Yuyao Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuyao Zhang has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Danning Kang
School of Materials Engineering, Shanghai University of Engineering Science, Shanghai 201620, China
2 shared publications - Jun Li
School of Materials Science and Engineering, Shanghai University of Engineering Science, Shanghai 201620, China
2 shared publications - Wenyao Li
School of Materials Engineering, Shanghai University of Engineering Science, Shanghai 201620, China
1 shared publication
Latest Publications
- Open Access
Effect of Ni Doping Content on Phase Transition and Electrochemical Performance of TiO2 Nanofibers Prepared by Electrospinning Applied for Lithium-Ion Battery Anodes
Titanium dioxide (TiO2), as a potential anode material applied for lithium-ion batteries (LIBs), is constrained due to its poor theoretical specific capacity (335 mAh·g−1) and low conductivity (10−7-10−9 S·cm−1). When compared to TiO2, NiO with a higher theoretical specific capacity (718 mAh·g−1) is regarded as an alternative dopant for improving the specific capacity of TiO2. The present investigations usually assemble TiO2 and NiO with a simple bilayer structure and without NiO that is immersed into the inner of TiO2, which cannot fully take advantage of NiO. Therefore, a new strategy was put forward to utilize the synergistic effect of TiO2 and NiO, namely doping NiO into the inner of TiO2. NiO-TiO2 was fabricated into the nanofibers with a higher specific surface area to further improve their electrochemical performance due to the transportation path being greatly shortened. NiO-TiO2 nanofibers are expected to replace of the commercialized anode material (graphite). In this work, a facile one-step electrospinning method, followed by annealing, was applied to synthesize the Ni-doped TiO2 nanofibers. The Ni doping content was proven to be a crucial factor affecting phase constituents, which further determined the electrochemical performance. When the Ni doping content was less than 3 wt.%, the contents of anatase and NiO were both increased, while the rutile content was decreased in the nanofibers. When the Ni doping content exceeded 3 wt.%, the opposite changes were observed. Hence, the optimum Ni doping content was determined as 3 wt.%, at which the highest weight fractions of anatase and NiO were obtained. Correspondingly, the obtained electronic conductivity of 4.92 × 10−5 S⋅cm−1 was also the highest, which was approximately 1.7 times that of pristine TiO2. The optimal electrochemical performance was also obtained. The initial discharge and charge specific capacity was 576 and 264 mAh·g−1 at a current density of 100 mA·g−1. The capacity retention reached 48% after 100 cycles, and the coulombic efficiency was about 100%. The average discharge specific capacity was 48 mAh·g−1 at a current density of 1000 mA·g−1. Approximately 65.8% of the initial discharge specific capacity was retained when the current density was recovered to 40 mA·g−1. These excellent electrochemical results revealed that Ni-doped TiO2 nanofibers could be considered to be promising anode materials for LIBs.
Open AccessEffect of Ni Doping Content on Phase Transition and Electrochemical Performance of TiO2 Nanofibers Prepared by Electrospinning Applied for Lithium-Ion Battery Anodes
Titanium dioxide (TiO2), as a potential anode material applied for lithium-ion batteries (LIBs), is constrained due to its poor theoretical specific capacity (335 mAh·g−1) and low conductivity (10−7-10−9 S·cm−1). When compared to TiO2, NiO with a higher theoretical specific capacity (718 mAh·g−1) is regarded as an alternative dopant for improving the specific capacity of TiO2. The present investigations usually assemble TiO2 and NiO with a simple bilayer structure and without NiO that is immersed into the inner of TiO2, which cannot fully take advantage of NiO. Therefore, a new strategy was put forward to utilize the synergistic effect of TiO2 and NiO, namely doping NiO into the inner of TiO2. NiO-TiO2 was fabricated into the nanofibers with a higher specific surface area to further improve their electrochemical performance due to the transportation path being greatly shortened. NiO-TiO2 nanofibers are expected to replace of the commercialized anode material (graphite). In this work, a facile one-step electrospinning method, followed by annealing, was applied to synthesize the Ni-doped TiO2 nanofibers. The Ni doping content was proven to be a crucial factor affecting phase constituents, which further determined the electrochemical performance. When the Ni doping content was less than 3 wt.%, the contents of anatase and NiO were both increased, while the rutile content was decreased in the nanofibers. When the Ni doping content exceeded 3 wt.%, the opposite changes were observed. Hence, the optimum Ni doping content was determined as 3 wt.%, at which the highest weight fractions of anatase and NiO were obtained. Correspondingly, the obtained electronic conductivity of 4.92 × 10−5 S⋅cm−1 was also the highest, which was approximately 1.7 times that of pristine TiO2. The optimal electrochemical performance was also obtained. The initial discharge and charge specific capacity was 576 and 264 mAh·g−1 at a current density of 100 mA·g−1. The capacity retention reached 48% after 100 cycles, and the coulombic efficiency was about 100%. The average discharge specific capacity was 48 mAh·g−1 at a current density of 1000 mA·g−1. Approximately 65.8% of the initial discharge specific capacity was retained when the current density was recovered to 40 mA·g−1. These excellent electrochemical results revealed that Ni-doped TiO2 nanofibers could be considered to be promising anode materials for LIBs.
- Open Access
Synthesis of One-Dimensional Mesoporous Ag Nanoparticles-Modified TiO2 Nanofibers by Electrospinning for Lithium Ion Batteries
TiO2 is regarded as a prospective electrode material owing to its excellent electrochemical properties such as the excellent cycling stability and the high safety. However, its low capacity and low electronic conductivity greatly restrict the further improvement in electrochemical performance. A new strategy was put forward to solve the above defects involved in TiO2 in which the low capacity was enhanced by nanomerization and porosity of TiO2, and the low electronic conductivity was improved by introducing Ag with a high conductivity. One-dimensional mesoporous Ag nanoparticles-embedded TiO2 nanofibers (Ag@TiO2 nanofibers) were successfully synthesized via a one-step electrospinning process combined with subsequent annealing treatment in this study. The microstructure and morphology of mesoporous TiO2@Ag nanofibers were confirmed by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and nitrogen adsorption–desorption. TiO2 nanofibers mainly consisted of a large amount of anatase TiO2, accompanied with traces of rutile TiO2. Ag nanoparticles were uniformly distributed throughout TiO2 nanofibers and promoted the transformation of TiO2 from the anatase to the rutile. The corresponding electrochemical performances are measured by galvanostatic charge-discharge, cycle stability, rate performance, cycle voltammetry, and electrochemical impedance spectroscopy measurements in this research, with pristine TiO2 nanofibers as the reference. The results indicated that the introduction of Ag nanoparticles into TiO2 nanofibers significantly improved the diffusion coefficient of Li ions (5.42 × 10−9 cm2⋅s−1 for pristine TiO2, 1.96 × 10−8 cm2⋅s−1 for Ag@TiO2), and the electronic conductivity of TiO2 (1.69 × 10−5 S⋅cm−1 for pristine TiO2, and 1.99 × 10−5 S⋅cm−1 for Ag@TiO2), based on which the comprehensive electrochemical performance were greatly enhanced. The coulombic efficiency of the Ag@TiO2 nanofibers electrode at the first three cycles was about 56%, 93%, and 96%, which was higher than that without Ag (48%, 66%, and 79%). The Ag@TiO2 nanofibers electrode exhibited a higher specific discharge capacity of about 128.23 mAh⋅g−1 when compared with that without Ag (72.76 mAh·g−1) after 100 cycles at 100 mA·g−1. With the current density sharply increased from 40 mA·g−1 to 1000 mA·g−1, the higher average discharge capacity of 56.35 mAh·g−1 was remained in the electrode with Ag, when compared with the electrode without Ag (average discharge capacity of about 12.14 mAh·g−1). When the current density was returned to 40 mA·g−1, 80.36% of the initial value was returned (about 162.25 mAh·g−1) in the electrode with Ag, which was evidently superior to that without Ag (about 86.50 mAh·g−1, only 55.42% of the initial value). One-dimensional mesoporous Ag@TiO2 nanofibers can be regarded as a potential and promising candidate as anode materials for lithium ion batteries.
Open AccessSynthesis of One-Dimensional Mesoporous Ag Nanoparticles-Modified TiO2 Nanofibers by Electrospinning for Lithium Ion Batteries
TiO2 is regarded as a prospective electrode material owing to its excellent electrochemical properties such as the excellent cycling stability and the high safety. However, its low capacity and low electronic conductivity greatly restrict the further improvement in electrochemical performance. A new strategy was put forward to solve the above defects involved in TiO2 in which the low capacity was enhanced by nanomerization and porosity of TiO2, and the low electronic conductivity was improved by introducing Ag with a high conductivity. One-dimensional mesoporous Ag nanoparticles-embedded TiO2 nanofibers (Ag@TiO2 nanofibers) were successfully synthesized via a one-step electrospinning process combined with subsequent annealing treatment in this study. The microstructure and morphology of mesoporous TiO2@Ag nanofibers were confirmed by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and nitrogen adsorption–desorption. TiO2 nanofibers mainly consisted of a large amount of anatase TiO2, accompanied with traces of rutile TiO2. Ag nanoparticles were uniformly distributed throughout TiO2 nanofibers and promoted the transformation of TiO2 from the anatase to the rutile. The corresponding electrochemical performances are measured by galvanostatic charge-discharge, cycle stability, rate performance, cycle voltammetry, and electrochemical impedance spectroscopy measurements in this research, with pristine TiO2 nanofibers as the reference. The results indicated that the introduction of Ag nanoparticles into TiO2 nanofibers significantly improved the diffusion coefficient of Li ions (5.42 × 10−9 cm2⋅s−1 for pristine TiO2, 1.96 × 10−8 cm2⋅s−1 for Ag@TiO2), and the electronic conductivity of TiO2 (1.69 × 10−5 S⋅cm−1 for pristine TiO2, and 1.99 × 10−5 S⋅cm−1 for Ag@TiO2), based on which the comprehensive electrochemical performance were greatly enhanced. The coulombic efficiency of the Ag@TiO2 nanofibers electrode at the first three cycles was about 56%, 93%, and 96%, which was higher than that without Ag (48%, 66%, and 79%). The Ag@TiO2 nanofibers electrode exhibited a higher specific discharge capacity of about 128.23 mAh⋅g−1 when compared with that without Ag (72.76 mAh·g−1) after 100 cycles at 100 mA·g−1. With the current density sharply increased from 40 mA·g−1 to 1000 mA·g−1, the higher average discharge capacity of 56.35 mAh·g−1 was remained in the electrode with Ag, when compared with the electrode without Ag (average discharge capacity of about 12.14 mAh·g−1). When the current density was returned to 40 mA·g−1, 80.36% of the initial value was returned (about 162.25 mAh·g−1) in the electrode with Ag, which was evidently superior to that without Ag (about 86.50 mAh·g−1, only 55.42% of the initial value). One-dimensional mesoporous Ag@TiO2 nanofibers can be regarded as a potential and promising candidate as anode materials for lithium ion batteries.