Khaled Lahlou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Khaled Lahlou has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Chaimaa Diouri Ayad
The Civil, Climate, Water, Environment and Transport Engineering Laboratory (LaGCET), Ecole Hassania Des Travaux Publics (EHTP), Oasis, Morocco
2 shared publications - Abdelaziz Salmi
Structural and Material Mechanics team, National High School of Electricity and Mechanics, Hassan II University of Casablanca, Casablanca, Morocco
1 shared publication - Alexandros Margaritis
Belgian Road Research Centre
1 shared publication - Amina Alaoui
Ecole centrale des ponts et chaussées, Paris, France
1 shared publication - Amina Alaoui
Paris, France
1 shared publication - Cedric Vuye
University of Antwerp
1 shared publication
Latest Publications
- 19 April 2025
- Published by Springer Nature in Chemistry Africa
- Vol. 8 (5) , 1995-2018
Environmental Assessment of Phosphogypsum as Alternative Pavement Material
- 19 April 2025
- Published by Springer Nature in Chemistry Africa
- Vol. 8 (5) , 1995-2018
Environmental Assessment of Phosphogypsum as Alternative Pavement Material
- Open Access
- 2 April 2025
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Ecological Engineering & Environmental Technology
- Vol. 26 (4) , 374-388
Using phosphogypsum in road engineering: optimizing materials and structure
The yearly phosphogypsum (PG) production is significant, posing technical and environmental challenges for its permanent stacking. However, within the context of the circular economy, the value-adding of this coproduct in civil engineering, particularly in the construction of roads, is a viable...
- 2 April 2025
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Ecological Engineering & Environmental Technology
- Vol. 26 (4) , 374-388
Open AccessUsing phosphogypsum in road engineering: optimizing materials and structure
The yearly phosphogypsum (PG) production is significant, posing technical and environmental challenges for its permanent stacking. However, within the context of the circular economy, the value-adding of this coproduct in civil engineering, particularly in the construction of roads, is a viable...
- Open Access
- 1 July 2020
- Published by International Digital Organization for Scientific Information (IDOSI) in International Journal of Engineering
- Vol. 33 (7) , 1321-1330
A New Model of Equivalent Modulus Derived from Repeated Load CBR Test
This paper presents a new model of equivalent modulus derived from the Repeated Load CBR (RL-CBR) test without strain gauge. This model is an updated version of Araya et al. model (2011), the update consists of using the vertical strain as weighting factor instead of vertical displacement in the mean vertical and horizontal stresses calculation. The accuracy of equivalent modulus was improved by decreasing the relative error from 25% to 3%. The extra-large mold adopted by Araya et al. is used with a thickness of 8 mm instead of 14.5 mm. In experimental investigations, equivalent modulus may be calculated from experimental data and model parameters estimated by finite element (EF) simulation. There are five model parameters when the RL-CBR test is used, and three parameters when the strain gauge is not used. Model parameters are determined in two steps. First, the FE simulation of the RL-CBR test is conducted using various loading conditions (i.e., plunger penetration) and various quality ranges of unbound granular materials (UGM). In the second step, the non-linear multidimensional regression is accomplished to fit the equivalent modulus to Young’s modulus. The influence of FE analysis inputs is investigated to find the optimal inputs set that make the best compromise between the model accuracy and the calculation time consumption. The calculation of model parameters is carried out based on the optimal set data. Results from the new model and those from Araya et al. model are compared and have shown the improved accuracy of the developed model.
- 1 July 2020
- Published by International Digital Organization for Scientific Information (IDOSI) in International Journal of Engineering
- Vol. 33 (7) , 1321-1330
Open AccessA New Model of Equivalent Modulus Derived from Repeated Load CBR Test
This paper presents a new model of equivalent modulus derived from the Repeated Load CBR (RL-CBR) test without strain gauge. This model is an updated version of Araya et al. model (2011), the update consists of using the vertical strain as weighting factor instead of vertical displacement in the mean vertical and horizontal stresses calculation. The accuracy of equivalent modulus was improved by decreasing the relative error from 25% to 3%. The extra-large mold adopted by Araya et al. is used with a thickness of 8 mm instead of 14.5 mm. In experimental investigations, equivalent modulus may be calculated from experimental data and model parameters estimated by finite element (EF) simulation. There are five model parameters when the RL-CBR test is used, and three parameters when the strain gauge is not used. Model parameters are determined in two steps. First, the FE simulation of the RL-CBR test is conducted using various loading conditions (i.e., plunger penetration) and various quality ranges of unbound granular materials (UGM). In the second step, the non-linear multidimensional regression is accomplished to fit the equivalent modulus to Young’s modulus. The influence of FE analysis inputs is investigated to find the optimal inputs set that make the best compromise between the model accuracy and the calculation time consumption. The calculation of model parameters is carried out based on the optimal set data. Results from the new model and those from Araya et al. model are compared and have shown the improved accuracy of the developed model.
- Open Access
Lime Treatment of Coal Bottom Ash for Use in Road Pavements: Application to El Jadida Zone in Morocco
Industrial waste causes environmental, economic, and social problems. In Morocco, the Jorf Lasfar Thermal Power Station produces two types of coal ash with enormous quantities: fly ash (FA) and Bottom ash (BA). FA is recovered in cement while BA is stored in landfills. To reduce the effects of BA disposal in landfills, several experimental studies have tested the possibility of their recovery in the road construction, especially as a subbase. In the first phase of this study, the BA underwent a physicochemical and geotechnical characterization. The results obtained show that the BA should be treated to improve its mechanical properties. The most commonly used materials are lime and cement. In the selected low-cost treatment, which is the subject of the second phase of the study, lime is used to improve the low pozzolanicity of BA while calcarenite sand is used to increase the compactness. Several mixtures containing BA, lime, and calcarenite sand were prepared. Each of these mixtures was compacted in modified Proctor molds and then subjected to a series of tests to study the following characteristics: compressive strength, dry and wet California Bearing Ratio (CBR), dry density and swelling. The composition of each mixture was based on an experimental design approach. The results show that the values of the compressive strength, the dry density, and the CBR index have increased after treatment, potentially leading to a valorization of the treated BA for use in a subbase.
Open AccessLime Treatment of Coal Bottom Ash for Use in Road Pavements: Application to El Jadida Zone in Morocco
Industrial waste causes environmental, economic, and social problems. In Morocco, the Jorf Lasfar Thermal Power Station produces two types of coal ash with enormous quantities: fly ash (FA) and Bottom ash (BA). FA is recovered in cement while BA is stored in landfills. To reduce the effects of BA disposal in landfills, several experimental studies have tested the possibility of their recovery in the road construction, especially as a subbase. In the first phase of this study, the BA underwent a physicochemical and geotechnical characterization. The results obtained show that the BA should be treated to improve its mechanical properties. The most commonly used materials are lime and cement. In the selected low-cost treatment, which is the subject of the second phase of the study, lime is used to improve the low pozzolanicity of BA while calcarenite sand is used to increase the compactness. Several mixtures containing BA, lime, and calcarenite sand were prepared. Each of these mixtures was compacted in modified Proctor molds and then subjected to a series of tests to study the following characteristics: compressive strength, dry and wet California Bearing Ratio (CBR), dry density and swelling. The composition of each mixture was based on an experimental design approach. The results show that the values of the compressive strength, the dry density, and the CBR index have increased after treatment, potentially leading to a valorization of the treated BA for use in a subbase.