Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Raúl Rivera-Blas has a total of 47 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Analysis of energy consumption and pollutants in additive manufacturing: a comparison of ABS, PLA, and PETG by operational stages

    by Giancarlo Marchetta Cruz, Isaías Chamorro Cruz, Diego Jesus Garcia Cedillo, Francisco De Matías Aguilar, David Franco Martínez, Omar Ismael López Suárez, Raul Rivera Blas, Sergio Guillermo Torres Cedillo

  • Open Access

    Stable Thermal Regime in an Alkaline Water Electrolyser System

    by Eduardo Martínez-Zárate, Alejandro Wintergerst-Felipe, Irvin Daniel Rivas-Yreta, Israel Trujillo-Olivares, Rosa de Guadalupe González-Huerta, Luis Armando Flores-Herrera, Juan Manuel Sandoval-Pineda, Raúl Rivera-Blas

    Experimental alkaline water electrolysis (AWE) systems require precise thermal management to achieve stable electrochemical efficiency. Manual operation of laboratory-scale electrolysers often induces thermal fluctuations that lead to excessive overpotentials. In this work, a real-time data acquisition (DAQ) and automated temperature-control architecture were implemented in a 3 kW nominal alkaline electrolyser in order to observe the thermal stability regime. The system was evaluated using a stepped-current protocol derived from FCTESTNET standards. Current densities of 0.3 and 0.5 A·cm−2 were investigated, corresponding to operating currents of approximately 22.5 A and 40 A, respectively. Variations in manually controlled conditions raised temperature values to near 100 °C. With the implemented control system, two distinct thermal regimes were observed. At 0.3 A·cm−2, cyclic behaviour between 60 and 80 °C was recorded due to on–off cooling dynamics. At 0.5 A·cm−2, the system reached a stable thermal regime between 70 and 75 °C, maintaining steady-state fluctuations within ±1 °C after transient stabilisation. It was observed that the electronically controlled thermal system reduced temperature-induced overpotentials and improved voltage stability during long-duration tests. The results demonstrate that integrating automated thermal control enhances operational safety and enables reproducible electrolyser evaluation under controlled laboratory conditions.

  • Mechatronic Vehicle Design for Sanitary Sewer Cleaning Support in Mexico City

    by Miguel Angel Mendez-Salgado, Luis Armando Flores-Herrera, Raúl Rivera-Blas, Juan Manuel Sandoval-Pineda, Manuel Rivera-Tinoco, Alfonso Rosas-Escobedo

  • Hybrid Deep Learning Method for Computerized Quality Control for Automotive Parts Manufacturing

    by Víctor Vargas-Baeza, Luis Armando Flores-Herrera, Raúl Rivera-Blas, Nayeli Rodríguez-Contreras, Emmanuel Zenén Rivera-Blas

  • Open Access

    Impact of Electrode Support Internal Geometry on Polarisation Curve Performance in Alkaline Electrolysers

    by Alejandro Wintergerst-Felipe, Israel Trujillo-Olivares, Roberto Moreno-Soriano, Raúl Rivera-Blas, Luis Armando Flores-Herrera, Juan Manuel Sandoval-Pineda, Rosa de Guadalupe González-Huerta

    This study details the design, fabrication, and experimental validation of three unique alkaline electrolysers, each featuring a modified internal electrode-support geometry. Their performance was comprehensively assessed through polarisation curve analysis in individual, partial, and global configurations. The development followed the Advanced Product Quality Planning (APQP) methodology, employing pure nickel electrodes to ensure stability. The results demonstrate that specific geometric alterations directly influence electrochemical performance and overall efficiency. By operating three electrolysers simultaneously, the system achieved an overall efficiency of 42% and a maximum oxyhydrogen production rate of 10 L·min−1, with minimal electrolyte carryover. This systematic work establishes essential design guidelines to advance the technology from Technology Readiness Level (TRL) 5 to TRL 6, facilitating the development of a reliable 5 kW hydrogen production system.

  • Open Access

    Impact of Electrode Support Internal Geometry on Polarisation Curve Performance in Alkaline Electrolysers

    by Alejandro Wintergerst-Felipe, Israel Trujillo-Olivares, Roberto Moreno-Soriano, Raúl Rivera-Blas, Luis Armando Flores-Herrera, Juan Manuel Sandoval-Pineda, Rosa de Guadalupe Gonzalez-Huerta

    Alkaline electrolysers are a proven and cost-efficient technology for large-scale hydrogen production. While established, improving their performance remains an active research area. A significant but less recognized factor is the internal geometry of electrode supports, which influences gas removal and mass transport, thereby affecting efficiency. This study details the design, fabrication, and experimental validation of three unique alkaline electrolysers, each featuring a modified internal electrode-support geometry. Their performance was comprehensively assessed through polarization curve analysis in individual, partial, and global configurations. The development followed the Advanced Product Quality Planning (APQP) methodology, employing pure nickel electrodes for stability. The research experimentally demonstrates how specific geometric alterations directly influence electrochemical performance and overall efficiency. By operating three electrolysers simultaneously, the system achieved an overall efficiency of 42% and a maximum oxyhydrogen production rate of 10 L min-1 with minimal electrolyte carryover This systematic work establishes essential design guidelines aimed at advancing the technology from Technology Readiness Level (TRL) 5 to TRL 6, facilitating the development of a reliable 5 kW hydrogen production system.

  • Open Access

    High-Efficiency Biomass Burner for Forest By-Products

    by Artemio García-Flores, Juan Manuel Sandoval-Pineda, Luis Armando Flores-Herrera, Alejandro Zacarías-Santiago, René O. Vargas, Raúl Rivera-Blas

    This study employs CFD simulations carried on ANSYS Fluent 2022 R1 (ANSYS Inc., Canonsburg, PA, USA), to address the design, development, and thermodynamic analysis of a biomass burner, based on mass and energy balances, combustion efficiency, flame temperature, and thermodynamic properties. The prototype incorporates a flow deflector located before the combustion chamber. This component improves the air-fuel mixture to maximise thermal efficiency and minimise pollutant emissions. The burner is specifically designed to use sawdust as fuel and is intended for industrial applications such as heating or drying processes. The integration of the flow deflector results in uniform, complete combustion, achieving 90% thermal efficiency and an adjustable thermal power output of 0–100 kW. Compared to conventional burners, this design reduces CO emissions by 20% and NOx emissions by 15%, demonstrating significant environmental improvements. The design methodology is based on mass and energy balance equations to evaluate combustion efficiency as a function of the stoichiometric ratio, along with experimental testing. These experimental tests were conducted using an ECOM (America Ltd., Nashua, NH, USA) gas analyser and anemometer. The internal temperature was monitored with a K-type thermocouple (Omega Engineering Inc., Norwalk, CT, USA). The results confirmed the positive influence of the structural design on thermal performance. The proposed burner aims to maximise heat generation in the combustion chamber, offering an innovative alternative for biomass combustion systems.

  • Open Access

    A Comprehensive Analysis of Power Electromobility: Challenges from a PESTLE Perspective

    by Nicolay Andres Niño-Suarez, Luis Armando Flores-Herrera, Raúl Rivera-Blas, María Bárbara Calva-Yañez, Paola Andrea Niño-Suárez, Emmanuel Zenén Rivera-Blas, José Eduardo Hernández-Galindo, Oscar Alberto Alvarez-Flores

    This study analyses aspects related to the electromobility transition. Emerging technologies have enabled the production and commercialisation of electric vehicles to reduce polluting emissions. However, significant obstacles are present in this global transition. The analysis identifies that public policies play a crucial role in the development of electromobility, and emphasises how new business models in electromobility are emerging to satisfy changing customer demands. Concerns related to raw materials extraction, battery disposal, and vehicle-to-grid (V2G) integration are also important to consider. The relationship between technologically advanced countries and raw material-producing nations must balance socioeconomic, historical, labour, and ecological factors. In order to have a standard reference, this study considers for the analysis the political, economic, social, technological, environmental, and legal factors (PESTLE). An analysis of future scenarios considering pessimistic and optimistic trends revealed that, compared with the actual trends, important actions must be taken to develop electromobility not only from the technological aspect. These results provide a comprehensive analysis of electromobility sustainability and its importance for multidisciplinary stakeholders related to the actual challenges towards electromobility, the electric network capabilities, and the importance of creating new jobs and products based on a circular and sustainable economy.

  • Open Access

    e-Learning Challenges in STEM Education

    by María Magdalena Saldívar-Almorejo, Luis Armando Flores-Herrera, Raúl Rivera-Blas, Paola Andrea Niño-Suárez, Emmanuel Zenén Rivera-Blas, Nayeli Rodríguez-Contreras

    This work reviews the key challenges surrounding teaching Science, Technology, Engineering, and Mathematics subjects known as STEM. The research has uncovered a significant gap between traditional teaching styles and the need to develop and adapt to new remote-learning modalities. The work describes the technological, pedagogical, social, and institutional challenges, finally identifying the importance of their joint interaction. Since the COVID-19 pandemic, it has become evident that STEM educators must increase their awareness and knowledge of instructional models focused on using digital platforms. The current trend is centred on developing remote-learning tools, which will likely become the predominant learning norm as the economy’s viability increases. However, these remote-learning approaches must maintain interaction with the physical world, as understanding real-world phenomena is crucial for improving learning processes. STEM learning through e-learning will have a greater chance of success if academic institutions collaborate with other sectors of society, such as the business sector, to receive feedback for the continuous improvement of the proposed teaching methods.


  • Open Access

    A Novel Modified Discrete Differential Evolution Algorithm to Solve the Operations Sequencing Problem in CAPP Systems

    by Oscar Alberto Alvarez-Flores, Raúl Rivera-Blas, Luis Armando Flores-Herrera, Emmanuel Zenén Rivera-Blas, Miguel Angel Funes-Lora, Paola Andrea Niño-Suárez

    Operation Sequencing (OS) is one of the most critical tasks in a CAPP system. This process could be modelled as a combinatorial problem where finding a suitable solution within a reasonable time interval is difficult. This work implements a novel Discrete Differential Evolution Algorithm (DDEA) to solve the OS problem, focusing on parts of up to 76 machining operations; the relationships among operations are represented as a directed graph; the contributions of the DDEA are as follows: (1) operates with a discrete representation in the space of feasible solutions; (2) employs mutation and crossover operators to update solutions and to reduce machining and setup costs, (3) possess a local search strategy to achieve better solutions, and (4) integrates a statistical method based on quantiles to measure the quality and likelihood for an achieving a solution. To demonstrate the efficiency and robustness of the DDEA, five prismatic parts with different numbers of machining operations as benchmarks to address the OS problem were selected. The results generated the same OS for parts with a few machining operations (up to 23 machining operations). Conversely, for parts with more machining operations, the DDEA needs more runs to achieve the best solution.