Andreas Senz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andreas Senz has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Sebastian Strauß
Fraunhofer Institut für Gießerei, Composite und Verarbeitungstechnik IGCV
2 shared publications - Alptekin Celik
Institut für Kunststofftechnik, University of Stuttgart, 70569 Stuttgart, Germany
1 shared publication - Andrea Hohmann
Fraunhofer Institute for Casting, Composite and Processing Technology IGCV, Am Technologiezentrum 2, 86159 Augsburg, Germany
1 shared publication - Christian Bonten
Institut für Kunststofftechnik, University of Stuttgart, 70569 Stuttgart, Germany
1 shared publication - Frederik Wilhelm
Fraunhofer Institute for Casting, Composites and Processing, 86159 Augsburg, Germany
1 shared publication - Frederik Wilhelm
Fraunhofer Institute for Casting, Composite and Processing Technology IGCV, Am Technologiezentrum 2, 86159 Augsburg, Germany
1 shared publication
Latest Publications
- Open Access
Sustainable Pultruded Sandwich Profiles with Mycelium Core
This research focuses on exploring the potential of mycelium as a sustainable alternative to wood or solid foam in pultruded glass fiber-reinforced plastic (GFRP) sandwich profiles. The study evaluates the performance and the environmental sustainability potential of this composite by mechanical tests and life cycle assessment (LCA). Analysis and comparison of pultruded sandwich profiles with mycelium, polyurethane (PUR) foam and chipboard demonstrate that mycelium is competitive in terms of its performance and environmental impact. The LCA indicates that 88% of greenhouse gas emissions are attributed to mycelium production, with the heat pressing (laboratory scale) being the main culprit. When pultruded profiles with mycelium cores of densities 350 and 550 kg/m³ are produced using an oil-heated lab press, a global warming potential (GWP) of 5.74 and 9.10 kg CO2-eq. per functional unit was calculated, respectively. When using an electrically heated press, the GWP decreases to 1.50 and 1.78 kg CO2-eq. Compared to PUR foam, a reduction of 23% in GWP is possible. In order to leverage this potential, the material performance and the reproducibility of the properties must be further increased. Additionally, an adjustment of the manufacturing process with in situ mycelium deactivation during pultrusion could further reduce the energy consumption.
Open AccessSustainable Pultruded Sandwich Profiles with Mycelium Core
This research focuses on exploring the potential of mycelium as a sustainable alternative to wood or solid foam in pultruded glass fiber-reinforced plastic (GFRP) sandwich profiles. The study evaluates the performance and the environmental sustainability potential of this composite by mechanical tests and life cycle assessment (LCA). Analysis and comparison of pultruded sandwich profiles with mycelium, polyurethane (PUR) foam and chipboard demonstrate that mycelium is competitive in terms of its performance and environmental impact. The LCA indicates that 88% of greenhouse gas emissions are attributed to mycelium production, with the heat pressing (laboratory scale) being the main culprit. When pultruded profiles with mycelium cores of densities 350 and 550 kg/m³ are produced using an oil-heated lab press, a global warming potential (GWP) of 5.74 and 9.10 kg CO2-eq. per functional unit was calculated, respectively. When using an electrically heated press, the GWP decreases to 1.50 and 1.78 kg CO2-eq. Compared to PUR foam, a reduction of 23% in GWP is possible. In order to leverage this potential, the material performance and the reproducibility of the properties must be further increased. Additionally, an adjustment of the manufacturing process with in situ mycelium deactivation during pultrusion could further reduce the energy consumption.
- Open Access
Experimental and Simulative Analysis of the Pressure Development in a Closed Injection Pultrusion Process with Multiple Chamber Geometries
The use of innovative higher-performance highly reactive resin systems requires an enhancement of the established method of fiber impregnation (open bath) towards closed resin-injection pultrusion (CIP), due to the short pot life of the resin systems. The result is that the open bath is developed into a closed injection and impregnation chamber (“ii-chamber”). In this study, three parameters—resin viscosity, opening angle and opening factor at the injection point on the ii-chamber—are varied, each in three stages. For each set of parameters, a pultrusion trial is conducted and the process pressures in the ii-chamber and pultrusion die measured. This enables direct feedback via the process conditions of the as yet uncured composite. The data obtained are used to validate a newly developed simulation model. The model is based on Darcy’s law, which has been extended to take fiber movement into account and thus represent the resulting pressure increase in the die. The flexible ii-chamber and die concept enhance our understanding of the processes taking place in the die system. The sensitivity of the process pressures can be shown for the three influencing variables. The experiment shows that of the three influencing variables investigated, viscosity has the greatest sensitivity to pressure development. In general, it can be said that over the length of the pultrusion die system, the pressure level increases across the three measuring points.
Open AccessExperimental and Simulative Analysis of the Pressure Development in a Closed Injection Pultrusion Process with Multiple Chamber Geometries
The use of innovative higher-performance highly reactive resin systems requires an enhancement of the established method of fiber impregnation (open bath) towards closed resin-injection pultrusion (CIP), due to the short pot life of the resin systems. The result is that the open bath is developed into a closed injection and impregnation chamber (“ii-chamber”). In this study, three parameters—resin viscosity, opening angle and opening factor at the injection point on the ii-chamber—are varied, each in three stages. For each set of parameters, a pultrusion trial is conducted and the process pressures in the ii-chamber and pultrusion die measured. This enables direct feedback via the process conditions of the as yet uncured composite. The data obtained are used to validate a newly developed simulation model. The model is based on Darcy’s law, which has been extended to take fiber movement into account and thus represent the resulting pressure increase in the die. The flexible ii-chamber and die concept enhance our understanding of the processes taking place in the die system. The sensitivity of the process pressures can be shown for the three influencing variables. The experiment shows that of the three influencing variables investigated, viscosity has the greatest sensitivity to pressure development. In general, it can be said that over the length of the pultrusion die system, the pressure level increases across the three measuring points.
- Open Access
- 23 August 2019
- Published by MDPI AG in Journal of Composites Science
- Vol. 3 (3) , 87
Comparison of the Processing of Epoxy Resins in Pultrusion with Open Bath Impregnation and Closed-Injection Pultrusion
In this study, the influence of the open bath and closed-injection pultrusion (CIP) processing methods of epoxy resins on the quality of glass fiber composites was investigated. In addition to the state-of-the-art epoxy resin system with long pot life, new resin systems with short pot life have recently been developed. These systems require processing by closed-injection pultrusion. The epoxies with long pot life allow both processing variants. The experimental work was carried out with two types of injection and impregnation chambers (ii_chamber), namely with a conical and a teardrop design. Fully impregnated composites, which were used for further analyses, could be produced by using the conical ii_chamber. The composite properties of the open bath and the conical ii_chamber impregnation methods were compared. No significant influence on the bending stress could be determined; the interlaminar shear strength was up to 10% better with open bath impregnation than with ii_chamber. For the composites investigated, it was shown that the open bath and ii_chamber impregnation methods can be used to produce parts with partially comparable properties, as demonstrated for the epoxy formulation with long pot life. These results indicate that processing of epoxy systems with a short pot life is also possible by closed-injection pultrusion. Furthermore, the influence on the composite properties of the time interval between the mixing of an epoxy resin and processing in an open bath was investigated. No significant effect on the bending stress and interlaminar shear strength could be determined.
- 23 August 2019
- Published by MDPI AG in Journal of Composites Science
- Vol. 3 (3) , 87
Open AccessComparison of the Processing of Epoxy Resins in Pultrusion with Open Bath Impregnation and Closed-Injection Pultrusion
In this study, the influence of the open bath and closed-injection pultrusion (CIP) processing methods of epoxy resins on the quality of glass fiber composites was investigated. In addition to the state-of-the-art epoxy resin system with long pot life, new resin systems with short pot life have recently been developed. These systems require processing by closed-injection pultrusion. The epoxies with long pot life allow both processing variants. The experimental work was carried out with two types of injection and impregnation chambers (ii_chamber), namely with a conical and a teardrop design. Fully impregnated composites, which were used for further analyses, could be produced by using the conical ii_chamber. The composite properties of the open bath and the conical ii_chamber impregnation methods were compared. No significant influence on the bending stress could be determined; the interlaminar shear strength was up to 10% better with open bath impregnation than with ii_chamber. For the composites investigated, it was shown that the open bath and ii_chamber impregnation methods can be used to produce parts with partially comparable properties, as demonstrated for the epoxy formulation with long pot life. These results indicate that processing of epoxy systems with a short pot life is also possible by closed-injection pultrusion. Furthermore, the influence on the composite properties of the time interval between the mixing of an epoxy resin and processing in an open bath was investigated. No significant effect on the bending stress and interlaminar shear strength could be determined.