Jeann Carlos da Silva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jeann Carlos da Silva has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Ana Flavia Nogueira
Institute of Chemistry
3 shared publications - Rodrigo Szostak
Brazilian Synchrotron Light Laboratory (LNLS), Brazilian Center for Research in Energy and Materials (CNPEM), Rua Giuseppe Máximo Solfaro, Campinas, Brazil
3 shared publications - Helio Cesar Nogueira Tolentino
Brazilian Synchrotron Light Laboratory (LNLS), Brazilian Center for Research in Energy and Materials (CNPEM), Rua Giuseppe Máximo Solfaro, Campinas, Brazil
2 shared publications - Marcio Medeiros Soares
Department of Physics, Universidade Federal da Paraíba, João Pessoa 58051-900, Brazil
2 shared publications - Paulo Ernesto Marchezi
Institute of Chemistry
2 shared publications Adriano dos Santos Marques
University of Campinas (UNICAMP), Laboratório de Nanotecnologia e Energia Solar, Chemistry Institute, Campinas, Brazil
1 shared publication
Latest Publications
- 22 June 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 8 (28) , 9697-9706
Effect of the incorporation of poly(ethylene oxide) copolymer on the stability of perovskite solar cells
Addition of poly(ethylene oxide- co -epichlorohydrin) to MAPbI 3 perovskite film enhanced cell stability under aggressive moisture exposure and prevented degradation from light.
- 22 June 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 8 (28) , 9697-9706
Effect of the incorporation of poly(ethylene oxide) copolymer on the stability of perovskite solar cells
Addition of poly(ethylene oxide- co -epichlorohydrin) to MAPbI 3 perovskite film enhanced cell stability under aggressive moisture exposure and prevented degradation from light.
- Open Access
- 11 October 2019
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 5 (10) , eaaw6619
Nanoscale mapping of chemical composition in organic-inorganic hybrid perovskite films
Lead-based organic-inorganic hybrid perovskite (OIHP) solar cells can attain efficiencies over 20%. However, the impact of ion mobility and/or organic depletion, structural changes, and segregation under operating conditions urge for decisive and more accurate investigations. Hence, the development of analytical tools for accessing the grain-to-grain OIHP chemistry is of great relevance. Here, we used synchrotron infrared nanospectroscopy (nano-FTIR) to map individual nanograins in OIHP films. Our results reveal a spatial heterogeneity of the vibrational activity associated to the nanoscale chemical diversity of isolated grains. It was possible to map the chemistry of individual grains in CsFAMA [Cs0.05FA0.79MA0.16Pb(I0.83Br0.17)3] and FAMA [FA0.83MA0.17Pb(I0.83Br0.17)3] films, with information on their local composition. Nanograins with stronger nano-FTIR activity in CsFAMA and FAMA films can be assigned to PbI2 and hexagonal polytype phases, respectively. The analysis herein can be extended to any OIHP films where organic cation depletion/accumulation can be used as a chemical label to study composition.
- 11 October 2019
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 5 (10) , eaaw6619
Open AccessNanoscale mapping of chemical composition in organic-inorganic hybrid perovskite films
Lead-based organic-inorganic hybrid perovskite (OIHP) solar cells can attain efficiencies over 20%. However, the impact of ion mobility and/or organic depletion, structural changes, and segregation under operating conditions urge for decisive and more accurate investigations. Hence, the development of analytical tools for accessing the grain-to-grain OIHP chemistry is of great relevance. Here, we used synchrotron infrared nanospectroscopy (nano-FTIR) to map individual nanograins in OIHP films. Our results reveal a spatial heterogeneity of the vibrational activity associated to the nanoscale chemical diversity of isolated grains. It was possible to map the chemistry of individual grains in CsFAMA [Cs0.05FA0.79MA0.16Pb(I0.83Br0.17)3] and FAMA [FA0.83MA0.17Pb(I0.83Br0.17)3] films, with information on their local composition. Nanograins with stronger nano-FTIR activity in CsFAMA and FAMA films can be assigned to PbI2 and hexagonal polytype phases, respectively. The analysis herein can be extended to any OIHP films where organic cation depletion/accumulation can be used as a chemical label to study composition.
- 21 June 2019
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 3 (9) , 2287-2297
Exploring the formation of formamidinium-based hybrid perovskites by antisolvent methods: in situ GIWAXS measurements during spin coating
Antisolvent methods – solvent engineering and a Lewis base adduct approach – are the most used methods to prepare highly efficient perovskite solar cells (PSCs). These two methods differ only by the ratio between the perovskite (PVSK) and dimethyl sulfoxide (DMSO). In this study, the difference between these two methods and the effect of relative humidity (rH) on the crystallization process were evaluated by in situ Grazing-Incidence Wide Angle X-ray Scattering (in situ GIWAXS) using synchrotron radiation. The technique was applied to the first stages of formation of formamidinium-based perovskite films, under real preparation conditions of spin coating, and at different humidity conditions and time windows to inject the antisolvent. The higher amount of DMSO in the solvent engineering method prolongs the duration of the colloidal gel, which extends the time window for antisolvent injection and, as a consequence, facilitates obtaining films with a homogeneous morphology. Our results confirm that the formation of a cesium/formamidinium-based perovskite takes place through the conversion of 2H–4H hexagonal polytypes directly to a black perovskite without thermal annealing, independent of the rH or method employed. In contrast, a cesium-free, methylammonium/formamidinium-based perovskite follows the 2H–4H–6H polytype sequence. Interestingly, at higher amounts of DMSO and rH (40%), a pure iodide intermediate (MA2Pb3I8·2DMSO) is formed in the cesium-free perovskite, which is undesirable in mixed halide perovskites. Our findings shed new light on the complexity of PVSK film formation, by identifying all crystalline phases in the process, and give clues to manage the composition and environment during film processing, and thus have an impact on efficiency optimization and solar cell manufacturing.
- 21 June 2019
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 3 (9) , 2287-2297
Exploring the formation of formamidinium-based hybrid perovskites by antisolvent methods: in situ GIWAXS measurements during spin coating
Antisolvent methods – solvent engineering and a Lewis base adduct approach – are the most used methods to prepare highly efficient perovskite solar cells (PSCs). These two methods differ only by the ratio between the perovskite (PVSK) and dimethyl sulfoxide (DMSO). In this study, the difference between these two methods and the effect of relative humidity (rH) on the crystallization process were evaluated by in situ Grazing-Incidence Wide Angle X-ray Scattering (in situ GIWAXS) using synchrotron radiation. The technique was applied to the first stages of formation of formamidinium-based perovskite films, under real preparation conditions of spin coating, and at different humidity conditions and time windows to inject the antisolvent. The higher amount of DMSO in the solvent engineering method prolongs the duration of the colloidal gel, which extends the time window for antisolvent injection and, as a consequence, facilitates obtaining films with a homogeneous morphology. Our results confirm that the formation of a cesium/formamidinium-based perovskite takes place through the conversion of 2H–4H hexagonal polytypes directly to a black perovskite without thermal annealing, independent of the rH or method employed. In contrast, a cesium-free, methylammonium/formamidinium-based perovskite follows the 2H–4H–6H polytype sequence. Interestingly, at higher amounts of DMSO and rH (40%), a pure iodide intermediate (MA2Pb3I8·2DMSO) is formed in the cesium-free perovskite, which is undesirable in mixed halide perovskites. Our findings shed new light on the complexity of PVSK film formation, by identifying all crystalline phases in the process, and give clues to manage the composition and environment during film processing, and thus have an impact on efficiency optimization and solar cell manufacturing.