SKSaurabh Karwal

Saurabh Karwal

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Saurabh Karwal has a total of 40 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Addressing the Defects within the Gate Oxide and at the Gate Oxide/Si Interface in Linear and Two-Dimensional Quantum Dot Arrays in Silicon

    by Saurabh Karwal, David J Michalak, Sergey V Amitonov, Larysa Tryputen, Amir Sammak, Marcel Meyer, Florian K Unseld, Corentin C Déprez, Ilja Meijer, Timo R. van Abswoude, et al.

    Some performance indicators of quantum computers can be traced back to the chip design and quality of materials comprising the quantum devices. Quantum states are fragile and may lose their state due to decoherence caused by a noisy environment [1,2,3]. Therefore, in addition to the growth of low-defect and low-disorder materials, reliable device fabrication with controlled densities of charge centers within the gate oxide and at the gate oxide/Si interface are also required. In this work, we report on state-of-the-art fabrication methods of linear and two-dimensional quantum dot array devices that are defined in isotopically purified in-house grown 28Si/SiGe heterostructures. Specifically, the two-dimensional quantum dot array devices presents a promising way forward for scaling up spin qubits, as such a device architecture allows for tunnel coupling between two adjacent quantum dots in two-dimensions [4]. However, scalable quantum processor might require the use of shared plunger and barrier gates, as demonstrated in the Ge/SiGe material platform [5], which entails a very high level of device uniformity in terms of potential landscape and associated control voltages required per qubit. Here, we report on electrical tuning of plunger gates performed in linear quantum dot array devices in order to achieve higher degree of electrical uniformity, thereby significantly reducing variations in the turn-on voltages [6]. Furthermore, following a similar electrical tuning procedure for plunger gates in a 2×2 two-dimensional quantum dot array devices enabled the realization of (1,1,1,1) charge state when all the plunger gates are set to 1 V, which may relax the requirements on control electronics and operations for spin qubit devices, as previously mentioned [7]. In parallel to electrical tuning of the quantum dots, the electrical quality and defect densities of the gate dielectric and its interface with the semiconductor heterostructure are being studied for correlation with electrical tuning ability as well as device drift, jumps, and charge noise [8,9]. Specifically, we measure capacitance-voltage (CV), conductance-voltage (GV), and capacitance-time (C-t) data at room temperature on test structure devices in order to distinguish between mobile charge defects (Qm ), interface trap defects (Dit ), oxide fixed charge (Qf ) and dielectric non-linearities. As the next step, we are working to characterize the activities of these defects down to cryogenic temperatures and ultimately control their densities for optimal device performance. [1] Zwanenburg et al., Rev. Mod. Phys. 85, 961 (2013). [2] Nicollian and Brews, MOS (Metal Oxide Semiconductor) Physics and Technology, (John Wiley & Sons, New York, 1982). [3] Wuetz et al., arXiv: arXiv:2209.07242. [4] Vandersypen et al., npj Quantum Inf 3, 34 (2017). [5] Borsoi et al., Nature Nanotech 19, 21 (2024). [6] Meyer et al., Nano Letters 23, 2522 (2023). [7] Meyer et al., Nano Letters 23, 11593 (2024). [8] Wuetz et al., Nat Comms 14, 1385 (2023). [9] Esposti et al., npj Quantum Info 10, 32 (2024).

  • Open Access

    Low-Temperature Plasma-Assisted Atomic-Layer-Deposited SnO2 as an Electron Transport Layer in Planar Perovskite Solar Cells

    by Yinghuan Kuang, Valerio Zardetto, Roderick van Gils, Saurabh Karwal, Dibyashree Koushik, Marcel A. Verheijen, Lachlan E. Black, Christ Weijtens, Sjoerd Veenstra, Ronn Andriessen, et al.

    In this work, we present an extensive characterization of plasma-assisted atomic-layer-deposited (ALD) SnO2 layers, with the aim of identifying key material properties of SnO2 to serve as an efficient electron transport layer (ETL) in perovskite solar cells (PSCs). Electrically resistive SnO2 films are fabricated at 50 °C, while a SnO2 film with a low electrical resistivity of 1.8 × 10-3 Ω cm, a carrier density of 9.6 × 1019 cm-3, and a high mobility of 36.0 cm2/Vs is deposited at 200 °C. Ultraviolet photoelectron spectroscopy indicates a conduction band offset of ~0.69 eV at the 50 °C SnO2/Cs0.05(MA0.17FA0.83)0.95Pb(I2.7Br0.3) interface. In contrast, a negligible conduction band offset is found between the 200 °C SnO2 and the perovskite. Surprisingly, comparable initial power conversion efficiencies (PCE) of 17.5% and 17.8% are demonstrated for the champion cells using 15 nm thick SnO2 deposited at 50 °C and 200 °C, respectively. The latter gains in fill factor but loses in open-circuit voltage. Markedly, PSCs using the 200 °C compact SnO2 retain their initial performance at the maximum power point over 16 hours under continuous one-sun illumination in inert atmosphere. Instead, the cell with the 50 °C SnO2 shows a decrease in PCE of approximately 50%.


  • Low-temperature plasma-enhanced atomic layer deposition of 2-D MoS 2 : large area, thickness control and tuneable morphology

    by Akhil Sharma, Marcel A. Verheijen, Longfei Wu, Saurabh Karwal, Vincent Vandalon, Harm C. M. Knoops, Ravi S. Sundaram, Jan P. Hofmann, W. M. M. (Erwin) Kessels, Ageeth A. Bol

    A low-temperature plasma enhanced atomic layer deposition process is demonstrated to synthesize high quality 2-D MoS 2 films with tuneable morphology.


  • Open Access

    Tuning Material Properties of Oxides and Nitrides by Substrate Biasing during Plasma-Enhanced Atomic Layer Deposition on Planar and 3D Substrate Topographies

    by Tahsin Faraz, Harm C. M. Knoops, Marcel A. Verheijen, Cristian A. A. van Helvoirt, Saurabh Karwal, Akhil Sharma, Vivek Beladiya, Adriana Szeghalmi, Dennis M. Hausmann, Jon Henri, et al.

    Oxide and nitride thin-films of Ti, Hf and Si serve numerous applications owing to the diverse range of their material properties. It is therefore imperative to have proper control over these properties during materials processing. Ion-surface interactions during plasma processing techniques can influence the properties of a growing film. In this work, we investigated the effects of controlling ion characteristics (energy, dose) on the properties of the aforementioned materials during plasma-enhanced atomic layer deposition (PEALD) on planar and 3D substrate topographies. We used a 200 mm remote PEALD system equipped with substrate biasing to control the energy and dose of ions by varying the magnitude and duration of the applied bias, respectively, during plasma exposure. Implementing substrate biasing in these forms enhanced PEALD process capability by providing two additional parameters for tuning a wide range of material properties. Below the regimes of ion-induced degradation, enhancing ion energies with substrate biasing during PEALD increased the refractive index and mass density of TiOx and HfOx and enabled control over their crystalline properties. PEALD of these oxides with substrate biasing at 150 °C led to the formation of crystalline material at the low temperature, which would otherwise yield amorphous films for deposition without biasing. Enhanced ion energies drastically reduced the resistivity of conductive TiNx and HfNx films. Furthermore, biasing during PEALD enabled the residual stress of these materials to be altered from tensile to compressive. The properties of SiOx were slightly improved whereas those of SiNx were degraded as a function of substrate biasing. PEALD on 3D trench nanostructures with biasing induced differing film properties at different regions of the 3D substrate. Based on the results presented herein, prospects afforded by the implementation of this technique during PEALD, such as enabling new routes for topographically selective deposition on 3D substrates, are discussed.


  • Low resistivity HfN x grown by plasma-assisted ALD with external rf substrate biasing

    by S. Karwal, M. A. Verheijen, B. L. Williams, T. Faraz, W. M. M. Kessels, M. Creatore

    Application of an external rf substrate bias during the H 2 plasma half cycle leads to a significant decrease in film resistivity resulting from a major reduction of O content and an increase in the Hf 3+ oxidation state fraction in HfN x thin films