Wenyi Xie
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wenyi Xie has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Gregory N. Parsons
Department of Chemical and Biomolecular Engineering, North Carolina State University, Raleigh, NC 27695, USA
5 shared publications - Saad A. Khan
Chemical and Biomolecular Engineering North Carolina State University 911 Partners Way Raleigh NC 27695 USA
3 shared publications - Orlando J. Rojas
The University of British Columbia
2 shared publications E.E. Anderson
1 shared publicationHolger Saare
Department of Physics, North Carolina State University 1 , Raleigh, North Carolina 27695
1 shared publicationJulie A. Willoughby
Department of Textile Engineering, Chemistry and Science, North Carolina State University, 2401 Research Drive, Raleigh, North Carolina 27695, United States
1 shared publication
Latest Publications
- Open Access
- 20 June 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (4)
Comparison of BCl3, TiCl4, and SOCl2 chlorinating agents for atomic layer etching of TiO2 and ZrO2 using tungsten hexafluoride
Recent advances in the semiconductor industry have created an exigency for processes that allow to deposit and etch material in conformal matter in three-dimensional devices. While conformal deposition is achieved using atomic layer deposition (ALD), conformal etching can be accomplished by thermal atomic layer etching (ALE) which, like ALD, proceeds via a binary sequence of self-limiting reactions. This study explores ALE of TiO2 and ZrO2 using WF6 as a fluorinating agent, and BCl3, TiCl4, or SOCl2 as a co-reactant. The effect of co-reactant chemistry was studied using atomic force microscopy, in situ ellipsometry, and in vacuo Auger electron spectroscopy measurements along with thermodynamic modeling. All three co-reactants exhibited saturation and etch rates increasing with temperature. At 170 °C, TiO2 can be etched using WF6 with BCl3, TiCl4, or SOCl2, and the etching proceeds at 0.24, 0.18, and 0.20 nm/cycle, respectively. At 325 °C, ZrO2 ALE can occur using these same reactants, proceeding at 0.96, 0.74, and 0.13 nm/cycle, respectively. A higher temperature is needed for ZrO2 ALE versus TiO2 because the ZrCl4 product is less volatile than the corresponding TiCl4. During ZrO2 and TiO2 etching using BCl3 or TiCl4, boron oxide or titanium oxide intermediate layers, respectively, were formed on the surface, and they were subsequently removed by WF6. In contrast, for ALE of TiO2 using SOCl2, a similar intermediate layer is not observed. This study broadens the understanding of co-etchants role during thermal ALE and expands the range of reactants that can be used for vapor etching of metal oxides.
- 20 June 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (4)
Open AccessComparison of BCl3, TiCl4, and SOCl2 chlorinating agents for atomic layer etching of TiO2 and ZrO2 using tungsten hexafluoride
Recent advances in the semiconductor industry have created an exigency for processes that allow to deposit and etch material in conformal matter in three-dimensional devices. While conformal deposition is achieved using atomic layer deposition (ALD), conformal etching can be accomplished by thermal atomic layer etching (ALE) which, like ALD, proceeds via a binary sequence of self-limiting reactions. This study explores ALE of TiO2 and ZrO2 using WF6 as a fluorinating agent, and BCl3, TiCl4, or SOCl2 as a co-reactant. The effect of co-reactant chemistry was studied using atomic force microscopy, in situ ellipsometry, and in vacuo Auger electron spectroscopy measurements along with thermodynamic modeling. All three co-reactants exhibited saturation and etch rates increasing with temperature. At 170 °C, TiO2 can be etched using WF6 with BCl3, TiCl4, or SOCl2, and the etching proceeds at 0.24, 0.18, and 0.20 nm/cycle, respectively. At 325 °C, ZrO2 ALE can occur using these same reactants, proceeding at 0.96, 0.74, and 0.13 nm/cycle, respectively. A higher temperature is needed for ZrO2 ALE versus TiO2 because the ZrCl4 product is less volatile than the corresponding TiCl4. During ZrO2 and TiO2 etching using BCl3 or TiCl4, boron oxide or titanium oxide intermediate layers, respectively, were formed on the surface, and they were subsequently removed by WF6. In contrast, for ALE of TiO2 using SOCl2, a similar intermediate layer is not observed. This study broadens the understanding of co-etchants role during thermal ALE and expands the range of reactants that can be used for vapor etching of metal oxides.
- Open Access
- 1 December 2020
- Published by Elsevier in Materials Today Advances
- Vol. 8
Polymer of intrinsic microporosity (PIM) based fibrous mat: combining particle filtration and rapid catalytic hydrolysis of chemical warfare agent simulants into a highly sorptive, breathable, and mechanically robust fiber matrix
- 1 December 2020
- Published by Elsevier in Materials Today Advances
- Vol. 8
Open AccessPolymer of intrinsic microporosity (PIM) based fibrous mat: combining particle filtration and rapid catalytic hydrolysis of chemical warfare agent simulants into a highly sorptive, breathable, and mechanically robust fiber matrix
- 28 January 2020
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 38 (2) , 022605
Thermal atomic layer etching of metallic tungsten via oxidation and etch reaction mechanism using O2 or O3 for oxidation and WCl6 as the chlorinating etchant
Atomic layer etching (ALE), offering highly controlled removal of thin film materials, is considered as an enabling process technology for future development of transistor devices. The authors previously reported a thermal tungsten (W) ALE process using WF6 and O2 for temperatures ≥275 °C, and they recently discovered the opportunity for low-temperature W etching using WCl6 as the etchant instead of WF6. This article demonstrates a two-step, thermal W ALE process viable for temperatures ≥200 °C, consisting of an oxidation half-reaction with O2 or O3 and an etch half-reaction using WCl6 as the chlorinating etchant. In situ quartz crystal microbalance (QCM) analysis reveals that W ALE using O2 and WCl6 is self-limiting and proceeds at an etch rate of ∼7.3–8.2 Å/cycle for temperatures between 205 and 235 °C. QCM analysis further reveals a surface dependence in the etch rate of the O2/WCl6 process, where the etch rate is the largest during the first cycle and decreases to a smaller value in later cycles. In addition, the authors show that O3 is a more effective oxidant than O2 for W ALE at lower temperatures; saturation is achieved with a much shorter exposure. Etching of W films on silicon substrates was confirmed using ex situ techniques. Overall, this study increases the understanding of surface reactions in thermal ALE and expands the range of etchants and coreactants that are useful for thermal etching of metallic thin films.
- 28 January 2020
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 38 (2) , 022605
Thermal atomic layer etching of metallic tungsten via oxidation and etch reaction mechanism using O2 or O3 for oxidation and WCl6 as the chlorinating etchant
Atomic layer etching (ALE), offering highly controlled removal of thin film materials, is considered as an enabling process technology for future development of transistor devices. The authors previously reported a thermal tungsten (W) ALE process using WF6 and O2 for temperatures ≥275 °C, and they recently discovered the opportunity for low-temperature W etching using WCl6 as the etchant instead of WF6. This article demonstrates a two-step, thermal W ALE process viable for temperatures ≥200 °C, consisting of an oxidation half-reaction with O2 or O3 and an etch half-reaction using WCl6 as the chlorinating etchant. In situ quartz crystal microbalance (QCM) analysis reveals that W ALE using O2 and WCl6 is self-limiting and proceeds at an etch rate of ∼7.3–8.2 Å/cycle for temperatures between 205 and 235 °C. QCM analysis further reveals a surface dependence in the etch rate of the O2/WCl6 process, where the etch rate is the largest during the first cycle and decreases to a smaller value in later cycles. In addition, the authors show that O3 is a more effective oxidant than O2 for W ALE at lower temperatures; saturation is achieved with a much shorter exposure. Etching of W films on silicon substrates was confirmed using ex situ techniques. Overall, this study increases the understanding of surface reactions in thermal ALE and expands the range of etchants and coreactants that are useful for thermal etching of metallic thin films.
- 9 December 2019
- Published by Wiley in Advanced Functional Materials
- Vol. 30 (5)
Cellulose Silica Hybrid Nanofiber Aerogels: From Sol–Gel Electrospun Nanofibers to Multifunctional Aerogels
Aerogels are considered ideal candidates for various applications, because of their low bulk density, highly porous nature, and functional performance. However, the time intensive nature of the complex fabrication process limits their potential application in various fields. Recently, incorporation of a fibrous network has resulted in production of aerogels with improved properties and functionalities. A facile approach is presented to fabricate hybrid sol–gel electrospun silica‐cellulose diacetate (CDA)‐based nanofibers to generate thermally and mechanically stable nanofiber aerogels. Thermal treatment results in gluing the silica‐CDA network strongly together thereby enhancing aerogel mechanical stability and hydrophobicity without compromising their highly porous nature (>98%) and low bulk density (≈10 mg cm−3). X‐ray photoelectron spectroscopy and in situ Fourier‐transform infrared studies demonstrate the development of strong bonds between silica and the CDA network, which result in the fabrication of cross‐linked structure responsible for their mechanical and thermal robustness and enhanced affinity for oils. Superhydrophobic nature and high oleophilicity of the hybrid aerogels enable them to be ideal candidates for oil spill cleaning, while their flame retardancy and low thermal conductivity can be explored in various applications requiring stability at high temperatures.
- 9 December 2019
- Published by Wiley in Advanced Functional Materials
- Vol. 30 (5)
Cellulose Silica Hybrid Nanofiber Aerogels: From Sol–Gel Electrospun Nanofibers to Multifunctional Aerogels
Aerogels are considered ideal candidates for various applications, because of their low bulk density, highly porous nature, and functional performance. However, the time intensive nature of the complex fabrication process limits their potential application in various fields. Recently, incorporation of a fibrous network has resulted in production of aerogels with improved properties and functionalities. A facile approach is presented to fabricate hybrid sol–gel electrospun silica‐cellulose diacetate (CDA)‐based nanofibers to generate thermally and mechanically stable nanofiber aerogels. Thermal treatment results in gluing the silica‐CDA network strongly together thereby enhancing aerogel mechanical stability and hydrophobicity without compromising their highly porous nature (>98%) and low bulk density (≈10 mg cm−3). X‐ray photoelectron spectroscopy and in situ Fourier‐transform infrared studies demonstrate the development of strong bonds between silica and the CDA network, which result in the fabrication of cross‐linked structure responsible for their mechanical and thermal robustness and enhanced affinity for oils. Superhydrophobic nature and high oleophilicity of the hybrid aerogels enable them to be ideal candidates for oil spill cleaning, while their flame retardancy and low thermal conductivity can be explored in various applications requiring stability at high temperatures.
- 6 September 2018
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 6 (11) , 13844-13853
Control of Micro- and Mesopores in Carbon Nanofibers and Hollow Carbon Nanofibers Derived from Cellulose Diacetate via Vapor Phase Infiltration of Diethyl Zinc
- 6 September 2018
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 6 (11) , 13844-13853
Control of Micro- and Mesopores in Carbon Nanofibers and Hollow Carbon Nanofibers Derived from Cellulose Diacetate via Vapor Phase Infiltration of Diethyl Zinc
- 20 February 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (10) , 9147-9154
Thermally Driven Self-Limiting Atomic Layer Etching of Metallic Tungsten Using WF6 and O2
The semiconductor industry faces a tremendous challenge in the development of transistor device with sub-10nm complex features. Self-limiting atomic layer etching (ALE) is essential for enabling the manufacturing of complex transistor structures. In this study, we demonstrated a thermally driven ALE process for tungsten (W) using sequential exposures of O2 and WF6. Based on the insight gained from the previous study on TiO2 thermal ALE, we proposed that etching of W could proceed in two sequential reaction steps at 300 °C: 1) oxidation of metallic tungsten using O2 or O3 to form WO3(s), and 2) formation and removal of volatile WO2F2(g) during the reaction between WO3(s) and WF6(g). The O2/WF6 etch process was experimentally studied using quartz crystal microbalance (QCM). We find that that both the O2 and WF6 ALE half reactions are self-limiting, with an estimated steady-state etch rate of ~ 6.3 Å/cycle at 300 °C. We also find that etching of W proceeds readily at 300 °C, but not at temperatures lower than 275 °C. Thermodynamic modeling reveals that the observed temperature dependence is likely due to the limited volatility of WO2F2. Using WF6 with O3 in place of O2 also allows W etching, where the stronger oxidant leads to a larger mass removal rate per cycle. However, we find O2 to be more controllable for precise metal removal per cycle. In addition, etched W films were examined with ex-situ analytical tools. Using spectroscopic ellipsometry (SE) and scanning electron microscopy (SEM), we confirm etching of tungsten film on silicon substrates. Surface analysis by x-ray photoelectron spectroscopy (XPS) revealed a minimal fluorine content on the W film after partial etching, and on the silicon surface after full etching. This suggests that W ALE does not significantly alter the chemical composition of W films. This work serves to increase the understanding on ALE reactions and expand the base of available ALE processes for advanced material processing.
- 20 February 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (10) , 9147-9154
Thermally Driven Self-Limiting Atomic Layer Etching of Metallic Tungsten Using WF6 and O2
The semiconductor industry faces a tremendous challenge in the development of transistor device with sub-10nm complex features. Self-limiting atomic layer etching (ALE) is essential for enabling the manufacturing of complex transistor structures. In this study, we demonstrated a thermally driven ALE process for tungsten (W) using sequential exposures of O2 and WF6. Based on the insight gained from the previous study on TiO2 thermal ALE, we proposed that etching of W could proceed in two sequential reaction steps at 300 °C: 1) oxidation of metallic tungsten using O2 or O3 to form WO3(s), and 2) formation and removal of volatile WO2F2(g) during the reaction between WO3(s) and WF6(g). The O2/WF6 etch process was experimentally studied using quartz crystal microbalance (QCM). We find that that both the O2 and WF6 ALE half reactions are self-limiting, with an estimated steady-state etch rate of ~ 6.3 Å/cycle at 300 °C. We also find that etching of W proceeds readily at 300 °C, but not at temperatures lower than 275 °C. Thermodynamic modeling reveals that the observed temperature dependence is likely due to the limited volatility of WO2F2. Using WF6 with O3 in place of O2 also allows W etching, where the stronger oxidant leads to a larger mass removal rate per cycle. However, we find O2 to be more controllable for precise metal removal per cycle. In addition, etched W films were examined with ex-situ analytical tools. Using spectroscopic ellipsometry (SE) and scanning electron microscopy (SEM), we confirm etching of tungsten film on silicon substrates. Surface analysis by x-ray photoelectron spectroscopy (XPS) revealed a minimal fluorine content on the W film after partial etching, and on the silicon surface after full etching. This suggests that W ALE does not significantly alter the chemical composition of W films. This work serves to increase the understanding on ALE reactions and expand the base of available ALE processes for advanced material processing.
- 10 January 2018
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 6 (2) , 1988-1998
Thermally Stable and Tough Coatings and Films Using Vinyl Silylated Lignin
- 10 January 2018
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 6 (2) , 1988-1998
Thermally Stable and Tough Coatings and Films Using Vinyl Silylated Lignin