Kristian Krabbenhoft
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kristian Krabbenhoft has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
J. Krabbenhøft
Optum Computational Engineering, Copenhagen, Denmark
1 shared publicationJ. Wang
Offshore Wind Consultants Ltd., London, UK
1 shared publicationJørgen Krabbenhøft
Optum Computational Engineering Copenhagen Denmark
1 shared publication- Mohammed Hjiaj
Université Européenne de Bretagne
1 shared publication Noussaiba Graine
LGCGM/Structural Engineering Research Group INSA de Rennes Rennes Cedex 7 France
1 shared publication- Sergio Andres Galindo Torres
School of Engineering Westlake University Hangzhou China
1 shared publication
Latest Publications
- 1 April 2022
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 59 (4) , 614-619
Analytical stress–strain relation for soils
A new stress–strain relation capable of reproducing the entire stress–strain range of typical soil tests is presented. The new relation involves a total of five parameters, four of which can be inferred directly from typical test data. The fifth parameter is a fitting parameter with a relatively narrow range. The capabilities of the new relation are demonstrated by the application to various clay and sand datasets.
- 1 April 2022
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 59 (4) , 614-619
Analytical stress–strain relation for soils
A new stress–strain relation capable of reproducing the entire stress–strain range of typical soil tests is presented. The new relation involves a total of five parameters, four of which can be inferred directly from typical test data. The fifth parameter is a fitting parameter with a relatively narrow range. The capabilities of the new relation are demonstrated by the application to various clay and sand datasets.
- 1 October 2021
- Published by Elsevier in Computers and Geotechnics
- Vol. 138, 104146
Simplified kinematic hardening plasticity framework for constitutive modelling of soils
- 1 October 2021
- Published by Elsevier in Computers and Geotechnics
- Vol. 138, 104146
Simplified kinematic hardening plasticity framework for constitutive modelling of soils
- 5 December 2020
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 45 (2) , 265-290
3D failure envelope of a rigid pile embedded in a cohesive soil using finite element limit analysis
In this paper, numerical limit analysis is applied to evaluate the bearing capacity of a single rigid pile embedded in a ponderable homogeneous cohesive‐frictionless soil subjected to vertical, horizontal, and moment (VHM) loading combinations. All loads act in the same plane. Accurate lower and upper bounds are calculated using finite element limit analysis code . As the gap between the bounds hardly exceeds , the average limit load provides a good estimate of the exact ultimate load and can be used with confidence for design purposes. By adopting typical values for the dimensionless pile length‐to‐diameter ratio, most cases of practical interest are treated. The numerical results are compared against failure surfaces predicted by theories from the literature. Comparison shows that previously developed methods can be conservative or slightly overestimates the limit loads. New design charts are provided. The safe loads domain is constructed in the VHM space using the average limit load. Closed‐form expressions are proposed to describe the native and the normalized VMH failure envelope as a function of the pile length‐to‐diameter ratio. In the VH plane, the failure surface is described by an eccentric superellipse, whereas in the MH plane, the limit curve is an inclined ellipse.
- 5 December 2020
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 45 (2) , 265-290
3D failure envelope of a rigid pile embedded in a cohesive soil using finite element limit analysis
In this paper, numerical limit analysis is applied to evaluate the bearing capacity of a single rigid pile embedded in a ponderable homogeneous cohesive‐frictionless soil subjected to vertical, horizontal, and moment (VHM) loading combinations. All loads act in the same plane. Accurate lower and upper bounds are calculated using finite element limit analysis code . As the gap between the bounds hardly exceeds , the average limit load provides a good estimate of the exact ultimate load and can be used with confidence for design purposes. By adopting typical values for the dimensionless pile length‐to‐diameter ratio, most cases of practical interest are treated. The numerical results are compared against failure surfaces predicted by theories from the literature. Comparison shows that previously developed methods can be conservative or slightly overestimates the limit loads. New design charts are provided. The safe loads domain is constructed in the VHM space using the average limit load. Closed‐form expressions are proposed to describe the native and the normalized VMH failure envelope as a function of the pile length‐to‐diameter ratio. In the VH plane, the failure surface is described by an eccentric superellipse, whereas in the MH plane, the limit curve is an inclined ellipse.
- 22 August 2019
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 43 (17) , 2652-2666
AUS: Anisotropic undrained shear strength model for clays
Summary: A total stress model applicable to clays under undrained conditions is presented. The model involves three strength parameters: the undrained shear strengths in triaxial compression, triaxial extension, and simple shear. The amount of physical anisotropy implied by the model is a function of the relative magnitude of these three strengths assuming a Mises‐type plastic potential. Elastoplastic deformation characteristics below failure are accounted for by a hardening law requiring two additional parameters that can be related to the axial strains halfway to failure in triaxial compression and extension. Finally, elasticity is accounted for by Hooke law. The result is a relatively simple model whose parameters can all be inferred directly from a combination of in situ and standard undrained laboratory tests. The model is applied to a problem involving the horizontal loading of a monopile foundation for which full scale tests have been previously conducted. The model shows good agreement with the measured data.
- 22 August 2019
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 43 (17) , 2652-2666
AUS: Anisotropic undrained shear strength model for clays
Summary: A total stress model applicable to clays under undrained conditions is presented. The model involves three strength parameters: the undrained shear strengths in triaxial compression, triaxial extension, and simple shear. The amount of physical anisotropy implied by the model is a function of the relative magnitude of these three strengths assuming a Mises‐type plastic potential. Elastoplastic deformation characteristics below failure are accounted for by a hardening law requiring two additional parameters that can be related to the axial strains halfway to failure in triaxial compression and extension. Finally, elasticity is accounted for by Hooke law. The result is a relatively simple model whose parameters can all be inferred directly from a combination of in situ and standard undrained laboratory tests. The model is applied to a problem involving the horizontal loading of a monopile foundation for which full scale tests have been previously conducted. The model shows good agreement with the measured data.