a new optical platform that planarizes fiber using flame hydrolysis deposition (FHD). The unique advantage of the technology is survivability in harsh environments. The platform is mechanically robust, and can survive elevated temperatures approaching 1000°C and exposure to common solvents, including acetone, gasoline, and methanol. For the demonstrated refractometer, fabrication was achieved through wet etching an SMF-28 fiber to a diameter of 8 μm before FHD planarization. An external refractive index was monitored using fiber Bragg gratings (FBGs), written into the core of the planarized fiber. A direct comparison to alternative FBG refractometers is made, for which the developed platform is shown to have comparable sensitivity, with the added advantage of survivability in harsh environments.
- 9 February 2018
- Published by Optica Publishing Group in Optics Letters
- Vol. 43 (4) , 791-794
Open AccessEvanescent field refractometry in planar optical fiber
This Letter demonstrates a refractometer in integrated optical fiber, a new optical platform that planarizes fiber using flame hydrolysis deposition (FHD). The unique advantage of the technology is survivability in harsh environments. The platform is mechanically robust, and can survive elevated temperatures approaching 1000°C and exposure to common solvents, including acetone, gasoline, and methanol. For the demonstrated refractometer, fabrication was achieved through wet etching an SMF-28 fiber to a diameter of 8 μm before FHD planarization. An external refractive index was monitored using fiber Bragg gratings (FBGs), written into the core of the planarized fiber. A direct comparison to alternative FBG refractometers is made, for which the developed platform is shown to have comparable sensitivity, with the added advantage of survivability in harsh environments.